Vent-Axia VA150A Assembly instructions

VA150

Window Extract Fan

VA150A / VA150P

Stock Ref.No

VA150A

– 153110B

VA150P

– 152110B

220-240V~50Hz

READ IN CONJUNCTION WITH ILLUSTRATIONS

PLEASE SAVE THESE INSTRUCTIONS

Installation and wiring Instructions

Installation and Wiring Instructions for the VA150 Kitchen A, P Extract Fan.

IMPORTANT:

READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

•This appliance is not suitable for installation in a shower cubical or enclosure and must be sited away from any

source of water spray, and must be out of reach of a person using a fixed bath or shower.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

•Sudden ductwork bends or transformations close to the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E. Regulations, or the appropriate standards of your country

and MUST be installed by a suitably qualified person.

B. The Fan should be provided with a local all pole isolator switch having a contact separation of at least 3mm.

C. Ensure that the mains supply (Voltage, Frequency, and Phase) complies with the rating label.

D. The Fan should only be used in conjunction with the appropriate Vent-Axia products.

E. It is recommended that the connection to the fan connecter terminals is made with flexible cable.

F. When the Fan is used to remove air from a room containing a fuel-burning appliance, ensure that the air

replacement is adequate for both the fan and the fuel-burning appliance.

G. This appliance is not intended for use by young children or infirm persons without supervision.

H. Young children should be supervised to ensure that they do not play with the appliance.

A. INSTALLATION.

WHERE TO FIT

AA short circuit of the airflow should always be avoided by siting the fan as far away as possible from and

opposite to the main source of air replacement.

FAN DIMENSIONS

Bi Before commencing work, the tables in Fig Bi should be read to ensure the fan will fit in the position

proposed.

THICKNESS OF GLASS

C1 Fans can be fitted in most types of glass with a fixing thickness up to 32mm, with the screws provided.

When fixing thickness exceeds 32mm, the unit should be secured with Extended Fixing Rods, available as an

accessory item (56 81 04). If the unit is to be installed in a location exposed to severe wind turbulence thicker

glass will be required – consult with Vent-Axia Technical Support for advice.

136

Suggested Minimum

Glass Thickness

PREPARATION FOR INSTALLATION (Dismantling)

D1 Place the fan unit, external grille downwards, on a flat surface.

D2 Unscrew grille securing screw located at the top of the grille. Remove internal grille.

D3 Slacken the two safety catch screws on the face of the housing. Depress the side catches.

D4 Lift off the housing.

D5 Remove the top cover from its housing. Check rating label to ensure that the fan unit is the correct voltage.

D6 Ease back the motor support safety catch located in the left-hand top corner of the base housing. Rotate

motor support assembly anticlockwise until the bayonet catches disengage from the base housing.

D7 Withdraw motor support assembly and place with the impeller downwards.

D8 Separate the base housing from the external grille assembly.

FITTING

For Dimensions see Bi

Measure the glass thickness and determine the length of fixing screw required (C1).

Glass thickness 4 to 17mm – Break/ cut off ends of screws supplied.

Glass thickness 16 to 32mm – Use screw as supplied.

Glass thickness 32mm and greater – Use extended rods (56 81 04) available as an accessory.

E1 From the inside, place the spigot centrally through the fixing hole with the connector hole upwards.

Ensure the rubber seal is correctly located over lugs and around the spigot.

E2 From the outside, place the exterior grille assembly over the projecting spigot, ensure that the grille

louvers are slanting downwards.

E3 From the inside, insert the four thumbscrews through the holes around the spigot. Finger-tighten the

screws progressively, in turn, to give an even pressure round the hole into the glass.

E4 Locate and replace the motor support assembly and turn clockwise until the safety catch is fully engaged.

WARNING: THE FAN AND ANY ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

REFER TO SECTION B– WIRING. BEFORE CONTINUING WITH RE-ASSEMBLING THE FAN

RE-ASSEMBLE (WINDOW/ WALL)

E5 Replace the housing with the top cover slot uppermost. Feed the pullcord (VA150P) through the slot in the

bottom of the housing. Ensure the arm protruding from the actuator housing is in its lower position, i.e.

shutter closed.

E6 With the two side catches fully engaged, tighten the catch safety screws.

E7 Replace the internal grille. Locate the bottom edge first and then engage the top. Tighten the securing

screw at the top of the grille.

E8 Switch on the mains supply. Check the fans operation.

VA150 P – 1) Pull the pullcord once and release. The shutter will open and the fan will commence extraction.

2) Pull the pullcord again and release. The shutter will close and the fan will stop.

VA150 A – 1) Switch on power supply (switch). The shutter will open and the fan will commence extraction.

2) Switch off power supply (switch). The shutter will close and the fan will stop.

PULLCORD ON

'P' MODEL ONLY

1 Phase Supply

(220-240V 50Hz).

