Watts AMES Deringer 50 User manual

User Guide

Deringer™

For all Deringer Series Valves

Important Installation

Information Read before

installing

For additional detailed maintenance and repair instructions,

including videos, visit BackflowDirect.com/downloads.html

For Deringer Models 20/20X/30/30X/40/40X/50/50X

Install with FLEX Couplings or Flange Adapters Only.

DO NOT use RIGID Couplings or Groove Reducing

Couplings!

Micro Bypass Orientation

Please follow these instructions to properly orient the

meters on the Deringer 30 & 50 micro bypass assemblies:

1. The Deringer water

meters are rotated 90

degrees during shipping

to protect the plastic

2. Using an adjustable

wrench loosen the meter

couplings on both sides

of the meter and rotate

the meter into the proper

orientation.

3. Using an adjustable

wrench tighten the meter

couplings on both sides

of the meter (proper

meter orientation).

Flange

Adapters

FLEX

Couplings

RIGID

Couplings

Groove Reducing

Couplings

For Deringer Models 30/30X/30G/30GX/50/50X/50G/50GX

FLOW

UserGuide-A-Deringer

WARNING: Make sure to thoroughly flush out water lines prior to installation of a Deringer. If water lines are NOT thoroughly flushed, debris will damage the check and

relief valves and will not be covered under warranty.

WARNING

Read this manual BEFORE using this equipment.

Failure to read and follow all safety and use information can

result in death, serious personal injury, property damage, or

damage to the equipment.

Keep this manual for future reference.

You are required to consult the local building and plumbing

codes prior to installation. If the information in this manual

is not consistent with local building or plumbing codes,

the local codes should be followed. Inquire with governing

authorities for additional local requirements.

WARNING

Relief Valve Installation

Please follow these instructions to properly install the relief valve to the main body:

For Deringer Models 40/40X/40G/40GX/50/50X/50G/50GX

FLOW

1. Before installing the

relief valve, make sure

the O-Ring is in the

groove on the top of the

relief valve. Apply a small

coating of lubricant to

O-Ring.

2. Mount the relief valve

to the relief valve port on

the bottom side of the

main valve body.

3. Use a 9/16” wrench

to attach the two relief

valve mounting bolts.

Tighten both bolts.

4. Use an adjustable

wrench to connect the

relief valve sensing line

to the sensing line body

coupler.

For additional detailed maintenance and repair instructions,

including videos, visit BackflowDirect.com/downloads.html

1⁄2" NPT

For Deringer Models 20/20X/30/30X/40/40X/50/50X

1. The supervisory switch assembly contains two single

pole, double throw, pre-wired switches. A primary and

an auxiliary.

2. Switch ratings:

10 amps @ 125 or 250 VAC/60 Hz

0.5 amps @ 125 VDC

0.25 amps @ 250 VDC

3. Primary and Auxilary, supervise the valve in the “OPEN”

position.

4. Primary has two #18 insulated wires per terminal, permit-

ting complete supervision of leads. Auxiliary has one #18

insulated wire per terminal. This double circuit allows for

the operation of two separate electrical devices (audible

alarms, indicating lights, etc.) in close proximity to the

valve installation.

5. A #14 insulated ground lead (green) is provided

Primary (S1) For connection to a supervisory circuit of

a UL Listed alarm control panel

Auxilary (S2) For connection to auxiliary devices per

the authority having jurisdiction

Gear Box Wiring Installation

NOTE: The below diagram shows a connection between terminals (S1: Yellow / S2: Yellow with Orange Stripe) and the normally Open

Terminals (S1: Brown / S2: Brown with Orange Stripe). In this example the signal switch will remain open (No current through switch)

as long as the valve remains Fully Opened. Once the Valve begins to close the signal switch will change from open to close (current

will flow through switch). Only S1 (two leads per terminal) may be connected to the fire alarm control panel. The connection of the

alarm switch wiring shall be in accordance with NFPA 72 and the auxiliary switch per NAPA 70 (NEC). Remember to cap off any

unused wire and that your conduit connections are water tight.

Normally Closed: (2) Blue

Normally Open: (2) Brown

Common: (2) Yellow

Normally Closed: Blue with Orange Stripe

Normally Open: Brown with Orange Stripe

Common: Yellow with Orange Stripe

For additional detailed maintenance and repair instructions,

including videos, visit BackflowDirect.com/downloads.html

Limited Warranty: Ames Fire & Waterworks (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date

of original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.

THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO

OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special

or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from

labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no control.

This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.

Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the

above limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to

determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.

USA: Backflow T: (978) 689-6066 • F: (978) 975-8350 • AmesFireWater.com

USA: Control Valves T: (713) 943-0688 • F: (713) 944-9445 • AmesFireWater.com

Canada: T: (888) 208-8927 • F: (888) 479-2887 • AmesFireWater.ca

Latin America: T: (52) 55-4122-0138 • AmesFireWater.com

Air Gap Assembly Applications & Limitations

An Air Gap Assembly (attached to relief Valve) will capture and evacuate

light to moderate water discharge from the Relieve Valve caused by daily

fluctuation in system/supply pressure.

An Air Gap Assembly will NOT capture and evacuate the

Maximum Relief Valve Discharge Rate caused by catastrophic

valve or system failure.

An auxiliary drain (separate and independent of the Air Gap Assembly) is

REQUIRED and MUST be properly sized for the Maximum Relief Valve

Discharge Rate. Ames®shall not be responsible for any damage caused

by lack of auxiliary drain, location of auxiliary drain or undersized auxiliary

drain. If the installer does not clearly understand this requirement

DO NOT install the RP/RPDA & Air Gap Assembly.

Ames Air Gaps Include:

• Air Gap drain mounting bracket

• Air gap drain shield

• Air Gap drain reducer

• All required hardware

This manual suits for next models

Other Watts Control Unit manuals

Watts

Watts AMES LF920GD Series Guide

Watts

Watts bar PZDS Operational manual

Watts

Watts LFM115-2 Owner's manual

Watts

Watts AMES 979GD User manual

Watts

Watts SENTINEL Hudrosolutions LEAK DEFENSE User manual

Watts

Watts FloodSafe WDS-SI Series User manual

Watts

Watts LFM513-14 Series User manual

Watts

Watts AMES Deringer 20G User manual

Watts

Watts IntelliFlow A2C-M1 User manual

Watts

Watts Under Sink Guardian LFUSG-B-M2 Service manual

Watts

Watts LFM114-3 Owner's manual

Watts

Watts AMES LF985GD Series User manual

Watts

Watts LFM116-31 Owner's manual

Watts

Watts tekmar Smart Boiler Control 294 User manual

Watts

Watts LF007 Series Operating instructions

Watts

Watts 909 Series Instruction Manual

Watts

Watts Tekmar Zone Valve Control 303V Series User manual

Watts

Watts bar-positrol Service manual

Watts

Watts bar PMK2 Operational manual

Watts

Watts 775 Series Installation and user guide

Watts

Watts 709 Series Operating instructions

Watts

Watts LF70A Series User manual

Watts

Watts LFM118-4 Owner's manual

Watts

Watts 757 Series Setup guide

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual