Vixen R200SS Manual
How to collimate the R200SS
First loosen all the three collimation “push” screws and tighten the other three
collimation “pull” screws on the primary mirror cell completely to “reset” the primary
mirror to a position where the primary mirror is placed closely to the mirror cell.
1. Remove the blue cap on the center of the four-vane spider to access adjustment
screws for collimation. Loosen the fixing screw on the dead center of the spider to
remove the secondary mirror holder with the mirror. There might be some
washers on the center fixing bolt with which the secondary mirror holder is
attached and please take care not to drop them onto the primary mirror.
2. Put a tiny dot at the center of the optical axis of the secondary mirror (offset 3.8mm
from the center of the elliptical secondary mirror, refer to the Figure 2) by using a
template below. A size of the dot should be about 1mmm to 2mm in diameter.
3. Return the secondary mirror holder with the mirror to the original place, and
tentatively fix it with the fixing bolt lightly. At this stage do not touch the other
three adjustments screws on the secondary mirror holder.
4. Draw a circle with diameter of 55mm on a black paper to make a disc. Open a pin
hole of about 1mm to 2mm at the center of the disc. Cut out of the disc and place
it into the change-over ring shown in the Figure 1.
5. Using a Sight tube or Cheshire eyepiece and attach it to the visual back of the
focuser to look at the secondary mirror surface through the pin hole. You can see
the dot on the secondary mirror shown in the Figure 3. Check if the dot moves up
and down in the field of view of the pin hole when you move the secondary mirror
holder to the left and right-hand direction a little. When it occurs, the dot may
not be written in the center of the optical axis correctly. Return to the procedure 2.
6. Assuming that cross hairs are put in the field of view shown in the Figure 3, check
which side on the vertical Y axis of the imaginary cross hairs the dot can be seen.
If the dot is just on the line of Y axis, you can proceed to next step. If the dot is
seen on the left-hand side, it means that the secondary mirror is somewhat distant
from the primary mirror. If the dot is seen on the right-hand side, it means that
the secondary mirror is somewhat close to the primary mirror. Please make sure
that you return all the washers to the same place as they are.
7. Next, check which side on the horizontal X axis of the imaginary cross hairs the dot
can be seen. If the dot is just on the line of X axis, you can proceed to next step. If
the dot is seen above of the line, it means that the secondary mirror comes near the
upper side shown in the Figure 5. In this case loosen the collimation screw “C”
and tighten the screw “B” on the spider shown in the Figure 4. If the dot is seen
below of the line, loosen the collimation screw “B” and tighten the screw “C”
oppositely.
8. Confirm that the dot is seen at the center of the imaginary cross hairs in the field of
view. Remove the disc from the change-over ring.
9. Rotate the secondary mirror holder so that each of distances “a” and “b” becomes
equal shown in the Figure 6. Now fix the secondary mirror holder tightly.
10.Again you need to adjust the position of the secondary mirror precisely with the
collimation screws “B”, “C” and “A”. When you shift the secondary mirror upper or
lower, turn the screws “B” or “C” only and don’t use the screw “A”. When you shift
the secondary mirror forward, turn the screw “A”. Turning the screws “A” and “B”
evenly shifts the secondary mirror backward.
11.Aligning the primary mirror: When looking into the drawtube without attaching
an eyepiece, you can see like the diagram blow if the optical axis is correct. If you
cannot see like the diagram, align the primary mirror with the collimation “push
and pull” screws on the primary mirror cell.
12.Finally a star test. Take the telescope outside and let the optics fully cool to the
ambient temperature.
Table of contents
Other Vixen Telescope manuals
Vixen
Vixen SX(SPHINX) User manual
Vixen
Vixen VC200L User manual
Vixen
Vixen GP2 PHOTO GUIDER S User manual
Vixen
Vixen VC200L Manual
Vixen
Vixen Porta ED80Sf User manual
Vixen
Vixen BT81S-A User manual
Vixen
Vixen SD Series User manual
Vixen
Vixen Porta A70Lf User manual
Vixen
Vixen BT81S-A User manual
Vixen
Vixen Sphinx User manual
Vixen
Vixen R150S User manual
Vixen
Vixen VC200L User manual
Vixen
Vixen Starbook-S Instruction Manual
Vixen
Vixen AX103S User manual
Vixen
Vixen BT81S-A User manual
Vixen
Vixen Refractors A81M User manual
Vixen
Vixen VMC260L User manual
Vixen
Vixen R200SS Newtonian Reflector User manual
Vixen
Vixen GREAT POLARIS User manual
Vixen
Vixen SX Polar Axis User manual
