Vista QSW16M User manual

QSW16M User manual V1.0

QSW16M

16 Chn PoE managed switch

QSW16M User manual V1.0

Before You Begin

Read these instructions before installing or operating this product.

Note: This installation should be made by a qualified service person and should conform to local codes.

This manual provides installation and operation information. To use this document, you must have the following minimum

qualifications:

• A basic knowledge of CCTV systems and components

• A basic knowledge of electrical wiring and low-voltage electrical connections

Intended use

Only use this product for its designated purpose; refer to the product specification and user documentation.

Customer Support

For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and any other

documentation provided. If you still have questions, please contact Norbain Technical Support and Sales:

Norbain SD, 210 Wharfedale Road, IQ Winnersh, Wokingham, Berkshire RG41 5TP, England.

UK +44 (0) 118 912 5000

Note: You should be at the equipment and ready with details before calling Technical Support.

Conventions Used in this Manual

Boldface or button icons highlight command entries. The following WARNING, CAUTION and Note statements identify

potential hazards that can occur if the equipment is not handled properly:

* WARNING:

Improper use of this equipment can cause severe bodily injury or equipment damage.

* CAUTION:

Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

This apparatus is manufactured to comply with the radio interference.

A Declaration of Conformity in accordance with the following EU standards has been made. The

manufacturer declares that the product supplied with this document is compliant the provisions of the EMC

Directive 2004/108/EC, the CE Marking Directive 93/68 EEC and all associated amendments.

All lead-free products offered by the company comply with the requirements of the European law on the

Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means our manufacture

processes and products, are strictly “lead-free” and without the hazardous substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be

collected separately at the product end-of-life. This applies to your product and any peripherals marked

with this symbol. Do not dispose of these products as unsorted municipal waste.

* This symbol indicates electrical warnings and cautions.

** This symbol indicates general warnings and cautions.

NORBAIN SD reserves the right to make changes to the product and specification of the product from time to time without

prior notice.

QSW16M User manual V1.0

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

WARNINGS AND CAUTIONS:

To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other openings

on the equipment.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from

the apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

13. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE

RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING

INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

14. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

15. ITE is to be connected only to PoE networks without routing to the outside plant.

CE COMPLIANCE STATEMENT

WARNING

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

QSW16M User manual V1.0

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Contents

1.Introduction................................................................................................................................................5

1.1 Overview.............................................................................................................................................5

1.2 Product Features.................................................................................................................................5

1.3 Front panel..........................................................................................................................................5

2 Installation.................................................................................................................................................6

2.1 Contents .............................................................................................................................................6

2.2 Installation requirements.....................................................................................................................6

2.3 Rack mount.........................................................................................................................................6

2.4 Desk mount........................................................................................................................................7

2.5 Wall mounting.....................................................................................................................................7

2.6 Cable connections...............................................................................................................................8

2.6.1 Configuration cable.......................................................................................................................8

2.6.2 Power connection.........................................................................................................................8

3. PoE Web Page management ...................................................................................................................9

3.1 Connection to web page......................................................................................................................9

3.2 Switch IP address change.................................................................................................................10

3.2 Password change..............................................................................................................................10

3.3 Factory defaults ................................................................................................................................10

3.4 Restore IP address and Password....................................................................................................10

3.5 Device information ............................................................................................................................11

4. PoE Power management........................................................................................................................12

4.1 PoE settings......................................................................................................................................12

4.2 Power Status.....................................................................................................................................12

4.3 Port Status and Control.....................................................................................................................12

5. CCTV Mode............................................................................................................................................13

QSW16M User manual V1.0

1.Introduction

1.1 Overview

This manual covers the installation set up and use of the QSW16M 16 Chn PoE Switch

1.2 Product Features

16 100Mbps downlink PoE Ethernet ports, 2 x gigabit uplink ports and 1 gigabit fibre port

PoE ports support PoE+ ( Max 30W per channel , total budget 250W)

CCTV Mode –Allows extended PoE and Data ( up to 250M of cat5e cable)

LED indication of Power consumption

Standards: IEEE802. 3、IEEE802. 3u、IEEE802. 3ab、IEEE802. 3af/at

4K MAC address, 2.75Mb cache

Quick installation, easy operation, wall mount, desk or racks mount.

1.3 Front panel

QSW16M User manual V1.0

2 Installation

2.1 Contents

Please ensure that all items are present when un-packing the switch

2.2 Installation requirements

The switch should only be installed in an indoor environment , either in a rack mount cabinet, secured to a

wall or desk mounted. The following requirements should be observed:

Leave a minimum of a 10cm air gap to allow sufficient ventilation

The wall or cabinet should be of sufficient strength to support the switch

The Cabinet should be well grounded

2.3 Rack mount

Installation process:

1. Check rack grounding and stability

2. Use the provided screws to fit the connection ears to the switch

3. Use the provided screws to fit the switch in the rack

QSW16M User manual V1.0

2.4 Desk mount

The Switch can simply be mounted on a desk or table top, please ensure the environment is stable and

clean.

If required the rack mount ears can be used to secure the switch to the desk top.

2.5 Wall mounting

The switch can be hung on a wall, please ensure the wall is of sufficient strength to support the switches

weight, and that the correct fixings are used for the wall construction.

Procedure:

1. Use the provided screws to fit the connection ears to the switch

2. Use the correct fixings for the wall construction to mount the switch to the wall

QSW16M User manual V1.0

2.6 Cable connections

2.6.1 Configuration cable

To configure the PoE settings etc connect a network cable to “PoE managed” port on the front of the

switch.

2.6.2 Power connection

The switch requires 230VAC mains connection. Ensure the power supply conforms to this.

The AC power connection LED will show when power is applied.

QSW16M User manual V1.0

3. PoE Web Page management

The QSW16M Web management function allows the operator to control and manage the PoE output of

each of the 16 ports.

3.1 Connection to web page

1. Using a Network cable ( Crossover for direct connection)

2. As default the Switches IP address is 192.168.1.200 (Subnet 255.255.255.0).

3. Ensure that your PC is set to an IP address within the same range as the switch.

4. Open a web browser on your PC ( IE7 or later, Firefox or Chrome

5. Enter the switches IP address within the browser ( 192.168.1.200)

6. The following login page will appear:

7. Default login details are: User –admin, Password –admin.

8. Next click on “Login”, to display the following page:

QSW16M User manual V1.0

3.2 Switch IP address change

1. To Change the IP Address of the switch to a logical address for your network, click on “IP” in the

top menu bar, the following menu will be displayed:

2. Change the IP address , Subnet and Gateway to suit the individual network, These address details

should be supplied by the Network manager.

3.2 Password change

For additional security it is advised that the default password is changed. To do this click on “Password” on

the top menu bar, to show the following menu:

Enter the current password, to confirm you are an authorised user, then enter the new password twice.

Finally click “OK”.

3.3 Factory defaults

If it is necessary to default the switch to it’s original settings, click on “Factory Default” in the top menu bar

to display the following menu:

Click on “OK”, wait for 10 seconds. The switch will then be defaulted.

3.4 Restore IP address and Password

If it is necessary to restore the IP address and Password, this can be done using the following procedure:

1. Power up the switch

2. Remove the RJ45 cable form the “PoE Managed” port,

3. Using an appropriate tool, press and hold the “init” button for 5 seconds.

Other manuals for QSW16M

Table of contents

Other Vista Network Router manuals

Vista

Vista QSW8 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview