Wintal 27L05 User manual
Operating Manual
Model: 27L05
27”
16:9 Digital LCD Television/ PC Monitor
http://wintal.com.au
Manual 27L05.indd aManual 27L05.indd a 12/07/2005 11:43:31 AM12/07/2005 11:43:31 AM
Manual 27L05.indd bManual 27L05.indd b 12/07/2005 11:43:43 AM12/07/2005 11:43:43 AM
TABLE OF CONTENTS
1. PreFace 1
2. Safety Precautions 1
3. Front, Back Connections 2
4. TV Installation Guide 3
4.1 Connecting Antennas 3
4.2 AV Video Input 3
4.3 S-Video Input 3
4.4 YCbCr Connection 4
4.5 YPbPr Connection 4
4.6 PC (VGA) Connection 4
4.7 AV Video Out Connection 5
4.8 DVI Connection 5
5. Configuration 6
5.1 Picture Setting 6
5.2 AUDIO SETTING 6
5.3 SOURCE SETTING 7
5.4 TV CHANNEL SEARCH 7
6. Remote Control Instructions 8
7. Remote Control Setup 9
7.1 Battery Usage Caution 9
8. Accessories 9
9. Troubleshooting & Advice 10
10. Specifications 11
Manual 27L05.indd cManual 27L05.indd c 12/07/2005 11:43:43 AM12/07/2005 11:43:43 AM
1 | Wintal LCD
1. PREFACE
Congratulations on your purchase of a Wintal LCD! Please read this manual
thoroughly before operating the monitor. Make sure the monitor was not damaged
in transit. Should the monitor be damaged, do not install it and contact your dealer.
Check that you have all the accessories according to the model.
2. SAFETY PRECAUTIONS
Place the Monitor on a stable surface.
Do not use the monitor with other fixations than those provided or suggested by the
manufacturer.
Do not place any material on the monitor.
Do not block or cover the ventilation openings on the monitor.
If you have a wall mount, check that it is steady.
Power source
e monitor must be plugged with a voltage source of 220/240 volts and 50 Hz.
Connection cable
Power cord and cables must be properly routed and protected to prevent people from
stepping on them and causing the monitor to fall.
Heating sources and humidity
Keep the monitor dry and away from humidity.
Keep the monitor away from heat sources
Cleaning and maintenance
Unplug the monitor before cleaning it. Do not use solvents or liquids to clean the
monitor.
Only clean the monitor with a soft and dry cloth.
In case of troubleshooting, do not use spare parts other than those suggested by the
manufacturer. Using incorrect spare parts can lead to electric shocks, short-circuits
fire or other incidents.
Lightning/ Holidays
Unplug the LCD during lightning storms or when not used for long periods of time.
Manual 27L05.indd Sec1:1Manual 27L05.indd Sec1:1 12/07/2005 11:43:43 AM12/07/2005 11:43:43 AM
Wintal LCD | 2
3. FRONT, BACK CONNECTIONS
Front View and Controls
Back View
Rear Connections
AV1
AV2
PC
DVI Input Y Pb PrPC Audio
R/L Input
VGA Input Audio R/L Audio R/L S-Video
CVBS Video
Audio R/L Out
CVBS Video Out
RF In
YCbCr AV Out
Manual 27L05.indd Sec1:2Manual 27L05.indd Sec1:2 12/07/2005 11:43:43 AM12/07/2005 11:43:43 AM
3 | Wintal LCD
4. TV INSTALLATION GUIDE
4.1 Connecting Antennas
To ensure good picture and sound,TV antenna system needs to be installed. e
antenna system as shown can be sourced from TV equipment shops, which will
provide service for correct installation and connection. After installation, insert the
75-ohm antenna plug into the antenna jack as shown.
4.2 AV Video Input
4.3 S-Video Input
Manual 27L05.indd Sec1:3Manual 27L05.indd Sec1:3 12/07/2005 11:43:44 AM12/07/2005 11:43:44 AM
Wintal LCD | 4
4.4 YCbCr Connection
4.5 YPbPr Connection
4.6 PC (VGA) Connection
Manual 27L05.indd Sec1:4Manual 27L05.indd Sec1:4 12/07/2005 11:43:44 AM12/07/2005 11:43:44 AM
5 | Wintal LCD
4.7 AV Video Out Connection
4.8 DVI Connection
Manual 27L05.indd Sec1:5Manual 27L05.indd Sec1:5 12/07/2005 11:43:44 AM12/07/2005 11:43:44 AM
Wintal LCD | 6
5. CONFIGURATION
5.1 Picture Setting
Press <SYS MENU> key until the screen displays as below.
Press ►key to access image adjusting programmer. Press ▲or ▼key to select
Mode, Bright, Contrast, Colour and Sharpness for required adjusting option.
Press ◄or ►key to adjust the setting selected.
5.2 AUDIO SETTING
Press <SYS MENU> key until the screen displays as below.
Press ►key enter into audio menu press ▲or ▼key to select Mode, Volume,
Treble, Bass, Balance and Surround for required adjusting option.
Press ◄or ►key to adjust the setting selected.
a.
a.
b.
Manual 27L05.indd Sec1:6Manual 27L05.indd Sec1:6 12/07/2005 11:43:44 AM12/07/2005 11:43:44 AM
7 | Wintal LCD
5.3 SOURCE SETTING
Press <SYS MENU> key until the screen displays as below.
Press ►key to access Input Group –Blue Screen –Language—Reset menu
setting.
Press ▲or ▼key to select exact menu setting.
Select <Input Group> menu, press ►key to access TV-SCART-DVD-PC for
choose input source.
In <SCART> menu, will access to choose terminal-select in sub-menu SCART
CVBS or SCART RGB for input source.
Press ▲or ▼key to access OSD <Language>, select your language.
Press ▲or ▼key to access the <Reset> function which will reset your LCD
back to default factory settings.
5.4 TV CHANNEL SEARCH
Press <SYS MENU> key until the screen displays as below.
Press ►key to access Auto Tune – Manu Tune – Fine Tune – Sort – Add/skip–
Color System –Sound System menu setting.
Press ▲or ▼key to select exact menu setting.
Press ▲or ▼key to select <Manu Tune> or <Fine Tune > menu to adjust the
TV.
Press ▲or ▼key to access <Sort> to exchange channel.
Press ▲or ▼key to access <add/skip> to add or skip the channel.
*Before tuning in the TV, please choose the correct colour system and sound system
for your country. After that, choose the auto tune to start searching.
a.
b.
c.
d.
e.
a.
b.
c.
d.
e.
Manual 27L05.indd Sec1:7Manual 27L05.indd Sec1:7 12/07/2005 11:43:44 AM12/07/2005 11:43:44 AM
Table of contents
Other Wintal Monitor manuals
