Vent-Axia VA100 Series Assembly instructions

Installation and Wiring Instructions

Stock Ref. N°

VA100LP 25 11 10B

VA100LT 25 12 10B

VA100XP 25 13 10C

VA100XT 25 14 10C

VA100LHP 25 16 10E

VA100XHP 25 17 10F

VA100XHT 25 15 10C

PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH

ILLUSTRATIONS. PLEASE SAVE THESE INSTRUCTIONS.

VA100

220-240V~50Hz

IP44

Installation and Wiring Instructions for the VA100 Fan.

IMPORTANT:

READ THESE INSTRUCTIONS

BEFORE COMMENCING THE

INSTALLATION

DO NOT install this product in areas where the following may be present or occur:

•Excessive oil or a grease laden atmosphere.

•Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures higher than 40°C or less than –5°C.

• Possible obstructions which would hinder the access or removal of the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E.

Regulations, or the appropriate standards of your country and

MUST be installed by a suitably qualified person.

B. The fan should be provided with a local isolator switch capable

of disconnecting all poles, having a contact separation of at

least 3mm.

C. Ensure that the mains supply (Voltage, Frequency, and Phase)

complies with the rating label.

D. The fan should only be used in conjunction with the

appropriate Vent-Axia products.

E. It is recommended that the connection to the fan connector

terminals is made with flexible cable.

F. When the fan is used to remove air from a room containing a

fuel-burning appliance, ensure that the air replacement is

adequate for both the fan and the fuel-burning appliance.

G. The fan should not be used where it is liable to be subject to

direct water spray for prolonged periods of time.

H. Where ducted fans are used to handle moisture-laden air, a

condensation trap should be fitted. Horizontal ducts should be

arranged to slope slightly downwards away from the fan.

I. This appliance is not intended for use by young children or

infirm persons without supervision.

J. Young children should be supervised to ensure that they do

not play with the appliance.

DESCRIPTION

The VA100 from Vent-Axia is a 100mm extract fan for domestic bathrooms and WC’s

available as window, wall or panel mounted models. Model options with shutter, timer

and auto humidity control.

ACCESSORIES (not supplied)

A range of 100mm wall and window kits are available for

installing into most walls/windows using telescopic

liners/spacers supplied.

A. INSTALLATION

WHERE TO FIT

A short circuit of the airflow should always be avoided by positioning the fan as far

away as possible from and opposite to the main source of air replacement. Fig. 1.

VA100LH, VA100XH and VA100XHT. These models are fitted with automatic

electronic humidity sensing. The humidity sensor needs free air circulation so do not

site close to cupboards, etc. Do not site above a radiator or other heat source.

PANEL/CEILING MOUNTING

IMPORTANT: The fan should be installed into a closed duct system or protected by an

exterior air grille.

1. Cut a 105mm diameter hole in the fixing surface.

2. Remove the grille by loosening the screw at the bottom of the grille.

3. Mark the screw centres through the holes in the fan back plate. Drill, plug and

screw into position.

4. Replace grille and tighten the screw.

WINDOW MOUNTING (Window kit not supplied – see Accessories above)

1. Cut a 105mm diameter hole in the glass.

2. Fit spacers as required behind the fan back plate, engaging the locating pips in

the corner holes.

3. Place the fan spigot through the hole in the glass from the inside, with a gasket

on each side of the glass.

4. From the outside, place on the remaining spacer, with the locating pips facing

outwards. For double-glazing and materials up to 40mm thick, one or more

spacers may be discarded.

5. Draw the assembly together with the threaded fixing ring. Do not over-tighten.

6. Fix the exterior grille in position, using the screws provided, with the louvres

pointing downwards.

White Brown

Window

254101A N/A

Wall 254102 254100

Stock Reference

WALL MOUNTING (Wall kit not supplied – see Accessories above)

1. Cut a 115mm diameter hole through the wall and insert the wall sleeve with the

large diameter sleeve on the room side. Slope the sleeve slightly downwards

away from the fan. Cement both ends into position flush with the wall faces.

2. Remove the grille by loosening the screw at the bottom of the grille.

3. Mark the screw centres on the wall through the holes of the fan back plate. Drill

plug and screw into position.

4. Repeat for the external grille sub-frame. Fix exterior grille into position with the

louvres positioned downwards.

AFTER INSTALLATION ENSURE IMPELLER ROTATES FREELY

WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST

BE ISOLATED FROM THE POWER SUPPLY DURING THE

INSTALLATION / OR MAINTENANCE.

B. WIRING.

IMPORTANT: There are two methods of cable entry to the fan. If the side cable entry

option is used, ensure the supplied grommet is used and maintains a good

seal to prevent water ingress.

The VA100 is suitable for connection to 220-240V/1/50Hz supply. It is class

II double insulated and MUST NOT be earthed.

1. Select and follow the appropriate wiring diagram. (Fig. 2, 3 or 4)

2. Check all connections have been made correctly and ensure all terminal

connections and cable clamps are securely fastened.

