Vision Drive Black Box VD-9000FHD User manual
2012.09.01 12:00:00
CAR BLACK BOX
®
Ver. VD-9000FHD 1.0 E
User Manual
2
3
5
6
7
8
9
10
15
19
30
........................
...........................
......................
.......................
.............
...........
.............
............
......................
.........
..........................
Before Use
Caution
Components
Part Names
Product Specification
Installation Precautions
Installation Sequence
Installation Procedure
Product Use
PC Analysis Program Use
Warranty
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
INDEX
Thank you for choosing VisionDrive®.
This section describes product cautions and the scope of the warranty service covered by us
Please use the product with complete understanding below.
We shall not be held responsible for damage caused by errors or data loss of this product,
as well as any damage or loss derived from the device not operating normally.
The product is designed to record, store, play and analyze videos caused by impacts and
vehicle accidents or as recorded by user’s discretion. However, it is not assured that the
product will record video in every instance.
Furthermore, under circumstances where the impact is too weak, the vibration sensor may
not be able to detect the impact, which induces that the system will be unable to
automatically start recording the [Event] file. In such a situation, the urgent save button
(SHOT) on the product should be pressed to start recording a video to the [Event] folder.
The information in this manual may change without prior notice due to technical changes or
upgrades. Check for updates periodically to ensure full knowledge of both the warranty service
and responsibility scope.
www.visiondrive.co.kr
2
Before Use
Warranty Service and Responsibility
visiondrive.co.kr
The SD card is the only usable SD card for this product. In case of a lost SD card,
please contact your local retail shop to purchase a replacement.
If a damaged or a non-authentic SD card is used, the recorded data may be
damaged or will not record and/or replay due to difference in quality.
Do not disassemble or remodel this product as it can cause an electric shock.
Any malfunctioning after such action will result in the product being unfit for use
and void all warranty/service provisions. Consult the retailer for product mainte-
nance and repairs if necessary.
Only use adaptors with the appropriate specifications. The use of other adaptors
will defect the product and or cause fire.
All wiring should be carefully implemented so the cables do not get damaged.
Where the product is wired to the power supply of the vehicle directly or if the
cigar jack is connected to the power supply while the engine is off, make sure to
disconnect the device to prevent battery drain on your vehicle.
When installing the device to your vehicle, follow all the procedures and make
sure the mount is secure. Unclean surfaces will weaken the adhesive strength and
can damage the product if it drops due to poor adhesion.
This product is not waterproof. Do not allow liquids and impurities into the
product.
Do not use chemicals or detergents to clean the device. This can result in
malfunctioning of the product.
Accumulation of impurities on the camera lens or the window surface near the
camera may result in video distortion and reduced clarity of recorded data.
Surrounding of the product should always be kept clean.
Excessive tinting on the window may also distort or reduce clarity of recorded
data.
Excessive tinting on the window may also distort or reduce clarity of recorded
data.
Recording can be distorted under the condition where brightness suddenly
changes like passing through a tunnel, direct sunlight reflection during day time or
where only low light is available at night time.
3
Caution
visiondrive.co.kr
If not enough light is available, using additional external lighting may help record
better images.
In case of slight impact, the product may not be able to create an event file automati-
cally (it is however recorded as a Normal file). In such a case, please use the (SHOT)
button to create an event file manually.
If you eject the SD card while the product is operating, the recorded data may be
damaged.
Ensure the main power is completely off and the device is fully powered off (no
indicator lights are on) before removing the SD card from the product.
Interacting with the product while driving is risky and may cause an accident. This
should only be performed when the vehicle is stationary and parked in a safe place.
Do not keep the product in extreme temperatures or in humid areas. Being under
extreme heat in summer days or freezing cold in winter days may result in defection
of the product. Also, do not expose the product to direct fire or water.
Do not disassemble the product as this may result in defect of the product which is
not covered by us.
Keep the SD card in its case when not in use for the product.. Static electricity or
other environmental elements can damage the recorded data.
SD cards are an expendable supply. After normal periods of use, partial memory
sectors may be damaged and will disable the recording of data.
The system installed on the SD card provides an automated checking function. If the
use of the automatic checking function identifies problems with the SD card, then we
recommend purchasing a new one for recording data.
