Vista 2117 User manual

INSTALLATION INSTRUCTIONS Specialty Lights

2117

Factory sealed

liquid-tight

connector

Cement counterweight

base with adjustable

mounting bracket

Lens

Conduit

sweep

Housing

18-3 Double-jacketed

water resistant cable

Stainless steel

screw

TOOLS REQUIRED FOR

INSTALLATION:

●Blade head screwdriver

●Wire strippers

FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT EXCEED 25 AMPS, 15 VOLT MAXIMUM.

WARNING: Luminaires must be installed in accordance with the National Electrical Code (NEC) and local codes.

Failure to do so will void the warranty and may result in serious injury and/or damage to the luminaire.

SAFETY WARNING: Luminaire can become very hot depending on lamp wattage used. Lens and metal around

lamp can become hot enough to blister hands. Particular care should be taken not to locate luminaires where

small children can reach them if high wattage lamps are used.

LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A POOL OR SPA. SECONDARY CABLE IS NOT TO

BE BURIED MORE THAN 6”. WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT TO EXCEED THE TOTAL WATTS OF

TRANSFORMER RATING. DO NOT USE EXTENSION CORDS ON POWER UNITS.

NOTE: Always use UL recognized wire connectors for connections.

NOTE: Save these instructions for future reference.

CAUTION: THIS LUMINAIRE IS INTENDED FOR USE IN WATER GARDENS AND PONDS ONLY. NOT FOR USE IN SWIMMING POOL OR

SPA APPLICATIONS.

1. To prevent electrical shock, disconnect transformer from electrical supply before installation or service.

NOTE: DO NOT pull the underwater cable. If wire is pulled, it may break the liquid tight seal and void the warranty.

NOTE: DO NOT loosen or remove the liquid tight connector. This will damage the factory set seal and result in possible

leakage.

NOTE: The end of the underwater cable must be potted to prevent moisture from entering the cable and consequently

entering the luminaire. Connection or splicing of cable must be made above the water line and at least 4 feet from the

water edge. This luminaire comes equipped with 15 feet of waterproof cable to facilitate installation away from the

water.

NOTE: Each luminaire is factory tested prior to shipment. Traces of water may be visible as a direct result of factory

underwater testing.

2. Strip the two (2) leads from the luminaire. Using the two (2) silicone lled connectors (provided), connect the leads from

the luminaire to the main supply cable leads.

3. To adjust luminaire aiming angle, loosen the wing nut in bracket holding the luminaire. Hold luminaire at selected

angle and tighten the wing nut rmly.

4. Supply power to luminaire and check for proper operation.

12V COPPER SERIES

1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)

FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com

IMPORTANT SAFETY INSTRUCTIONS

THE LIGHTED LAMP IS HOT!!

WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO

PERSONS:

1. Turn off/unplug and allow to cool before replacing lamp.

2. Lamps get hot quickly! Contact only switch/plug when turning on.

3. Do not touch hot lens, guard or enclosure.

4. Keep lamp away from material that may burn.

5. Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may

damage lamp.

6. Do not operate luminaire tting with a missing or damaged cover.

CAUTION: LUMINAIRE IS RATED AT 12 VOLT AC. DO NOT CONNECT

LUMINAIRE TO ANY OTHER VOLTAGE.

LAMP INSTALLATION/REPLACEMENT:

CAUTION: Do not exceed maximum wattage marked on luminaire label.

1. To prevent electrical shock, disconnect transformer from electrical supply before service.

2. Remove the ve (5) screws from lens cover.

3. Remove lens to expose lamp.

4. Replace lamp with correct wattage and type marked on xture label.

5. Re-install lens, gasket, and cover then tighten the ve (5) screws evenly and securely.

1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)

FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com

Table of contents

Popular Outdoor Light manuals by other brands

Sealey

Sealey LED37 instructions

nordlux

nordlux VEJERS Mounting instruction

SImx

SImx ELITE LED LHTC637 installation instructions

GEV

GEV CAROLINE 10833 manual

NEBO

NEBO NEB-LSP-0020 Use and care guide

WE-EF

WE-EF PFL540 LED Installation and maintenance instructions

Lindby

Lindby 9949029 Intended use

HEPER

HEPER DOGO Side LW6048.585-US Installation & maintenance instructions

HEPER

HEPER LW8034.003-US Installation & maintenance instructions

Maretti

Maretti VIBE S 14.6080.04.A quick start guide

BEGA

BEGA 84 253 Installation and technical information

HEPER

HEPER MINIMO Installation & maintenance instructions

LIGMAN

LIGMAN BAMBOO 3 installation manual

Maretti

Maretti TUBE CUBE WALL 14.4998.04 quick start guide

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB installation instructions

urban ambiance

urban ambiance UQL1273 installation instructions

TotalPond

TotalPond 52238 instruction manual

Donner & Blitzen

Donner & Blitzen 0-02661479-2 owner's manual