WilTec ARTICEL 50800 User manual
© by WilTec Wildanger Technik GmbH Seite 6
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Operation Manual
ARTICEL 50800
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificant-
ly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH Seite 7
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
The information contained in this document is subject to change without prior notice. No part of this
document can be copied or duplicated in another form without the prior written consent of WilTec Wil-
danger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in
this user manual or the connection diagram.
Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual
is complete, accurate and updated, errors cannot always be avoided. In the event of problems with
this user manual please complete and send this form back to us.
FAX-notification (+++49 2403 55592-15),
from: ________________________________________
Name: ________________
Firm:_____________________
Tel/Fax:__________________
I would like to report the following mistakes:
___________________________________________________________________
Customer Service WilTec Wildanger Technik GmbH
e-mail: service@WilTec.info
Tel:++ +49 2403 55592-0
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury by means we urge that
our clients take some basic safety precautions when using this device. Please read the opera-
tion instructions carefully and make sure you have understood its content.
Warning! To reduce the risk of injury if you use this machine, we recommend you always to respect
the precautions, among which the following: Always read the instructions for use of this apparatus and
keep these instructions for use.
Thank you that you have this product preferred.
© by WilTec Wildanger Technik GmbH Seite 8
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
ATTENTION! Before lifting a load, make sure that you how to use this apparatus to know. The inaccu-
rate use can cause serious injury. All other uses are outlined here can be the damage to the appa-
ratus cause and be dangerous to use.
Safety application requirements
For safe use:
1. You use the mower lifts only for lifting.
2. Keep children away from lawnmowers Heber distant
3. do not let anyone approach the load because you are using the mower lift.
4. Never leave the mower lift unattended because you use this.
5. Never use the mower lift about his ability. An overload may damage the mower lift, and / or cause a
defect, causing serious injury.
6. The mower lift has been realized for a flat and hard ground. The use on a soft surface can cause
instability and can fall down the load
Always determine the load along or transverse reinforcement, which is located on the opposite side of
the Schwengeln screw. The load should always be placed horizontally are attached to the mower lift
not to damage and to prevent the load from sliding or fall down.
3. Always check the good effect from lawnmowers lifter before use. (Test only without load)
4. When it comes to a ride-on mower, make sure that the driver leave the seat has .
Image Overlay before use:
Assembly before use.
Position the jack on a lawnmower flat and stable surface
1. Expand the steel tube and fix three screws.
2. Install the handle and fix the screw.
3. Remove the locking peg.
4. Put the crankshaft upwards.
For a better use it is recommended to grease the screw before utilization.
© by WilTec Wildanger Technik GmbH Seite 9
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
1. exempt the locking clip
2. The erect dick screw
For an effective use, we recommend you only to grease the screw.
effect:
3. The locking clamp reset so that the clapper bolt remains locked upright.
4. The dick in the clockwise direction so that turning the mower lifter comes up.
The lifting of a lawnmower:
Position The mower lift on a Flacken and hard ground.
1. The mower astride put on the jack with the lower side along the transverse reinforcement pressed
(on the opposite side of the clapper screw)
,
Note: With respect to the Rider position on the back of the mower lift. The rear wheels along the trans-
verse reinforcement (5) is pressed.
2. The dick in the clockwise direction so that turning the mower lift 2 to 3 cm high comes. Make sure
the good balance of the mower on the lifter.
© by WilTec Wildanger Technik GmbH Seite 10
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
In the case of imbalance, the clapper against the clockwise direction so that the lawn mower on the
ground again, then center again by the mower forward or butt to push.
Warning: Beware not to raise too high because this may fall on the lawn mower. Do not lift higher than
necessary for the intervention.
,
maintenance
If you do not use the mower lifts .:
1. lay the dick screw
2. The screw grease regularly. This action is about every 3 months running.
3. Periodically check that there is no rust (approximately every 3 months): Clean with an oiled cloth.
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions
manual require the written permission of WilTec Wildanger Technik GmbH.
Table of contents
Other WilTec Jack manuals
WilTec
WilTec 50795 User manual
WilTec
WilTec 61336 User manual
WilTec
WilTec 61974 User manual
WilTec
WilTec 62420 User manual
WilTec
WilTec 51296 User manual
WilTec
WilTec 62367 User manual
WilTec
WilTec 61329 User manual
WilTec
WilTec 50795 User manual
WilTec
WilTec 50799 User manual
WilTec
WilTec 50797 User manual
Popular Jack manuals by other brands
Omega Lift Equipment
Omega Lift Equipment 18122C Operating instructions & parts manual
Pittsburgh
Pittsburgh 58816 Owner's manual & safety instructions
Unimec
Unimec TP Assembly instructions
Sonic
Sonic 4800703 instructions
BGS technic
BGS technic 70039 instruction manual
TradeQuip
TradeQuip 1128T owner's manual
VEVOR
VEVOR TJD-12000SP-F quick start guide
ULTIMATE SPEED
ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK operating instructions
Stels
Stels 51131 user manual
Bushranger
Bushranger RJX01 instruction manual
Clarke
Clarke CTJ2500QLG Operating & maintenance instructions
Valex
Valex 1650520 Translation of the original instructions
