Viking Range VDUO5241 Instructions for use

Install / Use & Care

MANUAL

5 SERIES

Outdoor Refrigerated Drawers

VDUO5241

NOTE

!CAUTION

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product Dimensions ...........................................................8

Using your Electronic control ............................................10

Care and cleaning .............................................................11

Long term storage / winterization ................................ 11

Stainless steel maintenance ............................................12

Energy saving tips ............................................................12

ServiceInformation.............................................................14

Troubleshooting ................................................................15

Warranty .......................................................................... 16

!WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Important Safety Instructions

Warnings and safety instructions appearing in this

guide are not meant to cover all possible conditions and

situations that may occur. Common sense, caution, and

care must be exercised when installing, maintaining, or

operating this appliance.

Recognize Safety Symbols,

Words, and Labels.

!WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could

result in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

NOTE

!CAUTION

XXXXXXXXXXXX

VIKING RANGE, LLC

GREENWOOD, MS 38930

UNPACKING YOUR APPLIANCE

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.vikingrange.com

The following information will be

required when registering your

appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See ¿gure 1).

!WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding

internal components in place. The owners manual is

shipped inside the product in a plastic bag along with the

warranty registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance

has been thoroughly inspected and found to be in good

condition. If there is damage, the packaging will be needed

as proof of damage in transit. Afterwards please dispose of

all items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the

appliance to sit upright for a period of at least 24 hours

before plugging in. This will assure oil returns to the

compressor. Plugging the appliance in immediately may

cause damage to internal parts.

Figure 1

Online registration

available at

www.vikingrange.com

!WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

!CAUTION

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources.

To ensure your product performs to speci¿cations, the

recommended installation location temperature range is

from 5to 1°F (1to °C).

Cabinet Clearance

Ventilation is required from the bottom front of the

appliance. Keep this area open and clear of any

obstructions. Adjacent cabinets and counter top can be

installed around the appliance as long as the front grille

remains unobstructed.

Front Grille

Do not obstruct the front grille. The openings within

the front grille allow air to Àow through the condenser

heat exchanger. Restrictions to this air Àow will result in

increased energy usage and loss of cooling capacity. For

this reason it is important this area not be obstructed and

the grille openings kept clean. Viking Range,LLC does not

recommend the use of a custom made grille as air Àow may

be restricted. (See Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR APPLIANCE

Leveling Legs

Adjustable legs at the front and rear corners of the

appliance should be set so the unit is ¿rmly positioned on

the Àoor and level from side to side and front to back. The

overall height of your appliance may be adjusted between

the minimum, 333»4" (85.7 cm), by turning the leveling leg in

(CW ඟ) and the maximum, 343»4" (88.3 cm) by turning the

leveling leg out (CCW ඞ.

To adjust the leveling legs, place the appliance on a solid

surface and protect the Àoor beneath the legs to avoid

scratching the Àoor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the

appliance forward using caution. On a level surface check

the appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille

adjusted to the desired height. When adjustment is

complete tighten the two front grille screws. (See Figure 5).

NOTE

Figure 6

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any

circumstances, be installed to an un-grounded

electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must

be plugged into a mating grounding type receptacle

in accordance with the National Electrical Code and

applicable local codes and ordinances (see Figure 6). If the

circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to provide the

proper power supply. The third ground prong should not,

under any circumstances, be cut or removed.

Ground Fault Circuit Interrupters (GFCI) are prone to

nuisance tripping which will cause the appliance to shut

down. GFCI’s are generally not used on circuits with power

equipment that must run unattended for long periods of

time, unless required to meet local building codes and

ordinances.

Front grille screw

Front grille

Figure 5

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

!CAUTION

NOTE

Bottom View of

Refrigerator

Anti-Tip

Bracket Leveling Leg

Front of cabinet

211»2"

(54.6 cm)

Figure 7

Floor Mount Installation

The anti-tip bracket is to be located on the Àoor in the left or

right rear corner of the refrigerator as shown in Figure 7.

Step by step instructions for locating the

position of the bracket:

1) Decide where you want to place the refrigerator. Slide it

into place, being careful not to damage the Àoor, leaving 1"

(2.5 cm) of clearance from the rear wall to allow room for

the anti-tip bracket.

2) Raise the rear leveling legs approximately 1»4" (6 mm)

to allow engagement with the anti-tip bracket. Level the

unit by adjusting all the leveling legs as required. Turning

the leveling leg counterclockwise will raise the unit and

clockwise will lower the unit.

3) Make sure the refrigerator is in the desired location, then

mark on the Àoor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the Àoor marking the front corner

of the cabinet, excluding the door. Slide the refrigerator out

of the way. From the temporary line extend the sidewall line

back 211»2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the Àoor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 211»2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the Àoor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the

rear cabinet leveling leg slides under the anti-tip bracket

engaging the slot.

!WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE

INSTRUCTIONS BELOW

Any ¿nished Àooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete Àoor, concrete fasteners are

required, (not included with the anti-tip kit).

Anti-Tip Device

!WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

211»2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Side of cabinet line

Figure 8

Front of cabinet line

Rear of cabinet line

Rear Leveling leg

Screw

Figure 8a

NOTE

When the Àoor mounted anti-tip bracket is used the

minimum adjusted height of the cabinet is increased by

3»8" (9 mm).

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

VDUO5241 24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm) *237»8"

(60.7 cm)

333»4" to 343»4"

(85.7 to 88.3 cm)

2323»32"

(60.2 cm)

267»32"

(66.6 cm)

4613»32"

(117.9 cm)

261»4"

(66.7 cm)

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-

in opening a hole can be cut through the adjacent

cabinet and the power cord routed through this hole to

a power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord

plug. Not all recessed outlet boxes will work for this

application as they are too narrow, but a recessed

outlet box equivalent to Arlington #DVFR1W is

recommended for this application, (see Figure 10).

* Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire door "F"

dimension plus 1" (2.5 cm) for thickness of power cord plug is required.

** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet.

PRODUCT DIMENSIONS

Figure 10

Figure 9

Figure 9a

"F"

211»2"

(54.6 cm)

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

VDUO5241 115V/60Hz/15A 140 lbs

(63.6 kg)

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 11

!WARNING Floor mount Anti-tip Bracket must be installed for freestanding

applications. Not required for built in applications.

# A grounded 15 amp dedicated circuit is required.

Follow all local building codes when installing electrical

and appliance.

Figure 10

Control Function Guide

Function Command Notes

ON/OFF Press and release. Unit will immediately turn ON or OFF.

Adjust Temperature Press or and release.

When the display is ashing, press or to adjust the set

point temperature. Note: temperature displayed is the actual

temperature inside unit.

Toggle Between oF / oC Hold and for 5 seconds. The display will change units.

Leave Interior Light On Press and release to leave interior light on for

12 hours; press again to deactivate.

After 12 hours, factory default is restored; light will turn on when

door is open.

Adjust Light Color While holding , press and release to scroll

through lighting options.

Option Open Door Closed Door

White White

Blue Blue

White Blue

Light will be set at full intensity when door is open, and 50%

intensity when door is closed.

Enable Sabbath Mode Press and hold for 5 seconds and release.

The oF / oC symbol will ash briey after 5 seconds. Interior

light and display will go dark and remain so until user resets

mode - unit continues to operate.

Disable Sabbath Mode Press and release. Display and interior light return to normal operation.

Door Alert Notication

When the door is left open for more than 30 minutes:

• A tone will sound for several seconds every minute

• will appear in display

• Close door to silence alert and reset

Temperature displayed reects actual temperature inside unit. If the

temperature displayed is di󰀨erent than selected, the unit is progressing

towards the selected temperature. Time to reach set point varies based

upon ambient temperature, temperature of product loaded, door openings,

etc. Viking recommends allowing the unit to reach set points before loading.

NOTE

Figure 11

USING YOUR ELECTRONIC CONTROL

This manual suits for next models

Table of contents

Other Viking Range LCD Drawer manuals

Viking Range

Viking Range VEWD172 User manual

Popular LCD Drawer manuals by other brands

Acnodes

Acnodes KD 8228 user manual

Ameriwood

Ameriwood 9524328PCOM manual

Kesseböhmer

Kesseböhmer TANDEM solo Mounting instructions

Crystal Image Technologies

Crystal Image Technologies RMD-151-A Series user manual

APW Wyott

APW Wyott Ease Extreme HDX-1-120 Installation and operating instructions

NTI

NTI RACKMUX-V17-N Installation and operation manual

Austin Hughes

Austin Hughes CyberView L120 user manual

Uplift Desk

Uplift Desk STR018 manual

Acnodes

Acnodes KDC 81932 user manual

Acnodes

Acnodes RK1200T user manual

StarTech.com

StarTech.com DuraView RACKCONS1501 instruction manual

Mocka

Mocka Mischa Assembly instructions

GRASS

GRASS DWD XP manual

StarTech.com

StarTech.com DuraView RACKCONS1701 instruction manual

Fisher & Paykel

Fisher & Paykel IZONA CoolDrawer RB36S installation instructions

Synergy Global Technology

Synergy Global Technology LCD1U17-44 user manual

Fujitsu

Fujitsu RC25 user manual

Acnodes

Acnodes RK 1000B installation guide