Vicon VM-717LCD User manual
Vicon Part No. 8009-8198-00-00 Rev 1008 Section 2
XX198-00-00
VM-717LCD and VM-719LCD
Flat Panel LCD Monitors
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your
requirements or that the operation will be entirely error free or perform precisely as described in the
documentation. This system has not been designed to be used in life-critical situations and must not
be used for this purpose.
Copyright © 2008 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 WEB: www.vicon-cctv.com
Important Safeguards – Indoor Use
GRAPHIC SYMBOL EXPLANATION
The lightening bolt symbol alerts the user to the presence of
dangerous voltage that may present the risk of electric shock.
The exclamation point symbol alerts the user to the presence of
important operating and maintenance instructions.
WARNING
To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
1. Read Instructions - Read all safety and operating instructions
before the product is operated.
2. Retain Instructions - Retain all safety and operating
instructions for future reference.
3. Heed Warnings - Pay attention to all product warnings.
4. Follow Instructions - Follow all operating instructions.
5. Cleaning -(Do not use caustic, abrasive or aerosol
cleaners)
a) For units that CAN BE DISCONNECTED from the power
source, use a damp cloth for cleaning.
b) For units that CANNOT BE DISCONNECTED from the
power source, use a damp cloth for cleaning and do not
allow moisture or liquids to enter vents.
6. Attachments - Use only UL Listed Vicon recommended
attachments to prevent unit damage and personal injury.
7. Water and Moisture - Use only products designed for outdoor
environments where they will be exposed to water or moisture.
8. Accessories - Do not place the unit on an unstable surface to
avoid falling. Use only UL Listed Vicon recommended mounting
accessories.
9. Ventilation - Do not block ventilating slots and openings as
they ensure reliable operation. Do not place the unit near a heat
source or into an enclosure unless recommended by Vicon.
10. Grounding - Only products equipped with a 3-prong
grounded plug should be inserted into a grounded power outlet.
Contact an electrician to replace an obsolete outlet. Do not force
a plug into a non-grounded outlet.
11. Power Cord Protection - Power supply cords should not be
routed in trafficked areas or in tight spaces where they will be
pinched or used to bear weight. Allow some slack in the cord
where it enters the unit.
12. Lightning - Disconnect the product from its power source and
cable system when possible to prevent damage due to lightning
and power-line surges.
13. Power Lines - Do not locate outside cables over power or
utility lines where they can fall and make direct contact. Contact
with power lines can be fatal.
14. Overloading - Do not overload wall outlets and extension
cords to prevent risk of fire and electric shock.
15. Object and Liquid Entry - Never probe through, or spill liquid
into, enclosure openings to prevent risk of fire or electric shock.
16. Servicing - Refer all servicing to qualified service personnel.
17. Damage Requiring Service - Obtain service when:
a) The power-supply cord or plug is damaged.
b) Objects have fallen or liquid has been spilled into the
product.
c) The product is not designed for outdoor use and has been
exposed to water or moisture.
d) The product does not operate per the operating instructions.
Perform Vicon recommended adjustments, modifications
and troubleshooting only to avoid unit damage and personal
injury.
e) The product has been dropped.
f) The product shows a significant change in performance.
18. Replacement Parts - Use only Vicon specified replacement
parts or an approved equivalent to prevent unit damage and
injury.
19. Safety Check - Request safety checks to be performed
following repair or maintenance to verify proper operation.
20. ESD Precaution - Take all normal electrostatic discharge
precautions to avoid component damage during installation and
operation.
21. For 230 VAC Devices Only - When the disconnect device is
not incorporated in the equipment or when the plug on the power
supply is intended to serve as the disconnect device, follow the
guidelines below:
a) For permanently connected 230 VAC units, a readily
accessible disconnect device must be incorporated into the
site wiring.
b) For 230 VAC units with a plug, the outlet must be installed
near the unit and be easily accessible.
FCC Notice
Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart
B for a Class A digital device.
WARNING
This equipment generates and uses radio frequency energy and if not installed and used
properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference
to radio and television reception. It has been type tested and found to comply with the limits for a
Class A computing device in accordance with the specification in subpart B of part 15 of the FCC
rules, which are designed to provide reasonable protection against such interference in a
commercial installation. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and television reception,
which can be determined by turning equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
•Reorient the receiving antenna.
•Relocate the equipment with respect to the receiver.
•Relocate the equipment away from the receiver.
•Plug the equipment into a different electrical outlet so that the equipment
and receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for
additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission
helpful:
“Interference Handbook, Bulletin CIB-2”
This booklet is available from the U.S. Government Printing Office, Superintendent of Documents,
Mailstop SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1.
Warning: Power must be removed from this unit before removing circuit modules or cables.
Caution: This unit contains circuit cards with integrated circuit devices that can be damaged
by static discharge. Take all necessary precautions to prevent static discharge
Introduction | 1
VM-717/719LCD Monitors XX-198-00
Installation and Operation
This manual describes the installation and operation of the Vicon® VM-
717LCD and VM-719LCD monitors.
The chapter consists of the following topics:
Topic Page
Introduction 2
Connectors 3
Mounting 4
Controls 6
Onscreen Display Operation 9
Maintenance 21
Technical Specifications 25
2| Installation and Operation
XX-198-00 VM-717/719LCD Monitors
Introduction
This manual provides installation and operation instructions for the Vicon
models VM-717LCD (Product Code 8776-50) and VM-719LCD (Product
Code 8776-60) monitors. The monitors have a resolution of 1280x1024 @ 60
Hz and accept NTSC or PAL television systems.
The monitors are easily operated from front panel buttons. Controls include a
power switch and indicator; SOURCE (video input) selection; AUTO
geometry adjustment: cursor and adjustment up and down, Volume controls,
infrared sensor for the remote control and a MENU button for the on screen
display. Connectors for power, video, audio and external equipment are
located on the bottom of the monitor.
The following paragraphs describe the monitors, installation and operation.
Accessories
Included:
Power cord
PC cable
AC Adaptor – Converts line voltage to 12 VDC, product code 8776-75
Optional:
Wall mount – Uses standard VESA wall-mount kit.
Rack mount, Vicon model VM-7179LCD-RK, product code 8776-65
Remote Control and Batteries, product code 8776-70
Connectors | 3
VM-717/719LCD Monitors XX-198-00
Connectors
The connectors are located on the bottom of the monitor. They are described
in the following table.
Index Number Description
1 12 VDC power input.
2 D-Sub connector VGA input.
3 Video 1 Input: composite video input.
4 Video 1 Output: looping output for Video 1.
5 Video 2 Input: composite video input.
6 Video 2 Output: looping output for Video 2.
7, 8 Audio inputs: stereo (L+R).
9 S-Video (Y/C) Input: Y/C separated signal input.
10 S-Video (Y/C) Output: Y/C separated signal output.
11 PC stereo input
4| Installation and Operation
XX-198-00 VM-717/719LCD Monitors
Mounting
The monitors are provided with an easel stand for table mounting, and may
be wall or rack mounted using optional accessory kits.
Wall Mounting
You can wall-mount the monitor using the 100 mm precut holes or a standard
VESA wall-mount kit.
Mounting | 5
VM-717/719LCD Monitors XX-198-00
Rack Mounting
The Rack mounting kit is provided with an installation guide. Refer to the
guide for mounting instructions.
6| Installation and Operation
XX-198-00 VM-717/719LCD Monitors
Controls
Front Panel
Index Number Description
1 SOURCE: selects input source (VGA, Composite 1 or 2 or
S-Video).
2 MENU: activates or exits the Onscreen Display (OSD).
Also used to move to a previous menu or status.
3 AUTO: Automatically adjusts geometry of PC source. In
menu mode, moves cursor down.
4 Up cursor control. Moves cursor up in menu mode.
5 VOL: Lowers or raises volume. In menu mode, moves
cursor left or right.
6 IR sensor receives signals from optional remote control.
7 Power On/Off and power indicator.
Other manuals for VM-717LCD
1
This manual suits for next models
3
Table of contents
Other Vicon Monitor manuals
Vicon
Vicon VM-632LCD-1 User manual
Vicon
Vicon VM-624LED User manual
Vicon
Vicon VM-642LED User manual
Vicon
Vicon VM-619LCD Administrator Guide
Vicon
Vicon VM617 User manual
Vicon
Vicon VM-610LCD Operating instructions
Vicon
Vicon VM614-2 User manual
Vicon
Vicon VM615-4 User manual
Vicon
Vicon VM621-4 User manual
Vicon
Vicon VM-620LCD User manual
