WAGNER W 125 User manual

wagner-group.com

WOOD & METAL SPRAYER

W 125

OPERATING INSTRUCTIONS

AUS

W 125





1/2

W 125

A B C





5-15 cm





2

3

W 125

i

1

W 125 GB

Contents

1. Explanation of symbols used .....................................................5

2. General Safety Instructions ......................................................5

3. Safety Instructions for Spray Guns ...............................................8

4. Description/ Scope of delivery ...................................................9

5. Coating Materials ................................................................9

6. Start-up .........................................................................9

7. Adjusting the desired Spray Setting ..............................................9

8. Adjusting the Material Volume (Fig. 5) ..........................................10

9. Spray Technique ...............................................................10

10. Taking Out of Operation and Cleaning.........................................10

11. Maintenance ................................................................. 11

12. Spare Parts List ...............................................................11

13. Correction of Malfunctions....................................................11

14. Technical Data................................................................12

15. Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

16. Important Note regarding Product Liability! ................................... 13

Translation of the original operating instructions

1. Explanation of symbols used

This symbol indicates a potential danger for you or for the device.

Under this symbol you can nd important information on how to

avoid injuries and damage to the device.

Danger of electrical shock

Indicates tips for use and other particularly useful information.

2. General Safety Instructions

Caution! Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refer to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

W 125GB

1. Safety at the workplace

a) Keep your workplace clean and well lit. Disorder or unlit workplaces may result in

accidents.

b) Never use the tool in hazardous areas that contain ammable liquids, gases or

dusts. Power tools generate sparks that can ignite the dust or vapors.

c) Keep children and other persons away when using the power tool. You can lose

control of the tool if you are distracted.

2. Electrical Safety

The tool plug must t into the socket.The plug may not be modied in any form.

Do not use adaptor plugs together with protective-earthed tools. Unmodied

plugs and suitable sockets reduce the risk of an electric shock.

b) Avoid physical contact with earthed surfaces such as pipes, heating elements,

stoves and refrigerators. The risk through electric shock increases if your body is

earthed.

Keep the equipment away from rain and moisture. The risk of an electric shock

increases if water penetrates electrical equipment.

d) Do not misuse the mains lead by carrying the tool by the lead, hanging it from

the lead or by pulling on the lead to remove the plug. Keep the lead away from

heat, oil, sharp edges or moving tool parts. Damaged or twisted leads increase the

risk of an electric shock.

e) If you work outdoors with a power tool, only use extension cables suitable for

outdoor use. The use of an extension lead that is suitable for outdoors reduces the risk

of an electric shock.

If you cannot avoid using the tool in a damp environment, use a residual current

operated circuit-breaker. Using a residual current operated circuit-breaker avoids the

risk of electric shock.

3. Safety of Persons

Be attentive. Pay attention to what you are doing and work sensibly with a

power tool. Do not use the tool if you are tired or under the inuence of drugs,

alcohol or medication. Just a moment of inattentiveness while using the tool can lead

to serious injuries.

Wear personal safety equipment and always wear safety goggles Wearing

personal protective equipment, such as dust mask, non-slip safety shoes, safety helm

or ear protection, depending on the type of power tools, reduces the risk of injury.

W 125 GB

Avoid accidental starting-up. Make sure that the electric tool is switched o

before you connect it to the power supply, pick it up or carry it. Accidents can

occur if you carry the power tool while your nger is on the switch or if you connect the

power tool to the power supply which it is on.

d) Remove setting tools or wrenches before switching on the power tool. A tool

or wrench that is in a rotating tool part can lead to injuries.

Avoid an unnatural posture. Ensure that you are standing securely and have your

balance at all times. This ensures that you can control the tool better in unexpected

situations.

f) Wear suitable clothing. Do not wear wide clothing or jewellery. Keep your hair,

clothes and gloves away from moving parts. Loose clothing, jewellery or long hair

can be caught in moving parts.

Do not lull yourself into a false sense of security and do not think yourself above

the safety rules for electric tools, even if you are familiar with the electric tool

following extensive practical experience. Careless use can lead to serious injuries

in fractions of a second.

4. Usage and treatment of the electric tool

a) Do not overload the tool. Use the power tool designed for the work that you

are doing. You work better and safer in the specied performance range if you use the

suitable power tool.

Do not use power tools whose switch is defective. A power tool that cannot be

switched on or o is dangerous and has to be repaired.

c) Remove the plug from the socket before carrying out tool settings, changing

accessories or putting the tool away. This precautionary measure prevents

unintentional starting of the tool.

d) Store unused power tools so that they are inaccessible to children. Do not let

persons use the tool who are not familiar with it or who have not read these

instructions. Power tools are dangerous when they are used by inexperienced persons.

Take proper care of your tools. Check whether the moving parts function

trouble-free and do not jam, whether parts are broken or damaged so that

the tool function is impaired. Have damaged parts repaired before using the

tool. Many accidents have their origin in power tools that have been maintained badly.

Use the power tool, accessories, insert tools, etc. in accordance with these

instructions and in a fashion specied for this special tool type.Take the working

conditions and the activity to be carried out into consideration. The use of power

tools for purposes other than the intended ones can lead to dangerous situations.

W 125GB

Keep the handles and grip surfaces dry, clean and free of oil and grease. Slippery

handles and grip surfaces hamper safe operation and control of the electric tool in

unforeseen situations.

5. Service

Have your tool repaired only by qualied specialist personnel and only with

original spare parts. This ensures that the tool safety is maintained.

b) If the supply cord is damaged, it must be replaced by the manufacturer or it’s

service agent or a similarly qualied person in order to avoid a safety hazard.

3. Safety Instructions for Spray Guns

•

The device may not be used in workplaces covered by the explosion-protection

regulations.

•

There must be no sources of ignition such as, for example, open res, smoke of lit

cigarettes, cigars and tobacco pipes, sparks, glowing wires, hot surfaces, etc. in the

vicinity during spraying.

•

Do not spray any substances whose hazard potential is not known.

•

Before working on the spray gun remove the power plug from the socket.

•

Do not use the spray guns to spray ammable substances.

•

The spray guns are not to be cleaned with ammable solvents.

•

Caution against dangers that can arise from the sprayed substance and observe the

text and information on the containers or the specications given by the substance

manufacturer.

•

Caution! Wear breathing equipment: Paint mist and solvent vapors are damaging to

health. Always wear breathing equipment and only work in well ventilated rooms or

using supplementary ventilating equipment. It is advisable to wear working clothing,

safety glasses, ear protection and gloves.

CAUTION: DANGER OF INJURY!

Never point the spray stream towards human beings or animals.

Sockets and plugs must be masked. Risk of an electric shock as a

consequence of sprayed material entering the socket!

•

When working with theW 125 indoors as well as outdoors ensure that no solvent vapors

are sucked in by the spray gun.

•

When working outdoors, be aware of the wind direction. Wind can carry the coating

substance across greater distances - thus causing damage.When working indoors, provide

for adequate ventilation.

•

Do not let children handle the device.

•

Never open the device yourself in order to carry out repairs in the electrical system!

With original Wagner accessories and spare parts, you have the guarantee that all

safety regulations are fullled.

W 125 GB

4. Description/ Scope of delivery

Description/ Scope of delivery (Fig. 1)

1) Air Cap 2) Nozzle

Union nut with material volume regulation

4) Trigger

5) ON/OFF switch 6) Air lter

7) Container

5. Coating Materials

Coating Materials Suitable for Use

Glazes, Wood preservatives undiluted

Paints containing solvents and water-soluble paints, primers dilute by 5 - 10%

Coating Materials Not Suitable for Use

Wall paints, materials that contain highly abrasive components, facade paint, caustic

solutions and acidic coating substances. Flammable materials.

Paints, varnishes and glazes can be sprayed undiluted or slightly diluted.Paints, varnishes and glazes can be sprayed undiluted or slightly diluted.

1. Stir the material up and put the required amount into the paint container.

2. If the convey capacity is too low, add 5 - 10% dilution step-by-step until the convey

capacity fulls your requirements.

6. Start-up

Before connecting to the mains supply, be sure that the supply voltage is identical with

the value given on the rating plate.

•

Unscrew the container from the spray gun.

•

Aligning suction tube. (Fig. 2)

If the suction tube is positioned correctly, the container contents can be sprayed

without almost any residue.

When working on lying objects: Turn the suction tube forwards. (Fig. 2 A)

Spraying work when working on overhead objects: Turn the suction tube rearwards.

(Fig. 2 B)

•

Set the container on a sheet of paper, pour in the prepared coating material and screw

the container tightly onto the spray gun.

7. Adjusting the desired Spray Setting

WARNING! Danger of injury! Never pull the trigger guard while adjusting

the air cap.

Turn the air cap (g. 3, 2) to the desired spray setting position (arrow).

W 125GB

Fig. 4 A = vertical at jet for horizontal surfaces

Fig. 4 B = horizontal at jet for vertical surfaces

Fig. 4 C = circular jet for corners, edges and hard-to-reach surfaces

8. Adjusting the Material Volume (Fig. 5)

Adjust the volume of material by turning the union nut from 1 - 8.

9. Spray Technique

•

The spray result depends heavily on the smoothness and cleanliness of the surface to be

sprayed. Therefore the surface should be carefully prepared and kept free of dust.

•

Cover all surfaces not to be sprayed.

•

It is advisable to test the spray gun on cardboard or a similar surface to nd the correct

setting.

Important: Begin spraying outside of the target area and avoid interruptions inside the

target area.

•

Correct (Fig. 6a) Be sure to hold the spray gun at an even distance of approx. 5 - 15 cm

to the target object.

•

Incorrect (Fig. 6b) Heavy spray fog build-up, uneven surface quality.

10. Taking Out of Operation and Cleaning

Proper cleaning is the prerequisite for problem-free operation of the paint application

device. No warranty claims are accepted in case of improper or no cleaning. When

processing 2-component varnishes, clean the device immediately.

WARNING! Never hold the spray gun rear part under water or immerse it

into liquids. Clean the housing only with a moistened cloth.

1) Turn o the machine and remove the plug.

2) Unscrew the container. Empty any remaining coating material back into the material

tin.

3) Pull out the suction tube with container seal.

4) Turn the union nut (Fig. 7, 1) beyond the lock at level 1 to remove it. Remove the air

cap (2) and pull out the front section of the gun (3). Pull the nozzle (4) out of the front

part of the spray gun.

CAUTION! Never clean the spray gun with metal objects.

Clean all parts carefully using a brush and water or solvent (depending on the material

being processed). Take particular care to ensure that the ventilation hole (Fig. 8) is

clear.

Assembly

1)1) Insert the nozzle (Fig. 9) into the gun body so that the slots in the nozzle engage inInsert the nozzle (Fig. 9) into the gun body so that the slots in the nozzle engage in

Other manuals for W 125

Table of contents

Other WAGNER Paint Sprayer manuals

WAGNER

WAGNER ProjectPro 117 User manual

WAGNER

WAGNER Power Painter User manual

WAGNER

WAGNER PS 3.20 User manual

WAGNER

WAGNER ProSpray 22 User manual

WAGNER

WAGNER W 570 FLEXIO User manual

WAGNER

WAGNER Power Painter User manual

WAGNER

WAGNER W 670 User manual

WAGNER

WAGNER Super Finish 23 PLUS User manual

WAGNER

WAGNER PEM-X1 CG Operational manual

WAGNER

WAGNER Flexio 3000 User manual

WAGNER

WAGNER Super Finish 23 PLUS User manual

WAGNER

WAGNER Control Stainer 150 User manual

WAGNER

WAGNER W 300 User manual

WAGNER

WAGNER Airless Sprayer Plus 0418 User manual

WAGNER

WAGNER FLEXiO 990 User manual

WAGNER

WAGNER PLASTCOAT 1030 User manual

WAGNER

WAGNER CONTROL SPRAY User guide

WAGNER

WAGNER ProSpray 3.21 Installation instructions

WAGNER

WAGNER Super Finish 21 User manual

WAGNER

WAGNER ProSpray 3.23 User manual

WAGNER

WAGNER WallPerfect W665 Installation guide

WAGNER

WAGNER HEAVYCOAT HC730 GAS User manual

WAGNER

WAGNER Control Pro 150 User manual

WAGNER

WAGNER WallPerfect W 565 Quick guide

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Nordson

Nordson MicroMax 2 manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual