Viper AS5160 User guide

Use and maintenance

Operating guidelines AS5160 series

July 2018

Turn on the key and verify

there is enough battery power

to complete the work. Charge

batteries if required.

Install the squeegee using

the thumb nuts. Attach

squeegee hose.

Remove the red cover and ﬁll

the tank. Add appropriate low

foaming detergent. Maximum

tank capacity 16 Gallons / 61

liter.

Check the level of water with

the red ball on the left side of

the machine.

Disc version: place the brush/pad holder under the scrub deck then use the pedal to lower the deck over the

brush. Press the OneTouchTM scrub button to enable scrubbing.

The vacuum will start. Push on one of the two switches ½ second to install the brush.

Boost version: attach a pad to the ﬁxed pad holder, press the OneTouchTM scrub button and the deck will

lower automatically.

Use the handle to lower or

raise the squeegee to the

ﬂoor. Adjust the squeegee

angle with the knob to adjust

suction performance if

needed.

Place the machine in working mode and

press any of the two red safety switches to

activate the machine.

Press the + or – solution buttons to

increase / decrease the water ﬂow rate

or to turn solution off.

For wheel traction version: use the rabbit /

turtle knob to control the speed of the

machine.

BOOST version: Adjust scrub pressure when

needed.

For wheel traction version: pressing either

of the red safety switches and the black

reverse button together will put the

machine into reverse.

On disc version, the brush/pad holder can

be removed automatically by raising the

deck with the pedal and then press the click

off button.

Push

on the

button

Maintenance

Operating guidelines AS5160 series

July 2018

When scrubbing is complete,

turn off the key to perform

the following maintenance.

Daily: Empty the clean water

tank using the solution tank

drain knob under the

machine.

Daily: Empty the recovery

tank using the recovery

empty hose. Bend the soft part

before removing the cap to

control the ﬂow.

Daily: Inspect and rinse the

ﬂoat ball cage and inspect

and clean the lid gasket if

required.

Local Viper dealer:

Phone number:

SN:

Daily: Remove the squeegee, and clean.

Inspect the blades and ﬂip them or replace

them if required.

Daily: to charge the battery, use the sup-

plied AC cord to the on board charger and

connect it to the machine and wall socket.

Weekly: Inspect the solution ﬁlter and

clean if required.

Daily: if the battery indicator shows red, put the machine on charge. Battery should

be on charge if empty, not in use or if not being used for coming 8-10 hours.

Daily: Leave the recovery tank lid open

after it’s been cleaned to avoid bad odor.

Other manuals for AS5160

3

Popular Scrubber manuals by other brands

Olympus

Olympus M200H operating manual

Clarke

Clarke BEXT 100H Operation?and safety

JOHNY VAC

JOHNY VAC JVC70BCT user guide

RCm

RCm Elan Series Instruction and maintenance handbook

Kärcher

Kärcher B 120 W quick start

Truvox

Truvox Orbis MotorScrubber 20 user manual

Numatic

Numatic TTB 4045/100 Original instructions

U.S. Products

U.S. Products PEX 500-C-TICK Information & operating instructions

Mclennan

Mclennan C510 Operator's manual

Tennant

Tennant T20 LPG Operator's manual

Columbus

Columbus ARA 66 BM 100 operating manual

Numatic

Numatic TTV 678G / 300T Owner's instructions

American-Lincoln

American-Lincoln 505-945 Instructions for use

FIORENTINI

FIORENTINI ET 65-75 user manual

Floorpul

Floorpul ruby 48 blt Use and maintenance

Onyx

Onyx RX-34 Operator's manual

Dustbane

Dustbane Hurricane 400 Operation manual

Sana

Sana EUJ-702 user manual