Wei Long E55 Plus User manual
E55 Plus Installation guide - Ver1.0
.
0
E55 Plus Installation Guide
E55 Plus Installation guide - Ver1.0
.
0
E55 Plus Installation guide
© 2020 Wei Long Electronics Engineering
.
All rights reserved.
Version
April 2020, Ver1.0.0
Published by
伟龙电子工程（马）有限公司
WEI LONG ELECTRONIC ENGINEERING (M) SDN BHD,
Iskandar Puteri, Johor, Malaysia.
Target Audience
Dealer, Agent, System Integrator, Buyer, Installer, Contractor.
Disclaimer
The document for general information only, in subject to any prior
revise from time to time and will be without prior notice. Wei Long
hold no responsibility on any errors or inaccuracies that may appear
in this manual.
E55 Plus Installation guide - Ver1.0
.
0
Safety Declaration
Wei Long declines any responsibility on failure, injury or death due
to improper use or use other than the use of what product is
intended or due to negligence on Good Workmanship when
installing or handling this product.
Contact us
伟龙电子工程（马）有限公司
WEI LONG ELECTRONIC ENGINEERING (M) SDN BHD
9, Jalan SILC 2/19,
79200 Iskandar Puteri,
Johor, Malaysia.
Tel
:
07-5852700
Email: malaysia@weilongelectronics.com
E55 Plus Installation guide - Ver1.0
.
0
Contents
Introduction
........................................................................................
1
Site prerequisite
.................................................................................
1
Physical Installation
............................................................................
6
Tool list
.......................................................................................
6
List of Enclosed Accessories
........................................................
7
On wall cabling
............................................................................
7
Install the Kiosk
.............................
Error! Bookmark not defined.
Attaching AC Power
.................................................................
10
Attaching LAN Network
.............................................................
11
Connect the Intercom
...............................................................
11
Analog Intercom Connection
..........................................
11
Dimension
.........................................................................................
13
Block Diagram
...................................................................................
14
Technical data
...................................................................................
16
Remarks
............................................................................................
17
E55 Plus Installation guide - Ver1.0
.
0
1
Introduction
●
This guide is intended for the installation team on-site. It serves
as a basis for the execution/processing of the installation of
one/multiple kiosk system(s) E55 Plus
.
●
All the steps for installation must be done before operating the
kiosk.
●
Wei Long Electronics Engineering technical support can be
reached on:
wlmy.support@weilongelectronics.com or XXX-XXXXXXX
Site prerequisite
Reasonable location must be selected to install E55 Plus kiosk:
●
The installation site must have the space for the E55 Plus Kiosk
enclosure. Dimensions are: 446 mm x 197 mm x 793 mm (W x L
x H) with weight of XX kg
●
The installation of E55 Plus is by wall mounting, suitable wall
surface required.
●
Visible location from parking customer. If not possible, must aid
customer with sign pointing to the kiosk.
●
Must not near any hazard and water source (eg: High Voltage,
Flammable material, Bomba water hose, Water dispenser, etc)
●
E55 Plus kiosk is non water resistant, therefore, if you are
installing outside, please install an awning or roof over the Kiosk
to protect it from rain, inclement weather and to aid screen
visibility in direct sun light.
●
Must follow wall and floor clearance for maintenance and
operation work as Figure 1.1 and Figure 1.2.
E55 Plus Installation guide - Ver1.0
.
0
2
Figure 1.1 Wall recess from top view
Figure 1.2 Floor clearance
E55 Plus Installation guide - Ver1.0
.
0
3
●
Must have wall cabling with
:
●
Incoming local LAN network coverage (CAT5e or CAT6) with
minimum speed of 100Mbps.
●
Incoming AC power (240VAC 50/60Hz) from local sub-board
with supply isolators (e.g. MCBs or fuses)
●
An incoming analog intercom system connection if required.
●
Must define the cabling path:
●
On the wall. Must guide to the cable hole on top of E55 kiosk
(see Figure 1.3)
●
From the wall. Must guide the cable into cable hole area at
the back side of E55 Plus (See Figure 1.3 and 1.4).
E55 Plus Installation guide - Ver1.0
.
0
4
Figure 1.3 Cable entry into the E55 Plus Kiosk.
E55 Plus Installation guide - Ver1.0
.
0
5
Figure 1.4 E55 Plus wall base dimension
E55 Plus Installation guide - Ver1.0
.
0
6
Physical Installation
Tool list
In addition to the standard tools, the following tools are required to
setup the E55 Plus Kiosk
:
Hammer drill with stone drill XX,
Bolt wrench XX mm (for the body mounting)
Network cable tester
RJ45 Crimper
Hammer
Table of contents
