Vishay TSOP64 Series User manual

Document Number: 82177 www.vishay.com

Rev. 2.2, 23-Aug-10 1

IR Receiver Modules for Remote Control Systems

TSOP62.., TSOP64..

Vishay Semiconductors

MECHANICAL DATA

Pinning

1 = GND, 2 = N.C., 3 = VS, 4 = OUT

DESCRIPTION

The TSOP62.., TSOP64.. series are miniaturized SMD-IR

receiver modules for infrared remote control systems. PIN

diode and preamplifier are assembled on a lead frame, the

epoxy package is designed as IR filter.

The demodulated output signal can directly be decoded by

a microprocessor. The TSOP62.. is compatible with all

common IR remote control data formats. The TSOP64.. is

optimized to better suppress spurious pulses from energy

saving lamps but will also suppress some data signals.

This component has not been qualified according to

automotive specifications.

FEATURES

• Photo detector and preamplifier in one package

• Internal filter for PCM frequency

• Supply voltage: 2.7 V to 5.5 V

• Output active low

• Low power consumption

• High immunity against ambient light

• Low power consumption

• Compliant to RoHS directive 2002/95/EC and in

accordance to WEEE 2002/96/EC

SPECIAL FEATURES

• Improved immunity against ambient light

• Suitable burst length ≥10 cycles/burst

• Taping available for top view and side view assembly

BLOCK DIAGRAM APPLICATION CIRCUIT

16797

1234

PARTS TABLE

CARRIER FREQUENCY STANDARD APPLICATIONS (AGC2/AGC8) NOISY ENVIRONMENTS AND SHORT BURSTS (AGC4)

30 kHz TSOP6230 TSOP6430

33 kHz TSOP6233 TSOP6433

36 kHz TSOP6236 TSOP6436

36.7 kHz TSOP6237 TSOP6437

38 kHz TSOP6238 TSOP6438

40 kHz TSOP6240 TSOP6440

56 kHz TSOP6256 TSOP6456

33 kΩ

OUT

Demo -

GND

pass

AGCInput

Band

dulator

Control circuit

16839-1

IR receiver

GND

Circuit

µC

+ V

GND

Transmitter

with

TSALxxxx V

17170_7

OUT

The external components R

and C

are optional

to improve the robustness against electrical overstress

(typical values are R

= 100 Ω, C

= 0.1 µF).

The output voltage V

should not be pulled down to a level

below 1 V by the external circuit.

The capacitive load at the output should be less than 2 nF.

www.vishay.com Document Number: 82177

2Rev. 2.2, 23-Aug-10

TSOP62.., TSOP64..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.

TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient

ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)

PARAMETER TEST CONDITION SYMBOL VALUE UNIT

Supply voltage (pin 3) VS- 0.3 to + 6 V

Supply current (pin 3) IS5mA

Output voltage (pin 4) VO- 0.3 to 5.5 V

Voltage at output to supply VS- VO- 0.3 to (VS+ 0.3) V

Output current (pin 4) IO5mA

Junction temperature Tj100 °C

Storage temperature range Tstg - 40 to + 100 °C

Operating temperature range Tamb - 25 to + 85 °C

Power consumption Tamb ≤85 °C Ptot 10 mW

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT

Supply current (pin 3) Ev= 0, VS= 5 V ISD 0.65 0.85 1.05 mA

Ev= 40 klx, sunlight ISH 0.95 mA

Supply voltage VS2.7 5.5 V

Transmission distance

Ev= 0, test signal see fig. 1,

IR diode TSAL6200,

IF= 400 mA

d40m

Output voltage low (pin 4) IOSL = 0.5 mA, Ee= 0.7 mW/m2,

test signal see fig. 1 VOSL 100 mV

Minimum irradiance

Pulse width tolerance:

tpi - 5/fo< tpo < tpi + 6/fo,

test signal see fig. 1

Ee min. 0.3 0.45 mW/m2

Maximum irradiance tpi - 5/fo< tpo < tpi + 6/fo,

test signal see fig. 1 Ee max. 30 W/m2

Directivity Angle of half transmission

distance ϕ1/2 ± 50 deg

* t

10/f

is recommended for optimal function

16110

Optical Test Signal

(IR diode TSAL6200, I

= 0.4 A, 30 pulses, f = f

, t = 10 ms)

