Vuescape 11009588 User manual
19˝ Widescreen
Flat Panel TFT/ LCD Monitor
Item Number: 11009588
Installation & User’s Manual
All brand names and trademarks are the property of their respective owners
* Important Notice: Please read this manual carefully
2
FCC Radiation Norm
FCC
This equipment has been tested and complies with limits for Class B digital devices pursuant to
Part 15 of Federal Communications Commission (FCC) rules.
FCC Compliance Statement
These limits are designed to provide reasonable protection against frequency interference in
residential installations. This equipment generates, and radiates radio frequency energy, and if
not installed properly or used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not
occur in television reception, which can be determined by turning the equipment on and off.
Interference may be corrected by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Plug the equipment into an outlet on a circuit different from that to which the receiver is
connected.
CAUTION!
The Federal Communications Commission warns the user that changes or modifications to the unit not
expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
3
Contents
Precautions......................................................................................................................................4
Attaching / Detaching the Base to the Monitor ............................................................................5
Package Contents ...........................................................................................................................6
Hardware Setup ............................................................................................................................... 6
Hardware Installation ......................................................................................................................7
Menu Control Buttons..................................................................................................................... 8
On Screen Display (OSD) Menu Mode......................................................................................9-10
Display Modes ............................................................................................................................... 11
Specifications ................................................................................................................................12
Troubleshooting your DVI monitor connection ..........................................................................13
Troubleshooting ............................................................................................................................14
Maintenance / Cleaning Your Monitor .........................................................................................15
Service Procedure.........................................................................................................................16
Warranty.........................................................................................................................................17
4
Precautions
1. Read all of these instructions and save this manual for later use.
2. Follow all warnings and instructions on the product.
3. Do not cover or block the ventilation holes in the case.
4. Do not insert sharp objects or spill liquid into the LCD monitor through the cabinet slots; this
may cause accidental fire, electric shock or failure.
5. Unplug the unit when not in use for an extended period of time.
6. Do not attempt to service this product yourself, as opening or removing the cover may expose
you to potential electric shock. Only a qualified technician should service this product.
7. Do not touch the screen directly with your fingers as it may damage the screen; the oil from
your skin is difficult to remove.
8. Do not apply pressure to the screen, the LCD is very delicate.
9. Keep the monitor away from extreme heat, cold or humid places.
10.Do not place directly under sunlight, dusty surroundings or near equipment which may
generate strong magnetic fields.
5
Attaching the Base to the Monitor
STEP 1 STEP 2
Detaching the Base off the Monitor
STEP 1 STEP 2
Press the two tabs toward the inside of the base. While holding the two tabs in, pull
the base away from the pedestal.
6
Package Contents
19” TFT LCD Monitor
External Univ15 pin D-sub
(RGB Analog)
input signal cable
Audio connector cable
Power cord
User’s Manual
Hardware Setup
Handle the LCD monitor with care. Turn off the monitor’s and computer’s power before beginning setup. Follow the
installation instructions step by step.
Input
NO.
Terminal Function
AC-In AC power input 100~240V,
50/60HZ
VGA connector
To PC VGA connector
DVI connector
To PC DVI connector
Audio-In Audio input
7
Hardware Installation
Please note for Windows
®
User’s
Before attaching your new LCD monitor to your computer, please make sure that your resolution and refresh rates are set
correctly for your monitor to work properly. This is especially important if you are changing monitors (for example, from a
CRT to a LCD). Before disconnecting your old monitor, please set the resolution to 1440 x 900 and set the refresh rate to
60Hz. You can adjust these settings by right clicking your desktop, select “Properties”, then “Settings”. To adjust the
refresh rate, click on “Advanced” and search for this option.
Video card settings will be different based on the video capability of your computer. Please consult your video graphics card
or computer manual for more information.
1.
Carefully position your LCD monitor so that you can see all of the connection ports on the bottom of the monitor.
2.
A.) Plug one end of the 15-pin D-Sub signal cable into the VGA connector
on the monitor and plug the other end of
the cable into the 15-pin D-Sub connector at the rear of your PC.
