Watts Golden Eagle 719 Series Instruction Manual

Installation, Maintenance, & Repair

Series 719 and Series LF719

Double Check Valve Assembly

Sizes: 1⁄2" – 2" (15 – 50mm)

You are required to thoroughly read all installation instructions

and product safety information before beginning the installa-

tion of this product. FAILURE TO COMPLY WITH PROPER

INSTALLATION AND MAINTENANCE INSTRUCTIONS

COULD RESULT IN PRODUCT FAILURE WHICH CAN

CAUSE PROPERTY DAMAGE, PERSONAL INJURY AND/

OR DEATH. Watts is not responsible for damages resulting from

improper installation and/or maintenance.

Local building or plumbing codes may require modiﬁcations to

the information provided. You are required to consult the local

building and plumbing codes prior to installation. If this informa-

tion is not consistent with local building or plumbing codes, the

local codes should be followed.

Need for Periodic Inspection/Maintenance: This product

must be tested periodically in compliance with local codes, but

at least once per year or more as service conditions warrant.

Corrosive water conditions, and/or unauthorized adjustments

or repair could render the product ineffective for the service in-

tended. Regular checking and cleaning of the product’s internal

components helps assure maximum life and proper product

function.

RP/IS-719

NOTE: For Australia and New Zealand: Pipeline strainers

should be installed between the upstream shutoff valve and the

inlet of the backflow preventer.

Watts product speciﬁcations in U.S. customary units and metric

are approximate and are provided for reference only. For precise

measurements, please contact Watts Technical Service. Watts

reserves the right to change or modify product design, construc-

tion, speciﬁcations, or materials without prior notice and without

incurring any obligation to make such changes and modiﬁca-

tions on Watts products previously or subsequently sold.

1" 719QT and LF719QT

WARNING

Testing

For field testing procedure, send for IS-TK-DP/DL,

IS-TK-9A, IS-TK-99E AND IS-TK-99D.

For other repair kits and service parts, send for PL-RP-BPD.

For technical assistance, contact your local Watts

representative.

Indoors - Figure 1

Check local codes for installation requirements. Pipe lines should

be thoroughly flushed to remove foreign material before installing

the unit. A strainer should be installed as shown, ahead of backflow

preventer to prevent disc from unnecessary fouling. Install valve in

the line with arrow on valve body pointing in the direction of flow.

For indoor installations, it is important that the valve be easily

accessible to facilitate testing and servicing. Do not install in a

concealed location.

CAUTION:

Do not install with strainer when backflow preventer is used on

seldom-used water lines which are called upon during emer-

gencies, such as fire sprinkler lines, etc.

It is important that Series 719 and LF719 be tested periodically

in compliance with local codes but at least once a year or more

often depending upon system conditions. Regular inspection,

testing and cleaning assures maximum life and proper product

function.

NOTE: Fire Protection System Installations

The National Fire Protection Agency (NFPA) Guidelines require

a confirming flow test to be conducted whenever a “main line”

valve such as the shutoff valves or a backflow assembly have

been operated. Certified testers of backflow assemblies must

conduct this test. The trim valves of the confirming flow test

must be closed during the test. When the test is completed,

the trim valves must be returned to a fully open position.

Outside - Figure 2

Parallel - Figure 3

Where approved by code, Watts recommends a custom engi-

neered Watts PVS Series water supply valve station consisting of

two or more 719 and LF719 Series valves piped in parallel to serve

a larger supply main. This type of installation is employed whenever

it is required to maintain water flow to a facility. Typical applications

include hospitals, multi-family dwellings, malls and other similar

applications.

A properly designed Watts PVS valve station provides redundant

flow paths, a continuous supply of adequate water, testing and

servicing of an individual valve without supply interruption, and

long service life.

The size, quantities and design of parallel valve installations should

be exactly in accordance with the engineer’s judgment and the

published Best Practice Guide of Watts Regulator wherever pos-

sible. For a copy of the Watts Best Practice Guide, call Watts at

1-800-617-3274.

Installation Instructions

Series 719 and LF719 Double Check Valve Assemblies

719AQT

Meter Box Installation

First Shutoff

Valve

719QT-S Vertical flow-up installation

Strainer

Min. 12"

Fiberglass WattsBox

Now Available, WattsBox Insulated Enclosures.

For more information, send for ES-WB or ES-WB-T.

Figure 2

719QT-S

First

Shutoff Valve

Figure 3

First

Shutoff Valve

719QT-S

Strainer

Figure 1

Service, Replacement Parts and Maintenance

Series 719 and LF719 Double Check Valve Assemblies

Servicing the First and Second Check Valves

NOTE: Before servicing, be certain water is turned off or shutoff

valves are closed

1. Close shutoff valves up and downstream of the valve.

2. Using an appropriate sized wrench, loosen the check valve

cover. Unscrew the check valve cover and lift off.

3. Remove spring.

4. Lift out disc holder assembly from body of valve.

5. To reverse the seat disc, unscrew disc screw and disassem-

ble disc washer and disc rubber from disc holder assembly.

Reverse rubber so opposite face is showing. Assemble disc

screw through disc washer and rubber and screw into disc

holder.

6. To replace seat module, pull out of body by gripping at rein-

forcement ring. Replace seat module with new component by

placing into body seat bore. Tightening cover will engage seat

properly.

7. Insert disc holder assembly back into seat module.

8. Replace spring insuring that it seats properly on disc holder.

9. Place cover onto spring with internal guide on cover posi-

tioned inside end coil.

10. Screw cover onto valve body.

11. Tighten cover wrench tight.

10. Open shutoff valves.

Seat

O-ring

Disc Screw

Reinforcement

Ring

Seat

Disc Washer

Disc Rubber Disc Holder

Cover

O-Ring

Spring

Body

*The wetted surface of this product contacted by consumable

water contains less than 0.25% of lead by weight.

LEAD FREE*

Repair Kits

1⁄2" – 2" (15 – 50mm)

When ordering, specify ordering code number, kit number

and valve size

ORDERING CODE KIT NO. SIZE

in. mm

Total Repair Kits

0889083 RK 719-T 1⁄215mm

0889084 RK 719-T 3⁄420mm

0889085 RK 719-T 1 25mm

0889086 RK 719-T 11⁄4– 11⁄232-40mm

0889087 RK 719-T 2 50mm

Kit consists of: 2 First or Second Check Repair Kits

1st or 2nd Check Kits

0888100 RK 719R10 CK4 1⁄2– 3⁄415-20mm

0889060 RK 719 CK4 1⁄215mm

0889061 RK 719 CK4 3⁄420mm

0889062 RK 719 CK4 1 25mm

0888101 RK 719 CK4 11⁄4– 11⁄232-40mm

0888102 RK 719 CK4 2 50mm

Kit consists of: Disc holder, Spring and Cover O-ring

1st or 2nd Check Rubber Parts Kits

0888103 RK 719R10 RC4 1⁄2– 3⁄415-20mm

0889063 RK 719 RT 1⁄215mm

0889064 RK 719 RT 3⁄420mm

0889065 RK 719 RT 1 25mm

0888104 RK 719 RT 11⁄4– 11⁄232-40mm

0888105 RK 719 RT 2 50mm

Kit consists of: Disc rubber, Seat O-ring and Cover O-ring

1st or 2nd Check Seat Kits

0888997 RK 719R10 S 1⁄2– 3⁄415-20mm

0889069 RK 719 S 1⁄215mm

0889070 RK 719 S 3⁄420mm

0889071 RK 719 S 1 25mm

0888998 RK 719 S 11⁄4– 11⁄232-40mm

0888999 RK 719 S 2 50mm

Kit consists of: Seat, Seat O-ring and Cover O-ring

1st or 2nd Check Cover Kits

0888106 RK 719R10 C 1⁄2– 3⁄415-20mm

0889066 RK 719 C 1⁄215mm

0889067 RK 719 C 3⁄420mm

0889068 RK 719 C 1 25mm

0888107 RK 719 C 11⁄4– 11⁄232-40mm

0888108 RK 719 C 2 50mm

0794039 LFRK 719 C 1⁄215mm

0794040 LFRK 719 C 3⁄420mm

0794041 LFRK 719 C 1 25mm

0794042 LFRK 719 C 11⁄4– 11⁄232-40mm

0794043 LFRK 719 C 2 50mm

Kit consists of: Cover and Cover O-ring.

Note: For 11/4" 719R15 models use 11/4" – 11/2" repair kits.

LEAD FREE*

USA: Tel: (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com

Canada: Tel: (905) 332-4090 • Fax: (905) 332-7068 • www.wattscanada.ca

A Watts Water Technologies Company

Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of

original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.

THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER

WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special

or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from

labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no control.

This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.

Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above

limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to

determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.

For additional cross-connection control information, send for F-50 brochure.

Symptom Cause Solution

1. Check valve fails to hold a. Debris on check disc Disassemble and clean

1.0 PSID minimum sealing surface

b. Leaking gate valve Disassemble and clean or repair

c. Damaged seat disc or Disassemble and replace

seat o-ring

d. Damaged guide holding Disassemble clean or replace

check open

e. Weak or broken spring Disassemble and replace spring

2. Chatter during ﬂow a. Worn, damaged or Disassemble and repair or

conditions defective guide replace guide

3. Low ﬂows passing a. Mainline check fouled Disassemble and clean

through mainline

valve

b. Meter strainer plugged Disassemble and clean

c. Damaged mainline seat Disassemble and replace

disc or seat

d. Broken mainline spring Disassemble and replace

Troubleshooting Guide

Series 719 and LF719

This manual suits for next models

Other Watts Control Unit manuals

Watts

Watts POWERS HydroGuard LFG480 Series User manual

Watts

Watts AMES LF920GD Series Guide

Watts

Watts FEBCO 850 Small Series User manual

Watts

Watts AMES 981GD User manual

Watts

Watts MMV Series User manual

Watts

Watts LF1170C-M2 Series User manual

Watts

Watts LFM115-7 Owner's manual

Watts

Watts LFM116-31 Owner's manual

Watts

Watts bar-positrol Service manual

Watts

Watts LFM110-AS Owner's manual

Watts

Watts AMES LF985GD-20 Series User manual

Watts

Watts Socla BA Series User manual

Watts

Watts LFM113-12 Installation and operating instructions

Watts

Watts LFTWHG2 Series User manual

Watts

Watts FlowBox HKF25 Series User manual

Watts

Watts LFM513-6 Installation and operating instructions

Watts

Watts SENTINEL Hudrosolutions LEAK DEFENSE User manual

Watts

Watts LFM115-43 Owner's manual

Watts

Watts MS20 User manual

Watts

Watts 909 Series Installation guide

Watts

Watts USG-P-M1 User manual

Watts

Watts AMES 930GD-01-19 Manual

Watts

Watts LF70A Series User manual

Watts

Watts LF25AUB-Z3 Series Setup guide

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual