WE-EF PSY414 User manual

WE-EF LIGHTING

Installation and Maintenance

Instructions

Bollard

PSY414 LED

PSY424 LED

PTY414 LED

PTY424 LED

Surge Protection

This product features built-in surge protection circuitry in compliance

with applicable standards.

For comprehensive protection of a luminaire installation against lightning

and electrical surges,it is essential to cover mains supply and data input

lines at the distribution board level,by using respective primary (Type 1)

and secondary (Type 2) surge arrestors in compliance with EN61643-11/

IEC61643-1.

Warning

Ensure that all required surge protection measures are in place and

activated prior to luminaire installation.Also,disconnect luminaires

before operating high-power devices such as, for example,electrical

arc welders.

Do not open during installation

This product is factory-sealed.

Refer to the instructions contained

in this document for details.

Installation tools

Mounting hardware used on this product

includes fasteners with hexalobular

socket heads (ISO 10664).Installation

requires the use of matching tools.

1

IP66/IP67, IK10,Class I, ta = 40°C

Weight lb

for PSY414 29.3

for PSY424 35.5

for PTY414 30.9

for PTY424 41.9

Accessories:

Planted root – Galvanised steel. lb

ESV2 for PSY414/424 300-9115 8.4

ESV2

Bollard

PSY414

PSY424

PTY414

PTY424

2

Light Source

LED

Maintenance

Apart from cleaning the product’s exterior surfaces,no special maintenance work is required.

Do not use high-pressure cleaners.

In case of component failure due to abnormal circumstances or at end of life, replacement must be carried

RXWE\DVXLWDEO\TXDOLĥHGDQGWUDLQHGSURIHVVLRQDO

Warning: Do not open luminaire while mains supply is switched on.

3

Installation

The product must be installed and maintained by a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW

building/construction and/or electrical regulations and relevant legislation.

Warning:6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWRLQVWDOOLQJDQGFRQQHFWLQJWKHOXPLQDLUH

Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\ZLOO

no longer be valid and shall become the full responsibility of the modifying person/organisation.

Claims based on defects attributable to improper installation and/or application, and the consequences

thereof, are excluded.

Attention: The luminaire is factory-sealed and does not need to be opened during installation.

The installation on site must comply with local and/or national health and safety regulations.

4

Installation Procedure

It is recommended to incorporate the optional planted root to ensure maximum stability.

 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\

4) Remove terminal box cover Cas shown.

2) Remove sleeve Afrom post B.

C

 3XOOFDEOHWKURXJKFHQWUHKROHDQGIDVWHQĦDQJH

plate Ewith provided fasteners to ground.

Ensure proper orientation of terminal box. An

optional planted root is available.

E

Note: Planted root installation instruction is

available in additional document.

5

6) Pull cable D(and second cable for through

wiring, if required) through strain relief(s) Fand

terminate in terminal block G.Lock cable(s) with

strain relief(s).

7) Return terminal box cover C.

C

5) Check that rating shown on luminaire label

conforms with mains electrical supply.

(example)

PSY424 120-277 / 60Hz

114-XXXX SOE XXXXXXX

LED 4000K 18W item no.XXX

08/18 IP66

8) Place sleeve Aover post Bwith sticker I

pointing up as shown.

I

A

B

G

F

D

6

10)Remove countersunk screws Jfrom head K

with Torx 25 tool (supplied by WE-EF).

9) Align sleeve ALQWRĦDQJHSODWHE

(good and bad engagement).

E

A

K

J

12)Place head Kover sleeve Aand check for

alignment.

ĦXVK

A

K

11)Hold head Kunder arm. Grab socket L,

connect and tighten with plug M.

K

M

L

7

N

-

13)Tighten recessed screws Ngradually in alter-

nating sequence 6 Nm (53.1 in-lb) with Torx

30 tool (supplied by WE-EF).

14)Return countersunk screws Jinto head and

tighten.

www.we-ef.com

WE-EF LIGHTING

United States of America

Tel +1 724 742 0030

Fax +1 724 742 0035

[email protected]

TO9245W0422 © WE-EF 2022

Technical specifications are

subject to change.

WE-EF LIGHTING

Installation and Maintenance

Instructions

Planted Root

ESV4

ESV2

ESV6

Other manuals for PSY414

1

This manual suits for next models

3

Table of contents

Other WE-EF Outdoor Light manuals

Popular Outdoor Light manuals by other brands

Sealey

Sealey LED37 instructions

nordlux

nordlux VEJERS Mounting instruction

SImx

SImx ELITE LED LHTC637 installation instructions

GEV

GEV CAROLINE 10833 manual

NEBO

NEBO NEB-LSP-0020 Use and care guide

Lindby

Lindby 9949029 Intended use

HEPER

HEPER DOGO Side LW6048.585-US Installation & maintenance instructions

HEPER

HEPER LW8034.003-US Installation & maintenance instructions

Maretti

Maretti VIBE S 14.6080.04.A quick start guide

BEGA

BEGA 84 253 Installation and technical information

HEPER

HEPER MINIMO Installation & maintenance instructions

LIGMAN

LIGMAN BAMBOO 3 installation manual

Maretti

Maretti TUBE CUBE WALL 14.4998.04 quick start guide

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB installation instructions

urban ambiance

urban ambiance UQL1273 installation instructions

TotalPond

TotalPond 52238 instruction manual

Donner & Blitzen

Donner & Blitzen 0-02661479-2 owner's manual

LIGMAN

LIGMAN DE-20023 installation manual