3. Ensure the impeller rotates and is free from obstructions.

C. SETUP

TIMER ADJUSTMENT (VA100LT, VA100XT & VA100XHT)

BEFORE ADJUSTING THE TIMER, SWITCH OFF THE MAINS SUPPLY. TIMER

SHOULD ONLY BE ADJUSTED BEFORE OR DURING INSTALLATION.

1. Remove the fan grille. The controller is factory set at 15 minutes approx.

The overrun time period can be adjusted from 3-25 minutes by altering the

adjuster on the control PCB.

2. To REDUCE the operating time, use a small screwdriver to turn the

adjuster ANTI-CLOCKWISE.

3. To INCREASE the operating time, use a small screwdriver to turn the

adjuster CLOCKWISE.

4. Replace the fan grille.

HUMIDITY SET-POINT ADJUSTMENT

BEFORE ADJUSTING THE CONTROLLER, SWITCH OFF THE MAINS SUPPLY.

HUMIDISTAT SHOULD ONLY BE ADJUSTED BEFORE OR DURING

INSTALLATION.

1. Remove the fan grille. The controller is factory set to switch on at about

70% RH. The humidity set point can be adjusted from 40-95%RH by

altering the adjuster on the control PCB.

2. To LOWER the set-point use a small screwdriver to turn the adjuster ANTI-

CLOCKWISE. This makes the controller MORE sensitive.

3. To RAISE the set-point use a small screwdriver to turn the adjuster

CLOCKWISE. This makes the controller LESS sensitive.

4. Replace the fan grille.

IMPORTANT: Upon installation it is possible that the humidity controller will make the

fan run continuously until it has acclimatised to the environment. As part of the

installation process it is important to set/adjust the humidity sensitivity to the desired

position. The controller is already factory set to switch on at about 70% R.H.

SHUTTER OPERATION

The shutter mechanism in all VA100‘X’ model fans will open approximately one minute

after the fan is turned on. The shutter will close about a minute after the fan is switched

off.

PULLCORD OPERATION (VA100LH, VA100XH)

The PULLCORD will activate the fan when switched. When the PULLCORD is

switched into the off position, After which the fan will return to the Auto sensing mode.

The Neon will only activate if the PULLCORD is in the ON position.

NEON OPERATION

The Neon will activate whenever the LS or PULLCORD is activated. The NEON will

switch off if the fan is running in Timer overrun or Humidity mode (if applicable).

D. SERVICING AND MAINTENANCE.

1. At intervals appropriate to the installation, the fan should be inspected and cleaned to

ensure there is no build up of dirt or other deposits.

2. Wipe the inlets and front face with a damp cloth until clean.

The fan has sealed for life bearings, which do not require lubrication.

(220-240V 50Hz).

FUSE

1 AMP

FAN

PULL CORD

SWITCHED FUSED

SPUR (1A)

Fig. 1

Fig. 2 : VA100L

Fig. 3 : VA100X/VA100LH/VA100XH

Fig. 4 : VA100XT/VA100LT/VA100XHT

(VA100LH & VA100XH LS CAN BE USED AS OVERRIDE)





1 PHASE SUPPLY

(220-240V 50Hz).

FUSE

SWITCHED

FUSED

SPUR (1A)

FAN

PULL CORD

1 AMP

~ N

FAN

1 AMP

PRODUCT FICHE

For Residential Ventilation Units (Complying Commission Delegated Regulation (EU) No 1254/2014)

Name: Vent-Axia Vent-Axia Vent-Axia Vent-Axia Vent-Axia Vent-Axia Vent-Axia

Model ID (Stock Ref.) :

VA100LP

51110

VA100LT

51 10

VA100XP

51310

VA100XT

51410

VA100LHP

51610

VA100XHP

51710

VA100XHT

51510

SEC Class F F F F D D D

SEC Value ('Average') 13.97 15.7 13.97 15.7 6. 3 6. 3 6. 3

SEC Value ('Warm') 6.3 7.11 6.3 7.11 11.86 11.86 11.86

SEC Value ('Cold') 7.3 30.75 7.3 30.75 51.31 51.31 51.31

Label Required? (Yes/No=Out of scope) No No No No No No No

Declared as: RVU or NRVU/UVU or BVU RVU-UVU RVU-UVU RVU-UVU RVU-UVU RVU-UVU RVU-UVU RVU-UVU

Speed Drive Multi-Speed Multi-Speed Multi-Speed Multi-Speed Multi-Speed Multi-Speed Multi-Speed

