Vivo STAND-V103C User manual

Flush to Wall Triple Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v103c

SKU: STAND-V103C

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

A (x1)

Pole

B(x1)

Clamp

C(x3)

VESA Plate

J (x1)

So Pad

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualied technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

D(x2)

Arm

E(x2)

Arm Extension

F (x2)

Side VESA

Bracket

G(x1)

Center VESA

Bracket

H (x1)

Bracket Plate

I (x1)

Arm Support

Bracket

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

L (x1)

Pole Cable Clip

M (x4)

Arm Cable Clip

N (x1)

Pole Cap

S-A (x3)

M6x10mm

Thumbscrew

S-B (x2)

M4x5mm

Screw

S-C (x1)

M8x50mm

Screw

S-D (x2)

M8 Washer

S-E (x1)

M8 Nut

K (x1)

Grommet Plate

S-F (x4)

M6x27mm

Screw

S-G (x3)

M6x16mm

Flathead Screw

S-H (x1)

M5x16mm

Flathead Screw

M-A (x12)

M4x12mm

Screw

M-B (x12)

M4x16mm

Screw

M-D (x12)

M5x16mm Screw

M-E (x12)

M5 Washer

M-F (x12)

Spacer

T-A (x1)

4mm Allen

Wrench

T-B (x1)

6mm Allen

Wrench

T-C (x1)

Wrench

M-C (x12)

M5x12mm

Screw

S-I (x2)

M8x42mm

Screw

ASSEMBLY STEPS

OPTION A: Clamp Installation

Attach Upper Clamp (B1) to Pole (A) using the

M6x16mm Flathead Screws (S-G) and 4mm Allen

Wrench (T-A). Peel the protective lm o of So

Pad (J) and place it onto Upper Clamp (B1).

Separate Clamp (B) into Upper Clamp (B1) and Lower Clamp (B2) using 4mm Allen Wrench (T-A).

OPTION B: Grommet Base Installation

Remove the screw from the top of Lower Clamp

(B2) using a Phillips screwdriver, and set aside

Clamp Bolt (B3) and Support Plate (B4). Cut

So Pad (J) along the perforated lines. Peel the

protective lm o of So Pad (J) and place the

pieces onto Grommet Plate (K) as shown below.

TOOLS NEEDED

15.4lbs

Per Monitor

(7kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

Phillips

Screwdriver

STEP 2

STEP 1

T-A

B1 S-G

B2 B3

STEP 2 (Continued)

OPTION A: Clamp Installation

For thinner desktops (10-50mm), re-attach

Lower Clamp (B2) to Upper Clamp (B1)and

tighten the screws using the 4mm Allen Wrench

OPTION B: Grommet Installation

If not using an existing through-hole, using a

10mm (⅜”) drill bit, drill through the desktop at

least 2” away from the edge. Attach Pole (A) and

Grommet Plate (K) to the desktop using Support

Plate (B4) and Clamp Bolt (B3) as shown below.

T-A

For thicker desktops (40-85mm), disassemble

Lower Clamp (B2) using a Phillips screwdriver

as shown below. Flip the L-bracket over and

reassemble. Then re-attach Lower Clamp (B2) to

Upper Clamp (B1) and tighten the screws using

4mm Allen Wrench (T-A). Tighten the clamp

assembly to the desktop.

T-A

STEP 4

Slide Side VESA Brackets (F) onto Arm Extensions (E). Tighten the screw on the back of Side VESA

Brackets (F) using 4mm Allen Wrench (T-A) to secure them in place. Install M4x5mm Screws (S-B) into

Arm Extensions (E) using a Phillips screwdriver.

STEP 5

Install the arm assembly onto Pole (A) and

tighten the screw on the back of Arm Support

Bracket (I) using 4mm Allen Wrench (T-A) to

secure it in place. Attach Pole Cap (N) to the

top of Pole (A).

Assemble Arms (D), Arm Support

Bracket (I) and Bracket Plate (H)

using M6x27mm Screws (S-F) and

4mm Allen Wrench (T-A). Secure

Arm Extensions (E) to Arms (D)

using M8x42mm Screws (S-I)

and 6mm Allen Wrench (T-B).

Mount Center VESA Bracket (G) to

Bracket Plate (H) using M8x50mm

Screw (S-C), M8 Washers (S-D),

and M8 Nut (S-E) with 6mm Allen

Wrench (T-B) and Wrench (T-C).

STEP 3

S-F T-A

S-I

T-B

S-C

S-D

S-E

T-C

T-A

S-B

T-A

STEP 6

Assemble Arm Cable Clips (M) to Arms (D) and Arm Extensions (E). Attach Pole Cable Clip (L) to Pole (A).

STEP 7

Attach VESA Plates (C) to the back of the monitor using Screws (M-A through M-D) and Washers (M-E).

If needed, use Spacers (M-F).

STEP 8

Slide monitors with VESA Plates (C) onto Side VESA Brackets (F) and Center VESA Bracket (G). Use

M6x10mm Thumbscrews (S-A) to secure them in place.

S-A

STEP 9

Manage cables using Arm Cable Clips (M) and Pole Cable Clip (L).

STEP 10

Adjust tilt, height, and horizontal orientation using Allen Wrenches (T-A and T-B) as shown below.

Store Allen Wrenches (T-A and T-B) in Pole Cable Clip (L).

T-B

T-A

LAST UPDATED: 01/31/2022

REV1

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 