WG SECURITY PRODUCT Mono-Guard User manual
58KHz Mono-Guard Transceiver System Quick Start
58kHz MONO-GUARDTM
INSTALLATION
MANUAL
WG SECURITY PRODUCT INC.
161 San Lazaro Ave. Sunnyvale, CA 94086 USA
Tel: 1-877-494-2288 (Toll Free) 1-408-530-8070 Fax: 1-408-530-8074
58KHz Mono-Guard Transceiver System Quick Start
Overview
1. System Description
Mono-Guard is a single pedestal transceiver Electronic Article Surveillance system
that detects 58KHz tags four feet either side of the pedestal. This system is plug and
play, which eliminates the need for expensive technicians during installation.
The Mono-Guard is software driven EAS system that works in combination with any
58KHz tag and label. The system’s transceiver listens for the unique signal that any
58KHz tag produces, and the sequence produced is then verified and multiplied in a
fraction of a second.
Technical DataEurope United States
Height 1470mm 58"
Width 440mm 15.5"
Depth 100mm 3.5"
Weight 10Kg 22lbs
Power 200-220vac 110vac
Operating Frequency 58kHz 58kHz
Maximum Tag Detection 2.2 meters 8 feet
IMPORTANT NOTICE:
To turn off the unit please unplug it from the main power source.
When installing this unit it is important that you follow the National Electrical Code
that governs your country.
58KHz Mono-Guard Transceiver System Quick Start
Digital Signal Processing
The Mono-GuardTM system applies the latest and most technically advanced
DSP technologies to address antitheft problems. It minimizes false alarms while
maintaining considerable detection range.
Self-Tuning Electronics
Other manufacturers need professional technicians to tune the system to
ensure proper functioning. But once the environment condition changes, the
systems best working position changes and requires tuning again. The
Mono-GuardTM system, benefiting from its fully digital electronics, constantly
detects the environment & automatically adapts to any changes. It will
always operate at its optimum performance from the beginning.
Software Driven
The Mono-GuardTM is fully digital software driven system, which allows
unprecedented flexibility especially in later versions.
Applications
This type of installation also
consists of a single Mono-
Guard
post while with coverage of a 6 foot
wide opening. The post is mounted
in the middle of the door with a 4
feet maximum detection on either
side. The Mono-
Guard can be
installed close
to a metal door or
frame with out decreasing the
detection range, how-
ever we do
recommend that the when using a
neon light, the system should be
installed 12 ft away, if this is not
possible you can install our noise
shield over the transformer to
eliminate this problem.
58KHz Mono-Guard Transceiver System Quick Start
This type of installation also
consists of a single Mono-
Guard
post while with coverage of a 6 foot
wide opening. The post is mounted
in the middle of the door with a 4
feet maximum detection on either
side. The Mono-
Guard can be
instal
led close to a metal door or
frame with out decreasing the
detection range, how-
ever we do
recommend that the when using a
neon light, the system should be
installed 12 ft away, if this is not
possible you can install our noise
shield over the transformer
to
eliminate this problem.
This type of installation consists
of one master and one slave
Mono-
Guard system with one
interconnection from slave to the
master. The gates are mounted
on both sides of the opening and
can cover a maximum range of
8 feet between the pedestals.
The Mono-
Guard can be installed
close to a metal door or frame
with out decreasing the detection
range, how-
ever we do
recommend that the when using
a neon light, the system should
be installed 12 ft away. If this is
not possible you ca
n install our
noise shield over the transformer
to eliminate this problem.
58KHz Mono-Guard Transceiver System Quick Start
Installation Procedures
Parts List
This type of installation consists of one master Mono-
Guard system and two slaves
with the master in middle and the slaves at the ends. Every gate-to-
gate distance is
both 8 feet
maximum; the three gates will cover a maximum distance of 16 feet.
Each slave post will be connected to master post.
The Mono-
Guard can be installed close to a metal door or frame with out
decreasing the detection range, how-ever we do recommend that the
when using a
neon light, the system should be installed 12 ft away, if this is not possible you can
install our noise shield over the transformer to eliminate this problem.
Base (1) Inflationary Spiral (6) Tools (2 sets)
58KHz Mono-Guard Transceiver System Quick Start
Power Cord Notices
North American Power Supply Cords
This equipment is supplied with an external power line at one end and a
molded receptacle terminal block at the other end. Conductors are color
coded white (neutral), black (line) and green or green/yellow (ground).
Operation of this equipment at voltages exceeding 130 Vac will require
power supply cords which comply with NEMA configurations.
Interconnection line (1)
Only for slave post
Bolt (2)
Gate body part (1 set)
Master or Slave Post
58KHz Mono-Guard Transceiver System Quick Start
International Power Supply Cord
This equipment is supplied with an external power line at one end and a
molded receptacle terminal block at the other end. Conductors are CEE
color coded—light blue (neutral), brown (line) and green/yellow (ground).
Other IEC 320 C-13 type power supply cords can be used if they comply
with the safety regulations of the country in which they are installed.
We recommend that you use a CE approved power cord H05 VV-F or H05 VVH2-F2
(Refer to the Electrical code which governs your country for installation of an
Anti-Theft Unit to the Main power Supply)
Attach the power cord to the field connector by following the wiring instructions below
We recommend using a power cord with a maximum length of 3 meters
L GND N
RED or BROWN = LIVE
BLACK or BLUE = NEATRAL
GREEN & YELLOW = GROUND
58KHz Mono-Guard Transceiver System Quick Start
Drill six holes (10mm diameter 40mm deep) to install the base.
Put the Inflationary spirals into the holes
Install the base, allowing the spiral heads to go through the holes of the base
Attach the cushion rings then spring rings and nuts on the spiral heads, screw the
nuts down this will fix the base to the ground.
Attach the bottom of the gate to the mount. Plug the power line into the power socket on
the PC Board as the picture shows
58KHz Mono-Guard Transceiver System Quick Start
When using a slave post, connect the interconnection cable into the RJ45
socket on PC Board
58KHz Mono-Guard Transceiver System Quick Start
There are two external alarm outputs. First press down the yellow button, then insert the
external alarm wire into the wire holding hole and release the yellow button, the wire will
be fixed onto the system. Each external alarm output has a contact rating of 1A/220VAC
The system has a switch inside the gate body with an option of 220VAC (European
system) and 110VAC input (American system), and it has been set correctly before out
from the factory.
Table of contents