Type HRS (Recuperative, Regener

ative,

None) None None None None None None None

Thermal Eff: [ (%), NA(if none)] N/A N/A N/A N/A N/A N/A N/A

Max. Flow Rate (m3/h) 108.00 108.00 108.00 108.00 108.00 108.00 108.00

Max. Power Input (W): (@Max.Flow Rate) 0.00 0.00 0.00 0.00 0.00 0.00 0.00

LWA: Sound Power Level (dB) 53.5 53.5 53.5 53.5 53.5 53.5 53.5

Ref. Flow Rate (m3/s) 0.0 0.0 0.0 0.0 0.0 0.0 0.0

Ref. Pressure Diff. (Pa) N/A N/A N/A N/A N/A N/A N/A

SPI [W/(m3/h)] 0. 6 0. 6 0. 6 0. 6 0. 6 0. 6 0. 6

Control Facto

r & Control Typology: (CTRL/

Typology)

Control Factor; CTRL 1.00 0.95 1.00 0.95 0.65 0.65 0.65

Control Typology Manual

Control Clock Control Manual

Control Clock Control

Local

Demand

Control

Local

Demand

Control

Local

Demand

Control

Declared: -Max Internal & External Leakage

Rates(%) for BVUs or carry over (for

regenerative heat exchangers only),

-&Ext. Leakage Rates (%) for Ducted UVUs;

N/A N/A N/A N/A N/A N/A N/A

Mixing Rate of Non

Ducted BVUs not

intended to be equipped with one duct

connection on either supply or extract air

side;

N/A N/A N/A N/A N/A N/A N/A

Position and description of visual filter

warning for RVUs intended for use with

filters, including text pointing out the

importance of regular filter changes for

performance and energy efficiency of the

unit

N/A N/A N/A N/A N/A N/A N/A

For UVUs (Instructions Install Regulated

Supply/Extract Grilles Façade) In F&W In F&W In F&W In F&W In F&W In F&W In F&W

Internet Address (for Disassembly

Instructions)

www.vent

axia.com

www.vent

axia.com

www.vent

axia.com

www.vent

axia.com

www.vent

axia.com

www.vent

axia.com

www.vent

axia.com

Sensitivity p. Variation@+ 0/

0 Pa:

(for

Non-Ducted Vus) N/A N/A N/A N/A N/A N/A N/A

Air Tightness

ID/OD

(m3/h) (for Non

Ducted

Vus) N/A N/A N/A N/A N/A N/A N/A

Annual Electricity Consumption: AEC

(kWh/a) 3.65 3.38 3.65 3.38 1.91 1.91 1.91

Annual Heating Saved: AHS (kWh/a)

AHS: Average 13.97 15.7 13.97 15.7 6. 3 6. 3 6. 3

AHS: Warm 6.3 7.11 6.3 7.11 11.86 11.86 11.86

AHS: Cold 7.3 30.75 7.3 30.75 51.31 51.31 51.31

Disposal

This product should not be disposed of with household waste. Please recycle where facilities exist. Check with

your local authority for recycling advice.

Head Office: Fleming Way, Crawley, West Sussex, RH10 9YX. Tel: 01293 526062 Fax: 01293 551188

UK NATIONAL CALL CENTRE, Newton Road, Crawley, West Sussex, RH10 9JA

SALES ENQUIRIES: Tel: 0844 8560590 Fax: 01293 565169

TECHNICAL SUPPORT: Tel: 0344 8560594 Fax: 01293 539209

For details of the warranty and returns procedure please refer to www.vent axia.com or write to Vent Axia Ltd, Fleming Way, Crawley, RH10 9YX

446428

Other manuals for VA100 Series

This manual suits for next models

Table of contents

Other Vent-Axia Fan manuals

Vent-Axia

Vent-Axia TX7WW Assembly Instructions

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Assembly instructions

Vent-Axia

Vent-Axia PUREAIR SENSE User manual

Vent-Axia

Vent-Axia T-Series Assembly Instructions

Vent-Axia

Vent-Axia Lo-Carbon Svelte Series Assembly instructions

Vent-Axia

Vent-Axia MULTIVENT MV250 Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon dMEV Unit T Assembly instructions

Vent-Axia

Vent-Axia VSC Series Assembly instructions

Vent-Axia

Vent-Axia PureAir Home Assembly instructions

Vent-Axia

Vent-Axia MULTIVENT MVDCH Manual instruction

Vent-Axia

Vent-Axia ACQ10012D Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Quadra Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon Revive Series Assembly instructions

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus 427481A Assembly instructions

Vent-Axia

Vent-Axia Serene 8000000042 Assembly instructions

Vent-Axia

Vent-Axia 405215 Advance S Guide

Vent-Axia

Vent-Axia Lo-Carbon Calido Installation instructions

Vent-Axia

Vent-Axia HR300RW6 User guide

Vent-Axia

Vent-Axia sentinel Kinetic MVHR series Guide

Vent-Axia

Vent-Axia T-Series Assembly Instructions

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Series Assembly instructions

Vent-Axia

Vent-Axia PUREAIR SENSE Instruction and safety manual

Vent-Axia

Vent-Axia MVDC-MS Assembly instructions

Vent-Axia

Vent-Axia Solo Series User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual