Vertiv Liebert APS User manual
590-1563-501A/SL-55016_REV1_3-17
1
LIEBERT® APS™
MODULE REPLACEMENT
Quick Installation Guide
These instructions apply to the
replacement or addition of the
following modules:
• Power module
• Battery module
• Charger module
• System control module
• System monitoring module
BATTERY, POWER, AND
CHARGER MODULE
REMOVAL
WARNING
:
Risk of heavy unit
falling over. Can cause equipment
damage, injury or death. Read all of the
instructions before attempting to move,
lift, remove packaging, or prepare the
unit for installation. The UPS represents
a tipping hazard.
Do not remove more than one module
at a time. Failure to do so may cause
unit to tip over and cause serious injury.
To locate a faulty module, remove the
bezel cover and look for an illuminated
yellow “fault” LED, which indicates a
faulty module.
If the removed bezel(s) have air filters,
replace them at this time.
NOTE
: If your system does not contain
a redundant module, place the UPS into
manual bypass mode before removing
modules to prevent accidental loss of
power to the connected equipment.
1. Removing the
module‑securing bracket
Use a Phillips-head screwdriver to
remove the fastener (if installed).
2. Releasing the lock lever
Pull out the lock lever slightly and
lift up, then wait a few seconds
before continuing.
3. Removing the module
from the cabinet bay
Slide the module out about
two-thirds of the way until it is
stopped by the safety catch.
Lift the module slightly and, while
supporting the module, slide it
completely out.
1
2
3
590-1563-501A/SL-55016_REV1_3-17
2
LIEBERT® APS™ MODULE REPLACEMENT
Quick Installation Guide
BATTERY, POWER, AND
CHARGER MODULE
INSTALLATION
4. Inserting a module
into a cabinet bay
Lift the module to the appropriate
bay, resting the end of the module
on the bay shelf.
NOTE
: Do not rest the module on
any plastic bezels. It could damage
the bezel.
NOTE
: Two battery modules must
be installed in the same row to
complete the battery string.
Slowly push the module in until
about one-third of the module is in
the bay.
Lift the module up, then continue
pushing until about 5 cm (2 in.) of
the module remains outside the bay,
then push it firmly and smoothly to
ensure that it is fully inserted.
5. Engaging the lock lever
Pull out the lock lever slightly
and press the lever down into the
bracket.
NOTE
: If the lever does not press
down smoothly, remove and reinstall
the module.
6. Attaching the
module‑securing bracket
Use a #2 Phillips-head screwdriver
to install the module-securing
bracket.
7. Replace the plastic bezel(s).
4
5
4
590-1563-501A/SL-55016_REV1_3-17
3
LIEBERT® APS™ MODULE REPLACEMENT
Quick Installation Guide
SYSTEM CONTROL OR
SYSTEM MONITORING
MODULE REMOVAL
CAUTION
:
When both a control
and monitoring module need replaced,
do not remove them at the same time.
If both are removed, the UPS shuts
down and power is removed from
the connected equipment unless
the system includes an external
maintenance-bypass system, and the
UPS is operating in maintenance-
bypass mode.
1. Remove the display bezel
and the LCD display.
Lay the display module on top
of the UPS.
2. Freeing the module
Use a Phillips-head screwdriver
to remove the screws from the
2 securing holes.
3. Releasing the lock lever
Pull out the lock lever slightly
and pull to the left, then wait a few
seconds before continuing.
4. Removing the module
Being sure to support the module,
slide it completely out of its control
bay.
NOTE
: These modules do not have
a safety catch because they are
lightweight.
SYSTEM CONTROL OR
SYSTEM MONITORING
MODULE INSTALLATION
5. Inserting a module
into a control bay
Push the module in until about 1
cm (1/2 in.) of the module remains
outside the bay, then push it firmly
and smoothly to ensure that it is
fully inserted.
6. Engaging the lock lever
Pull out the lock lever slightly and
press the lever to the right into
the bracket.
7. Re‑attaching the module
to the cabinet
Use a #2 Phillips-head screwdriver
to resecure the module.
8. Replace the LCD display
and the display bezel.
1
2
3
4
5
4
6
VertivCo.com |Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA
© 2017 Vertiv Co. All rights reserved. Vertiv and the Vertiv logo are trademarks or registered trademarks of Vertiv Co. All other names and logos referred to are trade names, trademarks or
registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no responsibility, and disclaims all
liability, for damages resulting from use of this information or for any errors or omissions. Specications are subject to change without notice.
590-1563-501A/SL-55016_REV1_3-17
4
Other Vertiv UPS manuals
Vertiv
Vertiv Liebert EDGE Series Installation and maintenance instructions
Vertiv
Vertiv Liebert MicroPOD Installation and maintenance instructions
Vertiv
Vertiv Liebert APM User manual
Vertiv
Vertiv Liebert GXT4 Series Installation and maintenance instructions
Vertiv
Vertiv Liebert GXT5-6000IRT5UXLN User manual
Vertiv
Vertiv Desktop UPS User manual
Vertiv
Vertiv Liebert ITA2 User manual
Vertiv
Vertiv Liebert ITA2 User manual
Vertiv
Vertiv Liebert Installation and maintenance instructions
Vertiv
Vertiv Liebert GXT RT+ Series Installation and maintenance instructions
Vertiv
Vertiv Liebert NX 225 kVA User manual
Vertiv
Vertiv Liebert GXT5 Installation and maintenance instructions
Vertiv
Vertiv Liebert ITA2 30kVA User manual
Vertiv
Vertiv Liebert NXL User manual
Vertiv
Vertiv Liebert GXT5-750IRT2UXL Installation and maintenance instructions
Vertiv
Vertiv Liebert PSA User manual
Vertiv
Vertiv Liebert Trinergy Cube Instruction Manual
Vertiv
Vertiv Liebert ITA2 Installation and maintenance instructions
Vertiv
Vertiv Liebert NXC 0060kTJ1AFN02000 User manual
Vertiv
Vertiv Liebert GXT5 Installation and maintenance instructions
