Wildgame XC18i20-8 User manual
User’s Manual Model # XC18i20-8
Infrared Digital Scouting Camera
Includes
page 1
User Manual Camera Unit
Adjustable Strap
RESOLUTION
FLASH
FLASH RANGE
SENSOR
SENSOR RANGE
IMAGE FORMAT
MEMORY
IMAGE RESOLUTION
POWER SUPPLY
BATTERY LIFE
ONBOARD POWER
HOUSING
MOUNTING
MAX: 18 MP
42 High Intensity IR LED’s
up to 90 feet
Passive Infrared Sensor (PIR) Motion and Heat
up to 60 feet
JPEG - Digital Stills / AVI-Digital Video
up to 32GB SD Card (not included and required)
Class 4 and above recommended
High (18 MP)
Medium (10 MP)
Low (5 MP)
8 AA batteries (not included and required)
Alkaline recommended
Estimated up to 1 year or 30,000 photos
Built in capacitor to retain Date and Time
Weather resistant with rubber gaskets
Adjustable Strap - included
page 2
Features
Installing Batteries
1. Open the door at the bottom of the
camera by unlatching the locking
tab.
2. Locate the battery compartment
and press the “OPEN” tab to the left
to open.
page 3
3. Insert the batteries in the appropri-
ate location corresponding to the
+/- shown inside the door and above
each battery slot.
NOTE: Do not mix old and new bat-
teries. Do not mix alkaline standard
(carbon-zinc) or rechargeable (ni-
cad, ni-mh, etc.) batteries.
page 4
4. Push the latch to the left and push
the door closed to secure the bat-
teries in the compartment.
IMPORTANT:
The camera should always be turned off
before inserting or removing the SD card.
If you are using an SD card from another
camera, you must format the SD card in
your computer prior to installing it in this
camera. If you are using a new card, it does
not require any formatting prior to use in
this camera.
1. With the camera powered off, load
the SD card with the label facing up
and the grooves inserted first.
SD Card
Power On / Off
page 5
1. Press and release the power but-
ton on the main control panel.
2. A battery icon on the screen will
display the charge level. If the
batteries are properly charged,
the camera is ready for use.
+
ENTER
To turn the camera on:
1. Press and release the power but-
ton to wake up the screen.
2. Once the screen is awake, hold
down the power button until the
screen turns off.
+
ENTER
To turn the camera off:
+
ENTER
AM 12:00:30xxxxx
01/01/2017 100%
Power Save / Ready Mode
page 6
1. If no buttons are pressed for 30 sec-
onds after turning on the power, the
screen will turn off and enter Power
Save / Ready Mode.
2.LED Status Light: During the first
30 seconds of the Ready Mode, the
red light will illuminate when a PIR
event is triggered. After the LCD
turns off, the red light will blink 2-3
seconds when photo is taken.
3.After two minutes, all indicator
lights will turn off while the cam-
era continues to operate. To wake
up the LCD screen from Power Save
Mode, briefly press the power but-
ton.
+
ENTER
NOTE: The screen will not turn on
when the camera is writing to mem-
ory, and the camera will not take a
photo/video if the screen is turned
on.
Time / Date
page 7
1. The date, time and battery
charge level will display on the
LCD screen by default when it is
turned on. To change the date or
time, press “ENTER” to scroll to
the appropriate item you wish to
change (hour, minute, second,
day, month and year).
2.Use the +/- buttons to adjust
to the appropriate value. Press
“ENTER” to save and move on to
the next category.
3.Repeat steps 1 and 2 until all
fields have been updated.
AM 12:00:30xxxxx
01/01/2017 100%
+
ENTER
AM 12:15:30xxxxx
01/01/2017 100%
+
ENTER
Location
page 8
1. To save the location where this
camera is installed, use the +/-
buttons to navigate to the “Loca-
tion” screen.
2. Press “ENTER” to begin assigning
the location a name. The name can
consist of up to eight letters and/
or numbers.
Locationxxxxx
+
ENTER
+
ENTER
Locationxxxxx
F
3. Assign the desired letter/number
for each blank using the +/- but-
tons, then press “ENTER” to save
and move to the next blank.
4. When you have finished naming,
press “ENTER” until the full name
locks in place. (If you are leaving
any blanks, this may take a few
clicks.)
Locationxxxxx
FIE
+
ENTER
+
ENTER
Locationxxxxx
FIELD1
page 9
PIR Mode
1. To select the type of media your
camera captures, use the +/- but-
tons to navigate to the “PIR Mode”
screen.
2. Press “ENTER” then use the +/-
buttons to move the cursor be-
tween “Still” and “Video.”
PIR Modexxxxx
[Still] Video
+
ENTER
PIR Modexxxxx
Still [Video]
3. Once you’ve made your selection,
press “ENTER” to save.
+
ENTER
PIR Modexxxxx
Still [Video]
+
ENTER
Table of contents
Other Wildgame Scouting Camera manuals
Wildgame
Wildgame t5i20 User manual
Wildgame
Wildgame r12i20 User manual
Wildgame
Wildgame IR2 Installation and operation manual
Wildgame
Wildgame Innovations Terra Extreme User manual
Wildgame
Wildgame R12i20-7 User manual
Wildgame
Wildgame LO8 User manual
Wildgame
Wildgame Razor User manual
Wildgame
Wildgame Titan Extreme User manual
Wildgame
Wildgame Prizm User manual
Wildgame
Wildgame L20B20-7 User manual
Wildgame
Wildgame DRT Extreme User manual
Wildgame
Wildgame Innovations Mirage User manual
Wildgame
Wildgame 360 Cam User manual
Wildgame
Wildgame WRAITH User manual
Wildgame
Wildgame R12B20-7 User manual
Wildgame
Wildgame Innovations Terra 8 User manual
Wildgame
Wildgame L10b5 User manual
Wildgame
Wildgame SC20i20-7 User manual
Wildgame
Wildgame KP10B8-7 User manual
Wildgame
Wildgame Edge User manual