If the SD card is ejected or the system is turned off while recording, copying or
deleting data, the stored data may be damaged or lost and/or the SD card may
become defective.
Manufacturer is not responsible for loss or destruction of stored data caused by
actions above.
Copy and keep important data on other data storages such as hard disk, CD or
portable flash memory.
4
Caution
visiondrive.co.kr
2012.09.01 12:00:00
5
!! Manual or Quick guide can be provided in computer file.
Components are subject to change without prior notice.
Components
visiondrive.co.kr
Wire Holders Cigarette lighter
Power Adaptor
Main Unit
Attachment Bracket
(Glass Plate Mount)
SD card
Part Names
REC LED
LCD SCREEN
GPS SENSOR
CAMERA
BRACKET INSTALLED
ON MAIN UNIT
POWER PORT
TECH SUPPORT PORT
GPS LED
MIC
VIEW BUTTON
PLAY BUTTON
SHOT BUTTON
SD CARD SLOT
Model
Camera
Resolution
Recording
Lighting Environment
Camera Rotation
Display
GPS
G- Sensor
Storage
Audio Recording
Voice Announcement
Event Recording
Power Supply
Internal Battery
Operation Temperature
Car Battery Monitoring
Dimensions
PC OS
File Protection
Analyzer Program
Additional Details
24Hr Loop Recording / Manual & Emergency Recording Support
Min. 0.1 Lux
Vertical 65°
Camera Angle Diagonal 120°
2.4" TFT Color LCD
Built-in GPS Module (Sirf IV)
Built- in 3- Axis Sensor (x- y- z)
SD memory card (SDHC compatible 1G ~ 64G)
Built- in MIC (One-touch recording)
Built- in Speaker
10 sec. before impact ~ 15/30/45/60 sec. after impact
DC 12V ~ 24V Cigarette Power Supply
EDLC for Emergency Backup
-20 °C ~ 80 °C
Low Voltage Detection / Control
111mm * 75mm * 27mm
Windows XP/ VISTA / Windows 7
Password Access
Dedicated Analyzer (AVI file transformation support)
Automatic Parking Mode Function
Motion Detection
Date/Time Display
Video Quality Enhancement
7
Product Specification
visiondrive.co.kr
VISIONDRIVE VD- 9000FHD
1 Camera
Full HD Color CMOS digital camera
1920 x 1080 (Full HD) Max. 30 fps
It is recommended using only authorized SD cards with the VisionDrive® products.
Install the product after parking your vehicle in a bright and safe area.
Install the system when ignition is off. Especially, after the power source has been turned off
completely.
Use the power cable provided with the product for the cigarette lighter power connection in the
range of DC12V to DC24V. If power wiring is involved, we recommend a professional service for
the installation.
Prior to the installation, clean the area of the installation where the camera will be positioned.
DO NOT eject the SD card while the product is in operation.
DO NOT disconnect the product before its complete off.
Do NOT attempt to modify, separate or repair the product yourself in any way.
For safe installation and operation, carefully read all the information stated
below.
DO NOT disconnect the power supply while the system is booting up.
Be aware of that engine ignition may disconnect the product for short periods of
time.
8
Installation Precautions
visiondrive.co.kr
Assemble the bracket with the main unit
Insert SD card into the unit
Connect cable and attach on windshield
Connect to power source to turn on the unit
Adjust the camera angle
Check LED lamps
Arrange and secure wires using wire holders
1.
2.
3.
4.
5.
6.
7.
Installation Sequence
9
visiondrive.co.kr
Table of contents
Other Vision Drive Dashcam manuals
Vision Drive
Vision Drive VD-1500MG/1500MB User manual
Vision Drive
Vision Drive VD-3000 User manual
Vision Drive
Vision Drive VD-8500WHG User manual
Vision Drive
Vision Drive VD-7000W User manual
Vision Drive
Vision Drive VD-7000W Quick start guide
Vision Drive
Vision Drive VD-3000 User manual
Vision Drive
Vision Drive VD-9500H User manual
Vision Drive
Vision Drive VD-3000 User manual
Vision Drive
Vision Drive VD-9000FHD User manual
Vision Drive
Vision Drive VD-3000 User manual
