Waterway OASIS User manual
QUICK START GUIDE
810-0484.0319 ©2019 Waterway Plastics
POOL & SPA CONTROL
2200 E. Sturgis Road, Oxnard, CA 93030 • Phone 805.981.0262 • Fax 805.981.9403
Designed,
Engineered &
Manufactured
in the USA.
TRANSFORMER BOARD
GROUNDING BAR
RELAY
1. DEVICE IDENTIFICATION
• First identify which device is connected to which relay. For the purposes of this tutorial the far left relay will be used for the
Filter Pump, as it is the most common application.
• Each successive relay from the left is:
- Filter Pump
If using Filter Pump other than Waterway, High Voltage must be wired directly from Breaker. Pump will be controlled with
Low Voltage communication cable.
- Aux 1 (Water Feature, etc...)
- Aux 2 (Spa pump, etc…)
- Aux 3 (Pool Light, etc…)
- Aux 4 (Spa Light, etc...)
- Aux 5 (Cleaner, etc..)
• This order or device is not required, it is only for reference. Any Auxiliary device can be on any relay except for Relay 1 as long
as the OASIS is programmed accordingly.
Once each device and its corresponding Relay are identified, begin programming the OASIS. Please refer to the “OASIS
Instruction Manual” for installation guidance.
NOTE: Heaters are controlled with Low Voltage communication.
2. PROGRAM OASIS:
• Press Menu , and Down to highlight ‘Installer Setup’.
• With ‘Installer Setup’ highlighted press; Menu , then Up , then
Down .
• Press Right , at ‘Assign Output’.
1
• Pool Light
- Press Right at AUX1.
- Press Up to select Pool Light.
- Press Right to selection screen.
- Press Up or Down to select brand of pool light.
- Press Right to cycle to AUX2.
• Spa Light
- Press Right at AUX2.
- Press Up two times (2x) to select Spa Light.
- Press Right to selection screen.
- Press Up or Down to select ‘On/Off’.
- Press Right to cycle to AUX3.
• Blower
- Press Right at AUX3.
- Press Down twenty-three times (23x) to select Blower.
- Press Right to selection screen.
- Press Down to select ‘Spa’.
- Press Right to cycle to AUX4.
• Cleaner
- Press Right at AUX4.
- Press Down nineteen times (19x) to select Cleaner.
- Press Right to selection screen.
- Press Down to select ‘Pool’.
- Press Right to cycle to AUX5.
3. ASSIGN OUTPUT:
• Filter Pump
- Press Right , and Up or Down to select the type of pump. For this guide,
select ‘1 Speed’.
• J1 Intake
- J1 Intake, J2 Return, J3 Solar, and J4 Option are designed to control the Actuator valves
that can be connected to J1, J2, J3, or J4 respectively on the board.
- With J1 Intake highlighted, press Right , then Up or Down to select the use for the actuator.
- NOTE: When J1 is set to ‘Intake’, J2 automatically sets to ‘Return’. This setting sets the OASIS for Pool/Spillover/Spa modes.
• AUX 1, 2, 3,…
- AUX 1 is for Relay 2 in most configurations. With AUX 1 highlighted, press Right , then Up or Down to choose
the device.
- Once a device has been chosen, pressing Right will move to a selection screen showing options for that type of device.
(Type of LIGHT that can be chosen; On/Off, IntelliBrite, Jandy Color, Jandy LED, Color Logic).
- Other devices can be assigned to: None, Pool, Spillover, or Spa mode. This will put the OASIS in that Mode when the device is
turned on.
- Pressing Right again will cycle down to the next AUX device. Or Left can be pressed to move to the
previous screen.
2
Blower
Blower
5. FREEZE PROTECT:
• Press Menu , and highlight ‘Installer Setup’.
• With ‘Installer Setup’ highlighted press: Menu , then Up , then Down .
• Press Down to select ‘Freeze Protect.
• Press Right to select.
• Press Right to highlight ‘Enable’.
• Press Up or Down to ‘Enable’ or ‘Disable’ Freeze Protection.
• Press Right 2 times to highlight ‘40’, the default Freeze Protect temperature.
• The Up or Down arrows can be used to adjust this setting.
• When adjustments are made, press HOME to return to the main screen.
810-0484.0319 ©2019 Waterway Plastics
2200 E. Sturgis Road, Oxnard, CA 93030 • Phone 805.981.0262 • Fax 805.981.9403
Designed,
Engineered &
Manufactured
in the USA.
4. RESTART OASIS:
• When all Devices have been assigned, move selection up to ‘Filter Pump’, then press Left . The OASIS will restart when
applying the new settings.
For more information on configuring/programming the OASIS, use the QR code below or visit
www.youtube.com/watch?v=gInl5vTJCYQ&t
Other manuals for OASIS
2
Other Waterway Spa Accessories manuals
