Vimar Eikon 20493 User manual
Manual to configure the radio-frequency devices when used with the burglar alarm
via bus system.
Instructions
Eikon
20493
Arké
19493
Idea
16943
Plana
14493
This manual is necessary in order to configure the radio-frequency devices when used with the VIMAR burglar alarm via bus
system through the specific radio interface (Eikon 20493, Arké 19493, Idea 16943 and Plana 14493).
WARNING: The Eikon 20493, Arké 19493, Idea 16943 and Plana 14493 radio interface is compatible with:
- By-me 8-module recess and surface mounting control panels ver. 3.0 and later.
- 2-module burglar alarm control panels ver. 5.0 and later.
- EasyTool Software ver. 4.0 and later.
SUMMARY
Radio interface (Eikon 20493, Arké 19493, Idea 16943, Plana 14493) ......................................... 2
Remote control (01819)............................................................................. 6
Infrared detector (01737) ........................................................................... 9
Detector with magnetic contact for doors and windows (01738) ............................................ 16
Water detector for protection against flooding (01744) .................................................... 24
Siren for outdoor use (01747) ....................................................................... 28
ENGLISH - 1
2 - ENGLISH
Radio interface
The radio interface allows using the radio frequency devices to
extend coverage in places or accesses where it is not possible to
add any cables and devices via BUS. In addition it permits using
one or more radio controls as a key to switch the system on/off.
The device turns the system on and off (completely or the asso-
ciated partitioned zones) after receiving the code emitted by the
remote controls.
Iì’t is supplied in the following versions:
20493: 2 Eikon modules
19493: 2 Arké modules
16943: 2 idea modules
14493: 2 Plana modules
Technical characteristics
- Rated supply voltage (Vn): BUS 20-30 V d.c.
- Protection class: IP30
- Operating temperature: -5 -- +45 °C (for indoor use)
- Installation: flush or surface mounting (with surface mounting box
09975…)
- Type of protection: against opening and removal with passive infrared
sensor built in
- Consumption: 20 mA typ
-
Frequency of reception and transmission: dual at 433 MHz and 868 MHz
- Configuration button
- Indicator LED
- It has two terminals for the polarized connection to the bus (+ and –).
- The receiver is governed, for turning the system on and off and parti-
tioning it, by one or more remote controls with over 65,000 possible
combinations.
- Maximum number of radiofrequency devices that can be stored: 40
for each radio interface
- Maximum number of radio interfaces that can be installed in a
system: 4.
IdeaEikon Plana
Arké
ENGLISH - 3
List of Radio frequency devices that can be used
VIMAR code DESCRIPTION / COMPOSITION
01819 Two-way remote control
01737 Passive infrared intrusion detector, battery power supply (supplied).
01738 Magnetic contact for doors and windows, battery power supply (supplied).
01744 Water detector for protection against flooding, battery power supply (supplied).
01747 Siren for outdoor use, battery power supply (supplied)
00912 9 V 12 Ah alkaline battery for siren for outdoor use
N.B.: The detectors 01737 and 01738 are equipped with an input terminal on which an NC or a roller-shutter contact can be
connected; to enable it, use the dip switches on the device card.
4 - ENGLISH
Operation
The device receives the transmissions of the radio wave signals
emitted by the radiofrequency devices and by the remote control.
• Regular operation: receives the information from the radiofre-
quency devices (tamper alarm, burglar alarm, technical alarm,
low battery). It receives the codes from the remote controls and
sends them to the control panel; in addition it receives informa-
tion from the control panel on the system status and sends it to
the siren and remote controls.
• Configuration:inthephaseofaddingradiofrequencydevicesit
saves the characteristics of the component that has responded
and communicates some information to the control panel.
• Supervision: this function checks the configured Radio
Frequency devices work properly; If a device does not signal
its presence for a time of 4 h, the interface sends a “no devi-
ce” message to the control panel. To obtain this function the
“Supervision” parameter must be active.
Note: If the intrusion detection alarm system is turned on and a
contact has accidentally been left open (a window for instance),
the system will not turn on and the control panel will display the
alarm message and the zone to which the contact left open
belongs.
If you repeat the process for turning it on, the system will activate
itself as normal even with the contact open.
Indicators
• redLEDonsteady:
- during configuration and reset;
• redLEDblinking:
- due to system in alarm or an attempt at tampering with the
device. The LED keeps on blinking until the alarm that generated
it is deleted or the system is turned on again; therefore it is not
enough to turn off the system to cut off the alarm.
• greenLEDblinking:
- the system is turned on in partitioned mode;
• greenLEDonsteady:
- the system is turned on not partitioned;
ENGLISH - 5
• red/greentwo-colourLEDblinking:
- it blinks for a few seconds after the phase of resetting the device.
Settings (programmable via the control panel)
1) Zone: the assignment zone from 1 to 30, set from the control
panel by selecting the number of the chosen zone in the spe-
cific menu; the interface can be configured in zone 31 when
you need the “PANIC” button of the remote control 01819 to
activate the audible panic alarm (see page 6).
2) Sensitivity of the antitamper device: (default 0 that is disabled).
Value that adjusts the sensitivity of the optical antitamper in
the radio interface. Adjustment range from 0 (disabled) to 15
(maximum sensitivity);
3)
Supervised (default OFF). Supervision of the Radio Frequency
detectors on (ON) or off (OFF);
4) Activation delay zones from 1 to 10: 0 s = instantaneous. It can
be increased up to 60 s in steps of 1 s;
5) Activation delay zones from 10 to 20: 0 s = instantaneous. It can
be increased up to 60 s in steps of 1 s;
6) Activation delay zones from 20 to 30: 0 s = instantaneous. It can
be increased up to 60 s in steps of 1 s.
Note:If a radio frequency detector for alarms of a technical type
(water detector, for instance) is configured in the same zone as a
relay actuator (one-position stable), this will switch over when the
detector signals the alarm.
Standard compliance
R&TTE directive
Standards EN 60065, EN 50130-4, EN 61000-6-3, EN 301489-1,
EN 301489-3, EN 300220-2.
6 - ENGLISH
The remote control has 4 keys to transmit 4 different com-
mands to the radio interface. The radio interface commu-
nicates these commands to the control panel. Command
transmission is indicated by the orange LED of the remote
control lighting up.
Remote control (01819)
OFF button
Control transmission
and confirmation LED
ON 1 button
PANIC button
01819
ON 2 button
Technical characteristics
- Power supply: 2 alkaline batteries 3 V CR2016
- Radio range: 100 m in an open field
Standard compliance
R&TTE directive
Standards EN 60950-1, EN 50130-4, EN 301489-1, EN 301489-3,
EN 300220-2.
Operation
Pressing the 4 keys on the remote control provides 4 different
functions.
•OFFbutton1:Turningthesystemoff(accordingtothepartitions
associated with the remote control code).
• ON1button2:Turningthesystemon(accordingtothepartitions
associated with the remote control code).
• PANICbutton3:usedtomanagethepanicsignal.
• ON2button4:Switchesthesystemon(accordingtotheparti-
tions associated with the control).
ENGLISH - 7
LED indicators
• blinkingorange:codetransmission
• green:systemofforinterfaceinoffzone
• red:systemonorinterfaceinactivezone
The remote control has the function of a connector; in addition, for
button 3 it is possible to select:
PANIC BUTTON function with audible warning: the radio interface
must be configured in zone 31. In this way, on pressing the PANIC
button the siren is activated.
PANIC BUTTON FUNCTION WITHOUT AUDIBLE WARNING but
with message: the radio interface and an actuator must be configu-
red in the same zone from 1 to 30. The actuator must be connected
to a channel of the dialler. In this way, on pressing the PANIC button
the message is sent.
MANAGEMENT FUNCTION: the radio interface and an actuator
must be configured in the same zone from 1 to 30. In this way, on
pressing the PANIC button the state of the actuator is switched over
(one-position stable actuator).
The various PANIC functions are mutually exclusive.
To silence the sirens turn the system on and off with the remote control
by pressing the ON (1 and 2) and OFF buttons in sequence, or on the
control panel with “Alarm Reset”
Configuring the remote control
- Prepare the control panel for configuring the radio-frequency devices
(see the control panel manual).
- Press remote control buttons 1 and 2 together.
8 - ENGLISH
Inserting/changing batteries.
The power supply is provided by 2 alkaline batteries CR2016 3 V.
• Changethebatteriessolelywithonesofthesametype.
• Connectthebatteriesobservingthecorrectpolarity.
• Ifscrappingtheremotecontrol,thebatteriesmustbetaken
out beforehand.
WARNING:
Dispose of batteries in the specific differentiated
collection bins.
CR 2016
3V
CR 2016
3V
CR 2016
3V
This manual suits for next models
3
Table of contents
Other Vimar Control Unit manuals
Vimar
Vimar 03981 User manual
Vimar
Vimar BY-ALARM PLUS User manual
Vimar
Vimar by-me Eikon Evo 21509 User manual
Vimar
Vimar ELVOX ECG1 User manual
Vimar
Vimar Eikon 20635 User manual
Vimar
Vimar BY-ALARM PLUS User manual
Vimar
Vimar Elvox 8051/0 Assembly instructions
Vimar
Vimar Eikon User guide
Vimar
Vimar ELVOX SW24.W User manual
Vimar
Vimar by-me Eikon 20540 User manual
Vimar
Vimar BY-ME PLUS 01483 User manual
Vimar
Vimar 03905 User guide
Vimar
Vimar by-me Eikon Evo 21509 User manual
Vimar
Vimar ELVOX EMC.W User manual
Vimar
Vimar ACTO 404D User manual
Vimar
Vimar ELVOX SL230.T User manual
Vimar
Vimar by-me Eikon 20521 User manual
Vimar
Vimar Elvox RS15 User manual
Vimar
Vimar Elvox 6153/682 Assembly instructions
Vimar
Vimar SL24.W User manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
