Winco HPS9000VE/E User manual

113256-00 64854-005I

INSTALLATION INSTRUCTIONS

LOW PRESSURE FUEL SOLENOID KIT

FOR MODELS:

HPS6000HE/I, HPS9000VE/E

** For older version HPS gen-set instruction sheets go to

www.wincogen.com/service support/winco downloads/portable generators. **

COMPONENT LIST

REF. # PART # DESCRIPTION QTY.

1 42942-000 Gas Solenoid Valve 1

2 64856-006 Control Box Assembly 1

3 48039-006 Nylon Clamp 2*

4 97391-003 Tube Clamp 3**

5 479-000 Lock Washer 2

6 466-000 1/4” X 20 X 3/4” Bolt 3

7 54074-006 Pipe Nipple 1

8 49975-011 Cable Tie 3

1

2

3

4

6

5

7

8

* Not used on HPS6000HE/I and HPS9000VE/E models

** Used on HPS models prior to 2013.

213256-00 64854-005I

Install control box assembly (ref. 2) onto the frame of the gen-set (battery side) us-

ing 2 bolts (ref. 6) and lock washers (ref. 5).

Tighten with a 1/2” end wrench.

Run the cord to the rear of the generator and plug into one of the receptacles.

•

•

•

STEP 1

STEP 2 HPS6000HE/I

Thread the pipe nipple (ref. 7) onto the 90° elbow using pipe sealant.

Thread the gas solenoid valve (ref. 1) onto the pipe nipple using pipe sealant.

Make sure the solenoid end marked “OUT” is toward the generator and the

solenoid end marked “IN” is toward the supply line.

Tighten with a pipe wrench.

Connect wires labeled 1 & 21 from control box harness to the solenoid. Polarity

does not matter.

•

•

•

•

•

7

313256-00 64854-005I

Remove the bolt (A) holding the demand regulator down and rotate the demand

regulator. This allows for turning of the pipe nipple and solenoid.

Thread the pipe nipple (ref. 7) onto the 90° elbow using pipe sealant.

Thread the gas solenoid valve (ref. 1) onto the pipe nipple using pipe sealant.

Make sure the solenoid end marked “OUT” is toward the generator and the

solenoid end marked “IN” is toward the supply line.

Tighten with a pipe wrench.

Replace demand regulator bolt.

Connect wires labeled 1 & 21 from control box harness to the solenoid. Polarity

does not matter.

•

•

•

•

•

•

•

STEP 2 HPS9000VE/E

STEP 3 HPS6000HE/I

Take battery positive cable loose from starter solenoid (A). Route RED wire # 2

through the rubber cable protector (B) and re-tighten starter solenoid nut (C).

Take battery negative cable loose from engine base (D). Place BLACK wire # 1

under the bolt and re-attach battery negative cable to engine base.

•

•

C

A

B

D

A

413256-00 64854-005I

STEP 4

Using the cable ties (ref. 8) provided, neatly tie excess wire loom, wire and power

cable to prevent rubbing on the engine. HPS9000VE/E shown below.

TO START: Hold down control box button, turn key, engine will start. Once unit

generates power (about 1 second) release button.

•

•

Winco Inc.

Service Dept.

507-357-6831

STEP 3 HPS9000VE/E

Take battery positive cable loose from starter solenoid (A). Route RED wire # 2

through the rubber cable protector (B) and re-tighten starter solenoid nut (C).

Take battery negative cable loose from engine base (D). Place BLACK wire # 1

under the bolt and re-attach battery negative cable to engine base.

•

•

A

B

C

D

8

Other manuals for HPS9000VE/E

1

This manual suits for next models

1

Table of contents

Other Winco Portable Generator manuals

Popular Portable Generator manuals by other brands

Kohler

Kohler 20EORZ Operation

Powerhorse

Powerhorse 83171 owner's manual

HURST

HURST ML-630-SI instruction manual

ETQ

ETQ TG4000 owner's manual

Briggs & Stratton

Briggs & Stratton 40265 Illustrated parts list

ConMed

ConMed 7550 Service manual

Owon

Owon Waveform Generator manual

evertz

evertz 7700 Series manual

Power Stroke

Power Stroke PS906025 Operator's manual

Firefly

Firefly Cygnus CYG2400/460/24 user manual

Draper

Draper PG950S Instructions for

PowerBoss

PowerBoss PowerBoss Operator's manual

SDMO

SDMO SH 4000 Generating set user and maintenance manual

EINHELL

EINHELL STE 5500 operating instructions

Wanco

Wanco WI3000P Operator's manual

Full Boar

Full Boar FBT-3300 instruction manual

Dwyer Instruments

Dwyer Instruments ASG manual

Westinghouse

Westinghouse WH1000i Series owner's manual