Wasp WWS110i User manual
1
WWS110i
Quick Start Guide
Table of Contents
Quick Start 2
1. Unpack 2
2. Charging the WWS110i 2
3. Connecting the Scanner to a Bluetooth Device 2
Setup & Configuration 6
Factory Default 7
Check Version 7
Link Quality On/Off 7
Set Connection 7
Bluetooth SPP (Bluetooth COM) 8
Bluetooth HID (Keyboard) 8
Start and Stop Pin 8-9
Terminator 10
iPad/iPhone Toggle Keyboard 10
Secure Simple Pairing 11
QSG
2
QSG
2
Quick Start
1. Unpack
Open the box and remove all the pieces from their protective packaging.
2. Charging the WWS110i
You must charge the scanner for 4 hours before first using it. To charge
the scanner, plug the power supply into the bottom of the scanner.
3. Connecting the scanner to a Bluetooth device
The scanner will connect to most Bluetooth devices that support HID
connection.
You will need to open your Bluetooth software and search for Bluetooth
devices. The Bluetooth software can be found by clicking the Bluetooth
symbol on the start bar near the computer time. If the Bluetooth symbol is
not found, there could be a problem with the Bluetooth adapter installation.
QSG
2 3
QSG
32
Check the “My device is setup and
ready to be found” checkbox and click Next.
The scanner will show up in the list of
Bluetooth devices found. Select
Wasp Barcode and click Next.
If Wasp Barcode does not show up in the
available devices, check the following:
1. Make sure the scanner is on by pressing
the trigger.
2. If you are using a pre-installed Bluetooth
adapter, make sure the adapter supports HID.
Windows XP Bluetooth Pairing
Scan the following three barcodes:
1. Factory Default - page 7
2. Bluetooth HID - page 8
3. Set Connection - page 7
The next step will ask you to setup a passkey
for the device.
Select “Choose a passkey for me”, then click
the Next button. Your passkey will appear on
the resulting screen.
QSG
4
The Complete Wizard screen appears. Click
Finish to complete.
When the wizard is complete, the scanner
will show up as a Wasp Keyboard. Click OK
to close the screen. You are now ready to
use the WWS110i.
Scan the following barcodes found on page 9:
Note: Maintain a brisk pace when scannng these codes, as Windows
provides a short time for entering them.
1. Start PIN
2. Each digit of the code
3. Enter
4. Stop PIN
Windows 7 Bluetooth Pairing
Click the Start icon, then type “bluetooth” in
the Search field.
Click “Add a Bluetooth device” from the
resulting menu choices.
Scan the following three barcodes:
1. Factory Default - page 7
2. Bluetooth HID - page 8
3. Set Connection - page 7
QSG
QSG
4 5
Click Wasp Barcode Bluetooth Keyboard,
then click the Next button.
Scan the following barcodes found on
page 9:
Note: Maintain a brisk pace when scannng
these codes, as Windows provides a short
time for entering them.
1. Start PIN
2. Each digit of the code
3. Enter
4. Stop PIN
A screen will appear confirming you have
successfully added the scanner.
When the wizard is complete, the scanner
will show up as a Wasp Keyboard. Click OK
to close the screen. You are now ready to
use the WWS110i.
QSG
QSG
6
In order to configure Wasp WWS110i Freedom Scanner, familiarize
yourself with the setup procedures on the following pages. The default
settings of the scanners are identified on each page and clearly marked
using an asterisk (*). The default settings have been preprogrammed for
the most common barcode configurations. Use the setup & configuration
barcodes only to customize the WWS110i Freedom Scanner settings. If
you need to configure the Scanner, the default settings will be overwritten.
All the programmed settings are stored permanently in non-volatile
memory.
In order to configure Wasp WWS110i Freedom Scanner,
two basic steps need to be followed:
(1) Locate the group that contains the options to be changed.
(2) Scan the barcode representing the option to be changed.
The scanner will sound two beeps.
Setup & Configuration
QSG
76
Use the Factory Default barcode to reset the scanner to the Default settings.
Factory Default
Check Version
Scan the Check Version barcode to verify your current firmware’s version number.
Check Version
Factory Default
Link Quality affects the transmission quality. When Link Quality is turned
on (default setting), data transfer is more secure, but slower. If you notice
that your transmissions to the host are too slow, you can try turning the
Link Quality setting to off.
Link Quality On/Off
Link Quality On* Link Quality Off
Set Connection
Scan this barcode to break your current connection and enable your device
to connect to a new Bluetooth host.
Set Connection
QSG
8
Bluetooth SPP (Bluetooth COM)
The Bluetooth SPP (Serial Port Protocol) creates a virtual Bluetooth
comport. This setting is not recommended. Only use this option if you
have software capable of capturing data off of a comport.
Bluetooth SPP (Bluetooth COM)
Bluetooth HID
Use this setting (on by default) to pair with most Bluetooth connections.
Bluetooth HID works just like a keyboard.
Bluetooth HID*
Start and Stop Pin
Use the Start and Stop Pin barcodes when you are prompted for a password
(Passkey) during Bluetooth pairing. To use this setting:
1. When prompted for a password, scan the Start Pin barcode.
2. Scan the appropriate numbers (provided on page 9) for your password.
3. Scan ENTER.
4. Scan the Stop Pin barcode.
Now the Pin is set and the scanner should pair to the PC. Test the
connection by scanning a barcode into WordPad, NotePad or the equivalent
and verifying the scan is correct.
QSG
9
connection
8
Start Pin
Stop Pin
ENTER
Other manuals for WWS110i
1
This manual suits for next models
1
Table of contents
Other Wasp Barcode Reader manuals
Wasp
Wasp WWS800 User manual
Wasp
Wasp WPL205 User manual
Wasp
Wasp WLS8600 User manual
Wasp
Wasp WDI9600 User manual
Wasp
Wasp WPL25 User manual
Wasp
Wasp WPL608 User manual
Wasp
Wasp WWS550i User manual
Wasp
Wasp Wasp WDI7500 Installation and operation manual
Wasp
Wasp WWS550i Installation guide
Wasp
Wasp WLR8950 User manual
