Vidao VXA980T User manual

Tilting, Swiveling & Rotating

Flat Panel Wall Mount

• Supports most 40”- 80” Flat Panel TVs

Model: VXA980TC

+5 to -5

+5 to -15

For technical assistance or troubleshooting

please call 1-855-998-4326.

This product Wall Mount frame is intended for use only with an apparatus which has a maximum weight of 132 lbs. See apparatus

instructions. Using with an apparatus heavier than the maximum weight indicated may result in instability and cause possible

injury.

READ THIS FIRST

Read this entire manual! Do not attempt to install this product if you do not understand the instructions. Contact a qualified

mount installer if you have any doubts about a safe and secure mount installation, or if you are not sure what specific wall

materials you are attaching this mount to. Check all the parts carefully to make sure there are no missing or damaged parts.

Improper installation may result in damage to your TV, property, and personal injury.

• Maximum Weight Capacity: 132 lbs.

• Supports VESA Sizes up to 600x500

This product is intended only to mount a television of the indicated size and weight. Using this

product to mount televisions heavier than the maximum weight capacity can damage equipment

and cause personal injury.

Schoenfeld International Inc. and VIDAO are not responsible for personal injury or product

damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of this

product.

How and where you use your television wall mount is extremely important for Child Safety

As you set up and use your new product, keep all of these safety tips in mind.

• One size of TV wall mount does not fit all TVs. Use only a TV wall mount rated for the weight

of your TV and the size of your screen. Your TV wall mount assembly instructions contains

specific information on the maximum weight and screen size combination that your wall

mount can safely support. Do not exceed the maximum weight of screen size for any TV wall

mount.

• Carefully read all of enclosed instructions for proper use of this product. If you have any

doubts about safe and secure assembly, please contact a professional.

• Don’t let children climb on or play with mounts or TVs.

• Remember that children can become excited while watching a program, especially on a

“larger than life” TV. Make sure to place or install the TV wall mount where it cannot be

pushed, pulled on, or knocked down.

• Make sure that you route all cords and cables so that they cannot be pulled or grabbed by

curious children.

Always wear safety goggles to when drilling or installing hardware.

Tools

For your convenience, we have included an allen wrench with this mount. For the best assembly

experience and mounting safety, we always recommend using full-size tools for each assembly

step.

Below is a recommended tool list you will need for proper and safe installation. See applicable

warnings in this manual about certain types of mounting surface materials and the special hardware

and tools that should be used.

• Drill with a specific size drill bit to pre-drill holes in the wall

• Stud finder

• Tape measure

• Pencil

• Screw drivers

• Socket wrenches

• Small hammer

• Safety goggles

Wall Mount Bracket

M4x30mm bolts

M5x20mm bolts

M5x30mm bolts

22mm Spacers

17mm Spacers

M8x45mm Bolts

M8x25mm Bolts

M4x20mm bolts

M6x25mm bolts

M6x40mm bolts

M4/M5 Washers

M6/M8 Washers

Socket Tool

Allen Wrench

B64

Wall Mount

Brackets

Security Bracket Clamps

Long Bolts

Long Bolt Washers

Concrete Anchors

Security Bracket Clamp Screws

G4Level (Attached to Wall Mount)

Concrete Anchors

Ax6 Bx6 Cx6

Long Bolts

Long Bolt

Washers

Qx4

Security Bracket

Clamp Screws

M5x12mm

x14

Allen Wrench with Phillips End

Security Bracket Clamps

x1 R-Level

x25

Mounting Plate

Side Pieces

S 4 Side Piece Screws

Sx4

Side Piece

Screws

Slide the Mounting Plate Side Pieces (5) onto the ends of the Wall Mount (1).

Step 1: Attach the side pieces to the mounting plate

Secure the Mounting Plate Side Pieces (5) to the Wall Mount (1) using the Allen Wrench and

the Side Piece Screws (S).

Attach the Brackets (2) to the rear of the TV using four of the Bolts (D-K) with the proper size

Washers (N-O) as shown in Fig. 1a. Make sure to use the same bracket holes for each side to insure

the Brackets (2) are centered top-to-bottom. Tighten using the Allen Wrench (4). Do not over tighten.

Do not force the bolts into the mounting holes on your TV. Do not use an electric drill to

tighten these bolts on your TV. This could damage the equipment or cause personal injury.

CAUTION: Do not place the TV face down on a hard surface when installing the mounting plate

on the TV. Placing the TV face down on a hard surface can result in equipment damage. Use a

blanket or other suitable surface.

If your TV has a flat straight rear, and your screen size is 55” or less, spacers are most likely not

necessary.

The Brackets (2) must be installed on the TV with the hook on each bracket facing down.

N-O

D-K

N-O

D-K

Step 2: Attach the left and right brackets to your TV

Fig. 1b

Attach the TV Bracket to the rear of the TV cont’d

Fig. 1c

D-K

L-M

N-O

If your television has a curved back, and the mounting holes are recessed (Fig 1b) spacers are

required. Install the proper size Spacers (L-M) between the TV rear and the bracket structure as

shown in Fig 1b. to make sure the Brackets (2) extend past the rounded portion of the TV. Then use

the selected Bolts (D-K), Washers (N-O), and the Allen Wrench (4) to attach the bracket structure

(with the spacers between the bracket and the TV) to the TV as shown in Fig 1c. Make sure the

bracket structure is properly aligned on the rear of the TV and securely tighten the bolts. Do not over

tighten.

Fig. 1d

N-O

L-M

D-K N-O

L-M

D-K

L-M

Step 3: Find and mark the best position for the wall mount on the wall

Step 4: Attach the wall mount to the wall

Fig. 3a

2-1/2” (65mm)

Fig. 3b

Fig. 3c

1. Use a pencil, awl, or a nail to mark the location of the wall stud centers (Fig 3a) after locating the

stud with an electronic stud locator. The distance between the marks should not be less than 16

inches (Studs must not be less than 16 inches (40.6cm)

2. Place the Wall Mount (1) flat against the wall with the center of the mount in the desired location,

aligning the holes in the mount with the studs (Fig 3b). Use the wall mount plate as a template to

mark the location of the four mounting holes on the wall. Make sure that the mounting holes are

level and are parallel using the built-in level on the front of the Wall Mount (1).

3. Use 3/16” (5mm) drill bit to pre-drill holes at least 2.5” (65mm) deep at the marked locations.

4. Use a wrench, the four Long Bolts (A), and Washers (C) to attach the wall mount to the wall. Do not

use wall anchors in wood stud walls.

5. Use the Level (R) placed on the front of the mounting plate to level the wall mount, repositioning as

necessary, then firmly tighten the bolts. Do not overtighten.

2.5” (65mm)

Fig. 3d

Fig. 3e

Step 5: Hang the television display

1. Place the Wall Mount (1) flat against the wall in the desired location. Use the wall plate as a

template to mark the location of the four mounting holes on the wall. Make sure that the mounting

holes are level and parallel. Make sure the horizontal holes are no closer than 16”.

2. Use 3/8” (10mm) drill bit to pre-drill four holes at least 2.5” (65mm) deep (Fig 3d) at the

marked locations.

3. Insert a Wall Anchor (B) into each pre-drilled hole and lightly tap it with a hammer until the wall

anchor is flush with the wall.

4. Use a wrench, the four Long Bolts (A), and Washers (C) to attach the wall mount to the wall with

the Wall Anchors (B) (Fig 3f).

5. Use the Level (R) placed on the front of the mounting plate to level the wall mount, repositioning as

necessary, then securely tighten the bolts.

Fig.3f

Concrete wall

A large television requires two people to lift. Schoenfeld International Inc. and VIDAO are not

responsible for equipment damage or personal injury due to mishandling.

1. Lift the Television display with the brackets attached and carefully hang the top hook of the

Brackets (2) over the top bar of the Wall Mount (1) as shown in (Fig. 4a). Carefully swing the display

down so the lower part of the Brackets (2) fit over the lower bar of the Wall Mount (1).

2. Securely attach the Security Bracket Clamps (3) to the Brackets (2) using the Security Bracket

Clamp Screws (Q) and the phillips end of the Allen Wrench (4)(Fig. 4b).

Fig 4a

Fig 4b

Table of contents

Other Vidao Rack & Stand manuals

Vidao

Vidao V5760STC User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 