B.) OR if you are using a DVI signal cable (not included) plug one end into the DVI connector
on the monitor and plug
the other end of the cable into the 24-pin DVI connector
at the rear of your PC. Make sure that all of the screws are
hand-tightened securely.
3.
Plug the Audio connector to the Audio In port
on the monitor, and to the computer line out at the rear of your PC. This
is optional if you wish to use a different audio source.
4.
Plug the power connector to the AC In port
port at the rear of the monitor.
5.
Connect the power cord to the power source.
6.
Power on the computer and the monitor.
7.
For best quality performance, set the resolution as shown on the Display Mode chart.(see pg. 11).
8
Menu Control Buttons
No.
Symbol
Function
1.
Auto Adjust (note: this feature will function when
VGA connector is in use.)
2. To navigate up through the option selection.
1. Show the main OSD menu.
2. To navigate down through the option selection.
1. Turns the power on / off.
2. Blue LED indicates power is on.
1. Decrease an option value.
2. To enter a submenu
1. Increase an option value.
2. To enter a submenu
•Press the
button to auto adjust horizontal and vertical position to default settings.
•Press the
button to display the OSD menu (in OSD mode, this button will also navigate to the submenus).
•Select the desired option menu by pressing the
or
button.
•Push the
or
button to decrease or increase the value of the current OSD selection.
•The OSD menu will close automatically after 20 seconds of inactivity.
9
On Screen Display (OSD) Menu Mode
OSD Sub-menu
DISCONNECTOR
If this warning appears,
1. Check the signal connection between the computer and LCD monitor.
2. Check the connector. If it is bent or damaged, the signal cable may be affected.
3. If the monitor is in “sleep” mode to save power, please move the mouse or press any key to “wake” it and return to
working mode.
4. Please check input diagrams, and make sure the monitor has been properly configured.
OUT OF RANGE
This warning indicates that the input signal frequency does not match those supported by this monitor. For this model,
horizontal frequency must be in the range of 30 ~ 80 KHz and vertical frequency in the range of 60~75 Hz. Please make sure
your input signal is within these ranges.
Option Icons
Option
Current mode Frequency
Current mode resolution
10
OSD (On-Screen Display) Menu Mode
1. Press the
button to access the OSD menu.
2. Select the desired option, by pressing the
or
button.
3. Press the
or
button to enter sub menus.
4. Use the
or
buttons to adjust the selected option value(s).
5. Note -
Please adjust your Speaker Volume via your PC computer Speaker Volume control icon.
Please note that Sound will continue to play when your monitor is off. To turn off the sound please switch off your PC
computer or mute the Speaker Volume control icon.
MISCELLANEOUS
RETURN
‘‘Yes’’ will take you to the main menu. ‘‘No’’ will bring you to the
Miscellaneous sub-menus.
OSD H-POSITION
Adjust
s
the horizontal position of the OSD
menu
.
OSD V-POSITION
Adjust
s
the vertica
l position of the OSD
menu
.
OSD DURATION
Adjust
s
the tim
e that the
OSD menu
remains on the screen
.
AUTO COLOR
Adjust
s
the color
to the optimal settings for your computer
automatically.
SOURCE
Selects the Video source as either
VGA or DVI.
CONTRAST Adjusts the difference between light and dark areas.
PHASE Adjusts the phase of PLL clock.
CLOCK Adjusts the frequency of the PLL clock.
H-POSITION Adjusts the horizontal position of the display.
V-POSITION Adjusts the vertical position of display.
RESET Returns to the factory default setting.
COLOR TEMPERATURE
Adjusts the color temperature.
RED Adjusts the Red color temperature.
GREEN Adjusts the Green color temperature.
BLUE Adjusts the Blue color temperature.
LANGUAGE Selects the display language of the OSD Menu.
MISCELLANEOUS
‘‘No’’ will take you to the exit menu. ‘‘Yes’’ will bring you to the sub menus
of the Miscellaneous menu.
EXIT OSD Exit and save the settings.
BRIGHTNESS
Adjusts the brightness of the display manually.
Table of contents
Languages:
