wallas 2000t Manual
10L
5L
2413
2411
2410
2412
2467
2448
2460
28/45mm
MAX 2m
2000t,
MAX 6m
6m
6,2
kg
60
1,55m
2000t
12V
- 67 -
2000t
1
2
3
4
5
7
8
9
10
12
6
11
13
en
Mounting bolt M8 x 120 mm DIN 931 / ISO 4014
Corrugated base plate M8 DIN 137 A
Hose binder 32 - 50 mm
Fuse box
2 pcs
2 pcs
1 pcs
1 pcs
Heater (fuel hose and control panel cable installed)
Accessory bag 17662B
Mounting plate
1 pcs
1 pcs
1 pcs
1 pcs
2 pcs Push on contact 6.3 x 0.8 (yellow)
Fuse 15 A (blue)
Fastening screw 4,8 x 16 mm DIN 7981 / ISO 70496 pcs
Installation, operation and maintenance instructions1 pcs
Control panel
Control panel fastening screws 3,5 x 20 mm (black) TX10
Control panel package 3610661 pcs
1 pcs
4 pcs
Hose binder 50 - 70 mm2 pcs
Extension collar1 pcs
Control panel fastening screws 3,5 x 40 mm (black) TX104 pcs
Package contents
2000t
Technical information
D10431
490603
- 68 -
12 V DC
2000t
0,4- 0,7 A
0,10- 0,20l/h
900 W
2000 W
2 x ø 60 mm
en
Fuel Parafn
6,2 kg
13,7 lbs
Operating voltage
Fuel consumption
Heating power, max
Power consumption
Dimensions (L x H x W)
Weight
Maximum permitted length of
exhaust pipe
Maximum permitted length of
fuel hose
Minimum area of the replacement air
opening
Suitable Exhaust gas lead-throughs
Technical information
2467 and 2460
Heating power, min
Maximum permitted length of
warm air duct
Warm air connection
Remote control
Timer
Connections
364 x 260 x 126 mm
14 3/8“ x 10 1/4” x 5”
8 m
26’
100 cm2
16squareinches
6+ 6m
2 m (ø 28/45 mm)
6,5’ (ø 28/45 mm)
(when ignited ca. 2 min. 5 A)
2000t
Technical information
D10431
490603
- 69 -
en
Operation description
The 2000theatersareforcedairParaffinheaterswithoutanexposedflame.
The 2000t models take combustion air from outside the boat through the outer
coaxial exhaust gas pipe and blow their exhaust out through the inner coaxialpipe.
Thecoaxialpipeconnectstoacommonthroughhullfittingthatallowsbothinletair
andexhausttopassseparately.Thisprocessimprovesefficiency,wind resistance
and lowers the minimum power level.
The heat generated by forced air fuel combustion, is transferred to the circulation
air by a heat exchanger. The heating power can be adjusted freely between high
and low output settings by manual rheostat control or by thermostat.
The heated air is circulated through the cabin through the warm air ducting.
In hot and/or humid conditions, these heating units can be used for simple fresh air
ventilation and circulation.
When starting the device, the glow plug ignites the pumped fuel in the burner bowl.
Theglow/startandshutdownsequencesarefactoryprogrammed,so-startsand
stops are automatically controlled.
The fuel pump inside the heater case regulates the fuel feed and the system
electronics control both the fuel and air mixture to maintain the ideal clean burning
process. The temperature sensor inside the burner feels the ignition and lights up
the red signal light (1) to indicate a successful start. When stopping the device, an
automatic after cooling process takes place. This process cleans the burner, purg-
ing any unburned fuel.
The heaters are completely made out of corrosion resistant materials.
2000t
Installation
D10431
490603
- 70 -
en
Heater installation
Countryspecicregulationsshallbefollowedinanyinstallation.
The warranty of boat products is valid only in boat installations.
The warranty is not valid in installations to vehicles or other spaces.
The device is meant for marine pleasure craft use. The device is not designed for
continuous use for example in live aboard boats or commercial settings. In such
usethedevicewillrequiremorefrequentservicingnotcoveredbywarranty.
Things to note when selecting the installation location
The device shall be installed into a dry space in a protected location.
The device must be mounted to a solid, stable bulkhead or wall.
When installing, please note that the device needs to be removable for servicing.
Connections and location should be made so that the device can be easily discon-
nected for removal. For maintenance, it is useful to leave 200 mm (7 7/8”) empty
space below the heater for the removal of the bottom cover of the heater.
The heater should be installed vertically level when the boat is on an even keel.
The static inclination must not exceed 5°. While the device will tolerate being
temporarily tilted to a steep angle (even for some hours), the burner will not yield
optimal performance if it is constantly inclined.
Please note specially the following things:
•Avoid installing the control panel in the immediate vicinity of a water outlet.
•If possible, install the control panel on a vertical surface.
•Select the place of installation to allow a minimum amount of bending in the
warm air ducting.
We recommend that the device be installed by an authorized Wallas service shop
or installer.
Things to note when installing pipes, hoses and cables
Power cables, warm-air ducting and fuel hoses must be protected in locations
where they are susceptible to mechanical damage due to sharp edges or heat.
Allcablesandhosesshouldhaveauidprecluding“driploop”topreventwateror
otheruidsfromfollowingwiresorhosestotheheater.
Installation space
The device can be installed within the heated space or outside of it.
The heater cannot be installed into a space which may include
gasoline fumes (danger for explosion).
2000t
Installation
D10431
490603
- 71 -
13 mm ø 35 / ø 50 mm
ø 60 mm
ø 67 mm
ø 2 mm
ø 5 / ø 6 mm
PZ 2
PH 2
TX 10
en
The necessary installation tools
Always use original Wallas accessories and parts with Wallas
equipment.
In a metal-hulled boat, you must ensure that the device, the exhaust
gas lead-through, the fuel connection, the control panel, and all other
parts are insulated from the boat’s hull. This must be done to
•prevent electrochemical corrosion
•prevent voltage from being transmitted from the hull to the device
or vice versa during electrical faults.
2000t
Installation
D10431
490603
K00038
K00101
- 72 -
1
5
23
4
en
Fastening the device
Fix the mounting plate (1) with screws (4) to a suitable place and check that the
bottom of the heater is in horizontal position.
Lift the heater into the installation plate and lock the device with the mounting bolts
(2). There has to be a corrugated base plate (3) under the head of the screw. Be
surethattheedgeofthemountingplatewilllocktotheslotinthesideproleofthe
heater.
Connect the exhaust gas pipe with a hose clamp (5).
2000t
Installation
D10431
490603
- 73 -
en
2000t
Installation
D10431
490603
K00114
- 74 -
ø 2 mm (3/32’’)
100 mm (3 15/16’’)
65 mm (2 9/16’’)
17,5 mm
(11/16’’)
4,5 mm (11/64’’)
47 mm (1 27/32’’)
56,1 mm (2 13/64’’)
10 12
17,5 mm
(11/16’’)
69 mm (2 23/32’’)
104 mm (4 3/32’’)
en
Control panel installation
Cut a suitable installation hole for the control panel in the selected location. Try to
install the panel in a vertical surface in a location that will remain dry.
Measurements of the control panel installation cut-out.
If necessary, predrill holes for the ø 2 mm ( 3/32”) screws.
You can utilize the sample of the box when drawing the lines of the
installation hole.
Connect the control panel cable from the device to the control panel (10).
Use the fastening screws to install the control panel to the installation cut-out (12).
The thermostat sensor is in the panel face, so select the location
with thermostatic operation/regulation in mind. Do not install close
to heat source or close to a window or door. Avoid locations that
might be contacted by direct sunlight. The length of the control
panel cable is 6 m.
2000t
Installation
D10431
490603
K00143
K00144
- 75 -
11
13
en
An extension collar (11) is used when control
panel is surface mounted.
The box of the panel includes 4 pcs screws 3,5
x 40mm (black) TX10 (13).
When installing the control panel surface
mounted (using the collar) , a loop to the
control panel cabel must be done. A cable
tie must be attached to cable in order to
avoid the cable detach from the connec-
tor.
Connections of the device
Things to note about the connections
In installation, to make the mounting and demounting for service easier, it is recom-
mended to leave some extra length of loose cables and fuel line by creating a coil.
WARM AIR
OUT
EXHAUST
OUT
COMBUSTION AIR
IN
2000t
Installation
D10431
490603
K00114
- 76 -
0 - 4
4 - 6
6 - 10
4 (11 or 10 AWG)
6 (9 or 8 AWG)
10 (7 or 6 AWG)
en
Electrical connections
Things to note about the connections
The device uses 12V (nominal) direct current voltage. To minimize current losses,
make the power cable as short as possible and avoid joining. The cross-sectional
area of the cable is dependent on the length of the power cord. The cross-sectional
area of the cable must be consistent all the way from the stove to the battery. The
maximum length of the power cord is 10 m.
Total length of the power cord (m) Cross-sectional area of the cable in square mm
(US Gauge)
Ifathickercableisrequired,makeaseparatejointinthepowercord.Seepicture
on the next page.
Main switch
A main switch (accessory) must be installed on the device’s “positive (Red)” cord.
Always cut the power at the main switch (after cooling has completed), if the device
is going to be left unused for a long period of time.
Never use the main switch to cut the power before the cooling phase,
which starts after the device is turned off, is completed.
The cross-sectional area of the cable
Remote control (accessory)
Timer (accessory)
Accessories are connected to the control
panel, the image shows the place.
Take care of the strain relief.
2000t
Installation
D10431
490603
Table of contents
Other wallas Heater manuals
wallas
wallas Spartan Manual
wallas
wallas Nautic 40D Installation guide
wallas
wallas 26CC User manual
wallas
wallas 22 GB User manual
wallas
wallas M40 Manual
wallas
wallas 1300 User manual
wallas
wallas Spartan User manual
wallas
wallas 26CC User manual
wallas
wallas 2400 t User manual
wallas
wallas 30 GB User manual
Popular Heater manuals by other brands
oventrop
oventrop Regucor Series quick start guide
Blaze King
Blaze King CLARITY CL2118.IPI.1 Operation & installation manual
ELMEKO
ELMEKO ML 150 Installation and operating manual
BN Thermic
BN Thermic 830T instructions
KING
KING K Series Installation, operation & maintenance instructions
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Installation instructions and owner's manual
Empire Heating Systems
Empire Heating Systems WCC65 Installation and owner's instructions
Wetekom
Wetekom 92 86 43 Original instructions
Desa
Desa SPC170-F owner's manual
Watlow
Watlow Watrod Electric Tubular Heaters Specifications
Haverland
Haverland ECO-DRY GPS Series Instruction & installation manual
Stelpro
Stelpro ASILVC2060 Series user guide