Output Signal

d1)

po 2)

7/f

<15/f

- 5/f

< t

+ 6/f

1.0

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

0.1 1 10 102103104105

- Irradiance (mW/m

)

- Output Pulse Width (ms)

21391

Input Burst Length

Output Pulse Width

λ= 950 nm,

Optical Test Signal, Fig.1

Document Number: 82177 www.vishay.com

Rev. 2.2, 23-Aug-10 3

TSOP62.., TSOP64..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

Fig. 3 - Output Function

Fig. 4 - Output Pulse Diagram

Fig. 5 - Frequency Dependence of Responsivity

Fig. 6 - Sensitivity in Bright Ambient

Fig. 7 - Sensitivity vs. Supply Voltage Disturbances

Fig. 8 - Sensitivity vs. Electric Field Disturbances

600 µs 600 µs

t = 60 ms

off

94 8134

Optical Test Signal

Output Signal, (see fig. 4)

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.1 1 10 102103104105

Ee- Irradiance (mW/m2)

Ton, Toff - Output Pulse Width (ms)

21392

λ= 950 nm,

Optical Test Signal, Fig. 3

Ton

Toff

0.0

0.2

0.4

0.6

0.8

1.0

1.2

0.7 0.9 1.1 1.3

f/f0- Relative Frequency16925

f = f0± 5 %

Δf(3 dB) = f0/10

E /E - Rel. Responsivity

e min. e

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

0.01 0.1 1 10 100

Ee- Ambient DC Irradiance (W/m2)

Ee min. - Threshold Irradiance (mW/m2)

Correlation with Ambient Light Sources:

10 W/m2= 1.4 kLx (Std. illum. A, T = 2855 K)

10 W/m2= 8.2 kLx (Daylight, T = 5900 K)

Wavelength of Ambient

Illumination: λ= 950 nm

21393

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1 10 100 1000

ΔVsRMS - AC Voltage on DC Supply Voltage (mV)

21394

Ee min. - Threshold Irradiance (mW/m2)

f = f0

f = 20 kHz

f = 30 kHz

f = 100 Hz

f = 10 kHz

100

150

200

250

300

350

400

450

500

0 500 1000 1500 2000 2500 3000

f - EMI Frequency (MHz)

E - Max. Field Strength (V/m)

20747

www.vishay.com Document Number: 82177

4Rev. 2.2, 23-Aug-10

TSOP62.., TSOP64..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length

Fig. 10 - Sensitivity vs. Ambient Temperature

Fig. 11 - Relative Spectral Sensitivity vs. Wavelength

Fig. 12 - Horizontal Directivity

Fig. 13 - Sensitivity vs. Supply Voltage

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0 20 40 60 80 100 120

Burst Length (number of cycles/burst)

Max. Envelope Duty Cycle

f = 38 kHz, Ee= 2 mW/m²

TSOP62..

TSOP64..

21396_6

Tamb - Ambient Temperature (°C)

Ee min. - Threshold Irradiance (mW/m2)

21397

0.15

0.2

0.25

0.3

0.35

0.4

0.45

- 30 - 10 10 30 50 70 90

0.0

0.2

0.4

0.6

0.8

1.0

1.2

750 850 950 1050 1150

λ- Wavelength (nm)16919

S ( ) - Relative Spectral Sensitivityλrel

16801

0.4 0.2 0 0.2 0.4 0.6

0.6

0.9

0°

30°

10° 20°

40°

50°

60°

70°

80°

1.0

0.8

0.7

rel

- Relative Transmission Distance

0.20

0.25

0.30

0.35

0.40

0.45

0.50

1.5 2.5 3.5 4.5 5.5234 5

VS- Supply Voltage (V)

Ee min. - Sensitivity (mW/m2)

21398

Document Number: 82177 www.vishay.com

Rev. 2.2, 23-Aug-10 5

TSOP62.., TSOP64..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

SUITABLE DATA FORMAT

The TSOP62.., TSOP64.. series are designed to suppress

spurious output pulses due to noise or disturbance signals.

Data and disturbance signals can be distinguished by the

devices according to carrier frequency, burst length and

envelope duty cycle. The data signal should be close to the

band-pass center frequency (e.g. 38 kHz) and fulfill the

conditions in the table below.

When a data signal is applied to the TSOP62.., TSOP64.. in

the presence of a disturbance signal, the sensitivity of the

receiver is reduced to insure that no spurious pulses are

present at the output. Some examples of disturbance

signals which are suppressed are:

• DC light (e.g. from tungsten bulb or sunlight)

• Continuous signals at any frequency

• Strongly or weakly modulated noise from fluorescent

lamps with electronic ballasts (see figure 14 or figure 15)

Fig. 14 - IR Signal from Fluorescent Lamp

with Low Modulation

Fig. 15 - IR Signal from Fluorescent Lamp

with High Modulation

Note

• For data formats with short bursts please see the datasheet of TSOP61.., TSOP63..

0101520

Time (ms)

16920

IR Signal

IR Signal from Fluorescent

Lamp with Low Modulation

0101520

Time (ms)

16921

IR Signal

IR Signal from Fluorescent

Lamp with High Modulation

TSOP62.. TSOP64..

Minimum burst length 10 cycles/burst 10 cycles/burst

After each burst of length

a minimum gap time is required of

10 to 70 cycles

≥12 cycles

10 to 35 cycles

≥12 cycles

For bursts greater than

a minimum gap time in the data stream is needed of

70 cycles

> 4 x burst length

35 cycles

> 10 x burst length

Maximum number of continuous short bursts/second 800 1300

Recommended for NEC code yes yes

Recommended for RC5/RC6 code yes yes

Recommended for Sony code yes no

Recommended for Thomson 56 kHz code yes yes

Recommended for Mitsubishi code (38 kHz, preburst 8 ms, 16 bit) yes yes

Recommended for Sharp code yes yes

Suppression of interference from fluorescent lamps Most common disturbance

signals are suppressed

Even extreme disturbance

signals are suppressed

www.vishay.com Document Number: 82177

6Rev. 2.2, 23-Aug-10

TSOP62.., TSOP64..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

PACKAGE DIMENSIONS in millimeters

ASSEMBLY INSTRUCTIONS

Reflow Soldering

• Reflow soldering must be done within 72 h while stored

under a max. temperature of 30 °C, 60 % RH after

opening the dry pack envelope

• Set the furnace temperatures for pre-heating and heating

in accordance with the reflow temperature profile as

shown in the diagram. Excercise extreme care to keep the

maximum temperature below 260 °C. The temperature

shown in the profile means the temperature at the device

surface. Since there is a temperature difference between

the component and the circuit board, it should be verified

that the temperature of the device is accurately being

measured

• Handling after reflow should be done only after the work

surface has been cooled off

Manual Soldering

• Use a soldering iron of 25 W or less. Adjust the

temperature of the soldering iron below 300 °C

• Finish soldering within 3 s

• Handle products only after the temperature has cooled off

2.35

R 1.7

5.51

0.5 ± 0.15

3 x 1.27 = 3.81

2.6

7.5

7.2

1.27

5.3

2.9

2.2

Pick and place area. TR taping

2.2

3 x 1.27 = 3.81

1.27 0.9

2.8

specifications

according to DIN

technical drawings

Not indicated tolerances ± 0.3

Pick and place area. TT taping

Footprint

(1.5)

(1.4)

Issue: 8; 02.09.09

16776

Drawing-No.: 6.544-5341.01-4

0.1

0.3

0.4

Document Number: 82177 www.vishay.com

Rev. 2.2, 23-Aug-10 7

TSOP62.., TSOP64..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE

TAPING VERSION TSOP..TT Dimensions in millimeters

100

150

200

250

300

0 50 100 150 200 250 300

t (s)

T (°C)

255 °C

240 °C 245 °

max. 260 °C

max. 120 s max. 100 s

217 °C

max. 20 s

max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s

max. 2 cycles allowed

19800

16584

www.vishay.com Document Number: 82177

8Rev. 2.2, 23-Aug-10

TSOP62.., TSOP64..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

TAPING VERSION TSOP..TR Dimensions in millimeters

16585

Document Number: 82177 www.vishay.com

Rev. 2.2, 23-Aug-10 9

TSOP62.., TSOP64..

IR Receiver Modules for Remote

Control Systems Vishay Semiconductors

REEL DIMENSIONS in millimeters

LEADER AND TRAILER Dimensions in millimeters

COVER TAPE PEEL STRENGTH

According to DIN EN 60286-3

0.1 N to 1.3 N

300 mm/min. ± 10 mm/min.

165° to 180° peel angle

LABEL

Standard bar code labels for finished goods

The standard bar code labels are product labels and used

for identification of goods. The finished goods are packed in

final packing area. The standard packing units are labeled

with standard bar code labels before transported as finished

goods to warehouses. The labels are on each packing unit

and contain Vishay Semiconductor GmbH specific data.

16734

Trailer Leader

no devices

min. 200 min. 400

StartEnd

devices

96 11818

no devices

www.vishay.com Document Number: 82177

10 Rev. 2.2, 23-Aug-10

TSOP62.., TSOP64..

Vishay Semiconductors IR Receiver Modules for Remote

Control Systems

DRY PACKING

The reel is packed in an anti-humidity bag to protect the

devices from absorbing moisture during transportation and

storage.

FINAL PACKING

The sealed reel is packed into a cardboard box. A secondary

cardboard box is used for shipping purposes.

RECOMMENDED METHOD OF STORAGE

Dry box storage is recommended as soon as the aluminum

bag has been opened to prevent moisture absorption. The

following conditions should be observed, if dry boxes are

not available:

• Storage temperature 10 °C to 30 °C

• Storage humidity ≤60 % RH max.

After more than 72 h under these conditions moisture

content will be too high for reflow soldering.

In case of moisture absorption, the devices will recover to

the former condition by drying under the following condition:

192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)

96 h at 60 °C + 5 °C and < 5 % RH for all device containers

24 h at 125 °C + 5 °C not suitable for reel or tubes.

An EIA JEDEC standard JESD22-A112 level 4 label is

included on all dry bags.

Example of JESD22-A112 level 4 label

VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)

PLAIN WRITING ABBREVIATION LENGTH

Item-description - 18

Item-number INO 8

Selection-code SEL 3

LOT-/serial-number BATCH 10

Data-code COD 3 (YWW)

Plant-code PTC 2

Quantity QTY 8

Accepted by ACC -

Packed by PCK -

Mixed code indicator MIXED CODE -

Origin xxxxxxx+ Company logo

LONG BAR CODE TOP TYPE LENGTH

Item-number N 8

Plant-code N 2

Sequence-number X 3

Quantity N 8

Total length - 21

SHORT BAR CODE BOTTOM TYPE LENGTH

Selection-code X 3

Data-code N 3

Batch-number X 10

Filter - 1

Total length - 17

Aluminum bag

Label

Reel

15973

16943

This manual suits for next models

Table of contents

Other Vishay Control Unit manuals

Vishay

Vishay TSSP57038 User manual

Vishay

Vishay TSOP62 Series User manual

Vishay

Vishay TSOP573 Series User manual

Vishay

Vishay G4-PM User manual

Vishay

Vishay TSSP570 H Series User manual

Vishay

Vishay P16TR User manual

Vishay

Vishay TSSP57038 User manual

Vishay

Vishay TSOP37 TT1 Series User manual

Vishay

Vishay P10TR User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual