Versitron M727xS User manual
A010430357
M727xS
10/100BaseTX-FX
‘Selectable’
Media Converter
InstallationGuide
Copyright January 2004
VERSITRON, Inc.
83 Albe Drive / Suite C
Newark, DE 19702
www.versitron.com
www.versitron.com2
The information contained in this document is subject to change without prior notice. Copyright © All Rights
Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
This device complies with Class B Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
receivedincludingtheinterferencethatitmaycause.
CE NOTICE
Marking by the symbol indicates compliance of this equipment to the EMC directive of the European
Community.Such marking isindicative that thisequipment meets orexceeds the followingtechnical standards:
EMC Class B
EN50081-1/1992: EN55022,EN61000-3-2,EN61000-3-3
EN50082-1/1998: EN61000-4-2,EN61000-4-3, EN61000-4-4,EN61000-4-5, and EN61000-4-6,
EN61000-4-8,EN61000-4-11
www.versitron.com3
Table of Contents
1. Introduction................................................................ 4
1.1 Key Features.............................................................................................4
1.2 Specifications............................................................................................5
1.3 OpticalSpecifications................................................................................9
1.4 SpecialFunctions....................................................................................10
1.4.1 AutoMDI/MDI-XFunction ....................................................................10
1.4.2 Auto-negotiationFunction.......................................................................10
1.4.3 Far End Fault Function............................................................................10
1.4.4 LinkFaultPass-through Function.............................................................11
1.4.5 Remote TP Port Monitoring Function.......................................................12
1.4.6 LoopBackTest Function.........................................................................12
2. Installing the Switch....................................................13
2.1 Unpacking..............................................................................................13
2.2 MountingtheDevice ...............................................................................13
2.3 ApplyingPower......................................................................................14
2.4 Making TP Port Connection ....................................................................15
2.5 MakingFX PortConnection ....................................................................16
2.6 LEDIndicators........................................................................................17
2.7 Performing Loop Back Test.....................................................................18
3. Optional Configuration Settings...................................19
3.1 UserInaccessibleJumpers .......................................................................20
3.1.1 ForwardingModeSetting JP1..................................................................20
3.1.2 802.3x Function Setting JP2.....................................................................21
3.1.3 FXDuplexSetting JP3............................................................................21
3.2 JP1-JP3FactoryDefault Settings..............................................................21
www.versitron.com4
1. Introduction
The 10/100BaseTX-FX media converter series provides a media conversion
allowing high-speed integration of fiber optic and twisted-pair segments. With
10BaseT and 100BaseTX support, the converters provide seamless translation
between Ethernet and Fast Ethernet networks. A complete set of LEDs allows
forquick status verification.
1.1 Key Features
The media converters also provide the following key features:
•Convert speed and media type
•Support full wire speed conversion
•Support 10Mbps and 100Mbps speed on TP connections
•Auto MDI/MDI-X detection function on the TP port
•Auto-negotiation function on the TP port
•Link fault pass-through function
•Provide manual configuration settings for TP port to support connection
to non-auto-negotiation devices
•Transparent to 802.1Q VLAN tagged packets
•Far End Fault function on FX port
•Provide LED status display for remote TP port monitoring
•Provide Loop Back Test function for installation diagnostics
•Support wide range of fiber options on the FX port
•Support media converter center chassis installation
•Support center chassis management
•Provideuser-inaccessible settings for specific system applications
•Low power consumption
www.versitron.com5
1.2 Specifications
Twisted-Pair Interface (TP Port)
Connector Shielded RJ-45
Pin Assignments AutoMDI/MDI-Xdetection
Signal Compliance 802.3 10Base-T, 802.3u 100BaseTX
Data Speed 10Mbps or 100Mbps
Duplex Mode Half-duplex or Full duplex
Configuration Auto-negotiationcapableandoptional
forced manual settings
Cable Types 10Mbps -- Category 3, 4, or 5 UTP
100Mbps – Category 5 UTP
Supported Link Distance Up to 100 meters
www.versitron.com6
Fiber Optic Interface (FX Port)
Signal Compliance 802.3u 100BaseFX
Connector SC, ST, or Single SC
Data Speed 100Mbps
Duplex Mode Full duplex and optional half-duplex
Cable Types Multimode (MMF) - 50/125, 62.5/125µm
Single mode (SMF) - 9/125µm
Supported Link Distance MMF up to 2km
SMF up to 90km
Single SMF WDM up to 20km
Eye Safety compliance IEC825 Class 1
Loop Back Test Button (LOOP TEST)
PUSH Start loop back test
RELEASE Stop loop back test
User Accessible Settings (SW)
NO. SETTING STATE FUNCTION
SW1 TP Port Configuration OFF Auto-negotiation (default)
ON Forced mode
SW2 TP Port Duplex OFF Full duplex (default)
ON Half-duplex
SW3 TP Port Speed OFF 100Mbps (default)
ON 10Mbps
SW4 Link Fault Pass-through OFF Disable (default)
ON Enable
SW5 Reserved
Optional Settings (User inaccessible JP1-JP3 on board)
NO. SETTING STATE FUNCTION
JP1 Forwarding mode Open Store-and-forward (default)
Short Smart-forward mode
JP2 802.3x function Open Enable (default)
Short Disable
JP3 FX port duplex Open Full duplex mode (default)
Short Half-duplex mode
www.versitron.com7
LED Indicators
LED DISPLAY STATE INTERPRETATION
PWR Powerstatus ON Poweron
OFFPoweroff
TP LINK TP port link status ON Link up and no traffic
OFF Link fault
Blink Rx/Tx activities
TP 100M TPport speed status ON 100Mbps
OFF 10Mbps
TP FDX TP port duplex status ON Full duplex
OFF Half-duplex
Blink Collisionsonhalf-duplex
FX LINK FX port link status ON Link up and no traffic
OFF Link fault
Blink Rx/Tx activities
FX OL FX port optical link ON Opticalsignal is detected
OFF No optical signal
RTP LINK Remote TP port link ON Link up and no traffic
OFF Link fault
RTP 100M RemoteTP port speed ON 100Mbps
OFF 10Mbps
RTP FDX RemoteTP port duplex ON Full duplex
OFF Half-duplex
RTP LINK/100M/FDX LEDs are also used for loop back test report.
DC Power Input
DC Input Jack D6.3mm D2.0mm
Operating Input Voltage +4.75V ~ +12.6V
Power Consumption 2W max. (0.27A@+7.5V)
Power Supply Options ExternalAC-DC power adapters
Rated AC120V/60Hz DC7.5V 1A
Rated AC230V/50Hz DC7.5V 1A
Rated AC100V/50-60Hz DC7.5V 1A
Rated AC100V/50-60Hz DC5V 1A
Rated AC240V/50Hz DC7.5V 1A
www.versitron.com8
Center Connector
Connector Futurebus 6x4
Function Center chassis installation
Signal Power inputs
Ground
Management interfaces
Basic Information
Forwarding Throughput Full wire speed at 100M full duplex
10Mbps – 14,880pps at 64-byte packets
100Mbps – 14,880pps at 64-byte packets
Packet Types Transparent and no modification for
- IEEE 802.3 standard packets
- IEEE 802.1Q VLAN tagged packets
Packet Length Up to 1522 bytes at store-and-forward mode
No limit at smart-forward mode 100to100
Flow Control Back-pressure for half-duplex mode
802.3x pause-frame base for full duplex mode
Mechanical
Dimension 0.91H x 2.86W x 4.25D in. (23x72.5x108mm)
Housing Enclosed metal with no fan
Mounting Desktop, Wall mount, Center chassis
Weight 0.47 lbs. (212g)
Environmental
OperatingTemperature -5ºC ~ 40ºC
Storage Temperature -20ºC ~ 85ºC
Relative Humidity 5% ~ 90%
Certificate
FCC Part 15 Class B
CE/EMC EMI EN50081-1 Class B, EMS EN55024
CE/LVD EN 60950
www.versitron.com9
1.3 Optical Specifications
The media converter series provides the following fiber options:
Duplex Fiber Series
Model Connector Fiber Wavelength TxPower Sensitivity Distance
M7273S STDuplex MM 1310nm -19~ -14dBm -33dBm 2 Km
M7274S SC Duplex MM 1310nm -19~ -14dBm -33dBm 2 Km
M7275S-2 SC Duplex SM 1310nm -15~ -8dBm -30dBm 20 Km
M7275S-5 SC Duplex SM 1310nm - 5~ 0dBm -35dBm 50 Km
M7275S-9 SC Duplex SM 1310nm 0~ + 5dBm -37dBm 90 Km
Single Fiber WDM Series
Model Connector Fiber Wavelength TxPower Sensitivity Distance
M7275S-2SFA SC Single FiberSM TX 1310nm -14~ - 8dBm -33dBm 20 Km
RX 1550nm
M7275S-2SFB SC Single Fiber SM TX 1550nm -14~ - 8dBm -33dBm 20 Km
RX 1310nm
www.versitron.com10
1.4 Special Functions
1.4.1 Auto MDI/MDI-X Function
This function allows the TP port to auto-detect the twisted-pair signals and
adapts itself to form a valid MDI to MDI-X connection with the remote
connected device automatically.
1.4.2 Auto-negotiation Function
When the TP port is set on Auto-negotiation mode (SW1:ON), it is featured
with auto-negotiation function and full capability. It performs a negotiation
process for the speed and duplex configuration with the connected device
automatically each time a link is being established.
1.4.3 Far End Fault Function
The FX port is facilitated with this function, which conforms to IEEE 802.3u
100BaseFX specifications. When the FX port detects a link failure on its
receiving circuitry, it will send out an FEFI (Far End Fault Indication) signal to
the remote connected device to indicate a remote fault is detected. It also is
capable of receiving a FEFI signal sent from the remote link partner. Upon
receiving an FEFI signal, it indicates a link failure occurred on the transmitting
path. This function allows the converter to report a fiber link fault even when
a link failure occurred on the transmitting fiber cable.
Table of contents
Other Versitron Media Converter manuals