Switched

Fused Spur

FUSE

Fan L N

B. WIRING.

WARNING: THE FAN AND ANY ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

Take the top cover. Make a suitable hole in the grommet. Pass the cable through the hole and slide the

top cover into the base housing.

•VA150A and VA150P fans are Class II double insulated and MUST NOT BE EARTHED

•A Cable Clamp is provided adjacent to the terminal block and must be used.

1) Loosen the cable clamp screws and pass the cable through the clamp.

2) Connect the LIVE (Brown) to the terminal L, and NEUTRAL (Blue) to the terminal N.

3) Tighten the cable clamp screws evenly, ensuring a secure grip on the outer sheath of the cable.

•The Fan should be provided with a local all pole isolator switch. With contact separation of at least 3mm.

C. SERVICING AND MAINTENANCE.

WARNING: THE FAN AND ANY ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED

FROM THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no build

up of dirt or other deposits.

2. Remove the Indoor Grille (See Section D2 for instructions) and wash in warm soapy water.

3. Wipe the shutter blades with a damp cloth until clean.

4. Replace the Grille.

PRODUCT FICHE

For Residential Ventilation Units (Complying Commission Delegated Regulation (EU) No 1254/2014)

Name:

Vent-Axia

Model ID (Stock Ref.) : VA 150 P - 152110 VA 150 A - 153110

SEC Class F F

SEC Value ('Average') 13.97 13.97

SEC Value ('Warm')

6.32

SEC Value ('Cold') 27.32 27.32

Label Required? (Yes/No=Out of scope) No No

Declared as: RVU or NRVU/UVU or BVU RVU-UVU RVU-UVU

Speed Drive

Multi-Speed

Type HRS (Recuperative, Regenerative, None) None None

Thermal Eff: [ (%), NA(if none)] N/A N/A

Max. Flow Rate (m3/h) 216.00 216.00

Max. Power Input (W): (@Max.Flow Rate)

19.00

LWA: Sound Power Level (dB) 54.52 54.52

Ref. Flow Rate (m3/s) 0.04 0.04

Ref. Pressure Diff. (Pa) N/A N/A

SPI [W/(m3/h)]

0.13

Control Factor & Control Typology: (CTRL/ Typology)

Control Factor; CTRL 1.00 1.00

Control Typology Manual Control Manual Control

Declared: -Max Internal & External Leakage Rates(%) for BVUs or carry

over (for regenerative heat exchangers only),

-&Ext. Leakage Rates (%) for Ducted UVUs;

N/A N/A

Mixing Rate of Non-Ducted BVUs not intended to be equipped with

one duct connection on either supply or extract air side; N/A N/A

Position and description of visual filter warning for RVUs intended for

use with filters, including text pointing out the importance of regular

filter changes for performance and energy efficiency of the unit

N/A N/A

For UVUs (Instructions Install Regulated Supply/Extract Grilles Façade) In F&W In F&W

Internet Address (for Disassembly Instructions) www.vent-axia.com www.vent-axia.com

Sensitivity p. Variation@+20/-20 Pa: (for Non-Ducted Vus) N/A N/A

Air Tightness-ID/OD-(m3/h) (for Non-Ducted Vus) N/A N/A

Annual Electricity Consumption: AEC (kWh/a) 1.73 1.73

Annual Heating Saved: AHS (kWh/a)

AHS: Average 13.97 13.97

AHS: Warm 6.32 6.32

AHS: Cold 27.32 27.32

This manual suits for next models

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia Lo-Carbon Silhouette 100HT Assembly instructions

Vent-Axia

Vent-Axia ACH100B Assembly instructions

Vent-Axia

Vent-Axia Sentinel Kinetic B Guide

Vent-Axia

Vent-Axia HR100W User guide

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus SELV Series Assembly instructions

Vent-Axia

Vent-Axia TX7 WL Assembly Instructions

Vent-Axia

Vent-Axia Lo-Carbon Sylph 100CV Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon iQ User manual

Vent-Axia

Vent-Axia Lo-Carbon VA150P Assembly instructions

Vent-Axia

Vent-Axia sentinel Kinetic MVHR series User manual

Vent-Axia

Vent-Axia Lo-Carbon Centra Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon PoziDry Compact Series Assembly instructions

Vent-Axia

Vent-Axia JUPITER315 Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Assembly instructions

Vent-Axia

Vent-Axia NBR DMEV 100 Assembly instructions

Vent-Axia

Vent-Axia 9” DESK FAN Owner's manual

Vent-Axia

Vent-Axia Kinetic Advance White User manual

Vent-Axia

Vent-Axia VASF100B Assembly instructions

Vent-Axia

Vent-Axia NBR DMEVe 100 Assembly instructions

Vent-Axia

Vent-Axia Eclipse 100XP 427281 Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon MULTIVENT MVDC-MS Assembly instructions

Vent-Axia

Vent-Axia MFQ35014 Assembly instructions

Vent-Axia

Vent-Axia Sentinel Operating instructions

Vent-Axia

Vent-Axia Lo-Carbon Square TM Assembly instructions

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual