Wolf CW24 User manual

General Information 2

Controls & Operation 4

Component Access & Removal 8

Troubleshooting Guide 13

Technical Data 16

Wiring Diagrams 17

subzero.com 800.222.7820

CW24 Cup Warming Drawer

Service Manual

Page 2

Cup Warming Drawer (CW24)

General Information

1-2

#9001337 - Revision A - September, 2015

INTRODUCTION

This Technical Service Manual has been compiled to provide the most recent technical service information. This

information will enable the service technician to troubleshoot and diagnose malfunctions, perform necessary repairs

and return the appliance to proper operational condition.

The service technician should read the complete instructions contained in this service manual before initiating any

repairs on a Wolf Appliance.

For installation information see Cup Warming Drawers Installation Guide available at http://www.subzero-

wolf.com/trade-resources/product-specifications.

For Use and Care information see Cup Warming Drawers Use & Care Guide available at http://www.subzero-

wolf.com/trade-resources/product-specifications.

IMPORTANT SAFETY INFORMATION

Below are the Product Safety Labels used in this manu-

al. The "Signal Words" used are WARNING and

CAUTION.

Please note that these safety labels are placed in areas

where awareness of personal safety and product safety

should be taken and lists the precautions to be taken

when the signal word is observed.

This manual is designed to be used by Certified Service Personnel only. Wolf Appliance, Inc. assumes no

responsibility for any repairs made to Wolf appliances by anyone other than Certified Service Technicians.

INDICATES THAT HAZARDOUS OR UNSAFE

PRACTICES COULD RESULT IN SEVERE PERSON-

AL INJURY OR DEATH.

Indicates that hazardous or unsafe practices could

result in minor personal injury or product and/or

property damage

In addition, please pay attention to the signal word

“NOTE”, which highlights especially important informa-

tion within each section.

The information and images are the copyright property of Wolf Appliance, Inc., an affiliate of

Sub-Zero Group, Inc. Neither this manual nor any information or images contained herein may be copied or used in

whole or in part without the express written permission of Wolf Appliance, Inc., an affiliate of Sub-Zero Group, Inc. ©

TECHNICAL ASSISTANCE

If you should have any questions regarding the appli-

ance and/or this manual, please contact:

Wolf Appliance, Inc.

ATTN: Service Department

P.O. Box 44988

Madison, WI 53744 - 4988

Customer Care

Phone #: (800) 332 - 9513

Facsimile #: (608) 441 - 5887

Technical Assistance

(For Technicians in Customer’s Homes Only)

Phone #: (800) 919 - 8324

Warranty Claims

Phone #: (800) 404 - 7820

Facsimile #: (608) 441 - 5886

Service Department e-mail Address:

[email protected]

Main Office Hours:

8:00 AM to 5:00 PM Central Time

Monday through Friday

(24/7 Phone Coverage)

Page 3

General Information

Cup Warming Drawer (CW24)

1-3 #9001337 - Revision A - September, 2015

WARRANTY INFORMATION

This page contains a summary of the Warranty supplied with every Domestic Cup Warming Drawer (CW24).

2 & 5 Year Warranty Summary:

2 Year Total Product Warranty, Parts and Labor.•

3-5 Limited Parts Only Warranty.•

Details:

Warranty applies to products installed in United States or Canada, for residential use only.•

Warranty begins at time of unit’s initial installation.•

Warranty does not cover Wolf Appliances installed in a demonstration kitchen, test kitchen, culinary school•

kitchen, or similar installations. (See Special Warranty below)

Warranty and service information collected by Wolf Appliance, Inc. is arranged and stored under unit serial num-•

ber and/or customer’s name. Wolf Appliance, Inc requests that you have model and serial number available

whenever contacting factory or parts distributor.

3-5 Year Limited Parts Only Warranty applies to the heating element and the user interface.•

Special Warranty Summary

2 Year Total Product Warranty, Part and Labor.

Details:

This Warranty applies to products installed in United States or Canada, for use in a demonstration kitchen, test•

kitchen, culinary school kitchen, and similar installations that will help promote Wolf Appliance brand and its

products.

Warranty begins at time of unit’s initial installation.•

Warranty and Service information collected by Wolf Appliance, Inc. is arranged and stored under unit serial num-•

ber and/or customer’s name. Wolf Appliance, Inc. requests that you have model and serial number available

whenever contacting factory or parts distributor.

NOTE: “ICB” appliances carry no factory warranty. The product distributor or appliance dealer may offer their own

warranty.

Figure 1-2. The rating plate is located on the fan housing.

Figure 1-1. Typical Rating Label Layout

CW24/B

120V ~ 60Hz 420W

943028

G15D4Type.:

Madei

nPortu

gal

Fabriqué auPo

rtugal

Household Use Only

Seulement pour applications domestiques

Ser. Nº.:

137750779

Manufactured:October 2014

Rating Plate

Page 4

Cup Warming Drawer (CW24)

General Information

1-4

#9001337 - Revision A - September, 2015

Refer to this key for an example of the model numbers.

Model: ICBCW 24 / S

International Designation

Product Configuration

Size

Finish

Product Configuration

CW = Cup Warming Drawer

Size

24 = 24 - inch wide unit

Finish

SClassic Stainless Steel

BBlack Glass

• Two finishes

Classic Stainless Steel

Black Glass

• Hidden electronic touch controls

• 420 watt heating element with temperature control

range of 85° F to 175° F

• Automatic shut off

• Delayed Start

• Push - pull drawer opening

• Full extension, ball-bearing drawer glides

• Removable, non-slip drawer liner

• Sabbath mode

CUP WARMING DRAWER FEATURES

MODEL NUMBER KEY

Page 5

Cup Warming Drawer (CW24)

Electronics

2-2

#9001337 - Revision A - September, 2015

Cup Warming Drawer Electronics

This section describes the basic operation of the Cup Warming Drawer (CW24) electronics and how the user inter-

face responds to input commands. The user interface has three buttons that use a relay to open and close switches.

User Interface Buttons (See Figure 2-1)

ON/MENU Button

Turns unit on.•

Cycles user interface between menu options TEMP, TIMER, and DELAY START.•

Used with MORE button to enter Sabbath mode.•

Used with LESS/OFF button to exit Sabbath mode.•

LESS/OFF Button

Decreases TEMP, TIMER, and DELAY START settings.•

Depressed for three seconds turns the CW24 off.•

Used with ON/MENU button to exit Sabbath mode.•

MORE Button

Increases TEMP, TIMER, and DELAY START settings.•

Used with ON/MENU button to enter Sabbath mode.•

Figure 2-1. CW24 User Interface

Page 6

Electronics

Cup Warming Drawer (CW24)

2-3 #9001337 - Revision A - September, 2015

General Features of the User Interface

Temperature

Temperature Range is 85° F to 175° F, and increases and decrease by 10° intervals.•

Temperature display goes in a circle.•

If 175° F and MORE button is pressed, temperature goes to 85° F.•

If 85° F and LESS/OFF is pressed, temperature goes to 175° F.•

Timer

Timer is programmable from 1 minute to 4 hours.•

Timer increases and decreases by different increments.•

From 1 minute to 15 minutes changes by one minute intervals.•

From 15 minutes to 1 hour changes by five minute intervals.•

From 1 hour to 4 hours by ten minute intervals.•

Delay Start

Delay Start is programmable from 1 minute to 9 hours, 50 minutes.•

Delay Start increases and decreases by different increments.•

From 1 minute to 15 minutes and changes by one minute intervals.•

From 15 minutes to 1 hour and changes by five minute intervals.•

From 1 hour to 9 hours, 50 minutes and changes by ten minute intervals.•

Page 7

Cup Warming Drawer (CW24)

Electronics

2-4

#9001337 - Revision A - September, 2015

User Interface Operation

Program the unit without DELAY START

Press ON/MENU. TEMP and 85° F flashes on the1

display (See Figure 2-2).

Press the MORE button to increase the tempera-2

ture.

NOTE: The display flashes three times then shuts off if

no other button is pressed.

Press ON/MENU when desired temperature is set.3

TIMER and 0h00 flashes on the display (See Figure4

2-3).

Press LESS/OFF or MORE button to set the amount5

of time the unit is to run between one minute and

four hours.

Press ON/MENU when desired time is set.6

DELAY START and 0h00 flashes on the display.7

Press ON/MENU, the temperature flashes for three8

seconds, then the fan comes on.

The display alternates between the setpoint temper-9

ature and the remaining time on the timer.

Program the unit with DELAY START

Press ON/MENU. TEMP and 85° F flashes on the1

display (See Figure 2-2).

Press the MORE button to increase the tempera-2

ture.

NOTE: The display flashes three times, then shut off if

no other button is pressed.

Press ON/MENU when desired temperature is set.3

TIMER and 0h00 flashes on the display (See Figure4

2-3).

Press LESS/OFF or MORE button to set the amount5

of time the unit is to run between one minute and

four hours.

Press ON/MENU when desired time is set.6

DELAY START and 0h00 flashes on the display.7

Press LESS/OFF or MORE button to set the amount8

of time before the unit starts, between one minute

and nine hours, 50 minutes (See Figure 2-4).

Press ON/MENU when the desired time is set.9

Temperature flashes for three seconds, then the dis-10

play shows the time remaining until the unit starts.

When the DELAY START time expires, the unit11

starts and the display alternates between the set-

point temperature and the remaining time on the

timer.

Figure 2-2. Setting Temperature

Figure 2-3. Setting Timer

Figure 2-4. Delay Start Display

Page 8

Electronics

Cup Warming Drawer (CW24)

2-5 #9001337 - Revision A - September, 2015

Turn the Unit Off

The Cup Warming Drawer can be shut off at any time or

during any mode, except Sabbath mode.

Press and hold the LESS/OFF button for three sec-1

onds.

Display shuts off.2

Fan runs for 60 seconds then shut off.3

Entering Sabbath Mode

Press and hold the ON/MENU button and the1

MORE button together for 3 seconds.

Heater comes on High (175°) and remain on indefi-2

nitely.

Display shows SAb (See Figure 2-5).3

NOTE: Loss of power causes the Cup Warming Drawer

to exit Sabbath Mode.

Exiting Sabbath Mode

Press and hold the ON/MENU button and the1

LESS/OFF button together for 3 seconds.

Fan runs for 60 seconds and then shut off.2

Figure 2-5. Sabbath Mode

Page 9

Cup Warming Drawer (CW24)

Component Removal

3-2

#9001337 - Revision A - September, 2015

Drawer is heavy, use care not to damage drawer

slides or scratch frame of unit.

ELECTRICAL SHOCK HAZARD - DISCONNECT

ELECTRICAL SUPPLY TO UNIT BEFORE ATTEMPT-

ING THE FOLLOWING PROCEDURES.

COMPONENT ACCESS AND REMOVAL

This section explains how to access and remove components from a Cup Warming Drawer, model CW24.

An attempt has been made to arrange these procedures in such a way as to simulate which components would

need to be removed first in order to gain access to other components. When following a component removal

procedure, it may be necessary to reference another component removal procedure listed earlier in this section.

NOTE: Before continuing, please take note of the WARNINGS and CAUTIONS below.

- IF IT IS NECESSARY TO REMOVE A WARMING DRAWER UNIT FROM ITS INSTALLATION, REMEMBER

THAT THEY ARE HEAVY AND COULD FALL RESULTING IN SERIOUS INJURY. PULLING A UNIT FROM

ITS INSTALLATION SHOULD ONLY BE PERFORMED BY A TRAINED AUTHORIZED SERVICE

TECHNICIAN OR INSTALLER.

- TO AVOID ELECTRIC SHOCK, POWER TO A WARMING DRAWER UNIT MUST BE DISCONNECTED

WHENEVER ACCESSING AND/OR REMOVING COMPONENTS POWERED BY ELECTRICITY OR

COMPONENTS NEAR OTHER ELECTRICAL COMPONENTS.

- Metal edges may be sharp. Use caution when servicing unit to avoid personal injury.

- The heating element can get very hot. To avoid personal injury use caution when servicing the unit,

making sure the heater has cooled before working on or around it.

- If accessing components under the shell, the insulation must be properly reinstalled and positioned.

Failure to do so may lead to damage to the surrounding cabinetry.

- Low voltage is used for most electronic control components. To avoid damaging the appliance, DO NOT

apply 115V AC to electronic control components.

Page 10

Component Removal

Cup Warming Drawer (CW24)

3-3 #9001337 - Revision A - September, 2015

Anti-sliding Liner

To remove the anti-sliding liner, first open the cup warm-

ing drawer, then lift the anti-sliding liner by the tappered

corner located in the right rear or left front of the drawer.

Tray and Front Cover Assembly

To remove the tray and front cover assembly, first open

the cup warming drawer, then (See Figure 3-1):

1. Use a T-20 to extract two screws entering the left

and right slide horizontally.

2. Use a T-10 to extract the two screws entering the

left and right slide vertically.

3. Pull the tray and cover assembly forward and lift

from the slides.

Right and Left Slides

The right slide includes the Push To Open (PTO)

assembly. To remove either slide, first remove the tray

and cover assembly, then (See Figure 3-2):

1. Remove the unit from the installation.

2. Use a T-20 to extract the four screws on the lower

side of the cup warming drawer, on the side of the

slide to be removed.

3. Remove the slide.

Exhaust Fan, User Interface, and Exhaust

Fan Cover

To remove the exhaust fan assembly, first remove the

tray and cover assembly, then (See Figure 3-3):

1. Remove the unit from the installation.

2. Remove the power cord from the back of the unit.

3. Use a T-20 to extract the four screws on the left side

of the unit holding the exhaust fan assembly.

Figure 3-1. Screws Tray and Front Cover

Figure 3-2. Screws for Slides

Figure 3-3. Screws for Exhaust Fan Housing

Table of contents

Other Wolf Food Warmer manuals

Wolf

Wolf 30BAK-SPLH/DF User manual

Popular Food Warmer manuals by other brands

ARREDO

ARREDO Illusion 1000 instruction manual

Vollrath

Vollrath Mirage 74701DW Operator's manual

Moffat

Moffat BKRW3 Operating and service manual

Hupfer

Hupfer SPTW-2/EBF operating instructions

Kontour

Kontour K1043E installation guide

Hatco

Hatco Glo-Ray GRMW-3 Replacement parts list

HATO

HATO Macho Nacho FST-1-MN Installation and operating manual

Wittco

Wittco 500-CW Installation & operation manual

Wells

Wells SS-276ULT Specifications

Kerbl

Kerbl FastHeat Instructions for use

Johnson

Johnson Kaldino Instructions for use

Dräger

Dräger Babytherm 8004 operating instructions

APW Wyott

APW Wyott Classic RCW - 7 Installation and operating instructions

Wells

Wells BMW206ULRTD/AF owner's manual

KRATOS

KRATOS 29М-008 manual

Wells

Wells M227 Series owner's manual

Henny Penny

Henny Penny HCS-2 Technical manual

Amba

Amba RADIANT RSWH-P installation instructions