VEIKOUS PG0202-01 User manual
PG0202-01
Pg.2Pg.1
Pg.2
Pg.3
Pg.4
P1
O
P2
R
P3
T
P4 P5 Q
M6X15 Bolt
Post 1
Big Bolt M6X35 Bolt M6X78 Bolt M6X83 Bolt Nut
Plastic nut cap Plastic M6 bolt cap Ground stake Tool Tool
52 PCS 32 PCS 13 PCS 16 PCS 6 PCS 29 PCS
29 PCS 87 PCS 16 PCS 1 PC 1 PC
2 PCS
Post 2
2 PCS
Post 3
4 PCS
post top cap
4 PCS
Drawstring glidewheel with magnet
1 PC
Middle cross beam
2 PCS
Bottom cross beam 1
2 PCS
Bottom cross beam 2
2 PCS
Side cross beam 1
2 PCS
Side cross beam 2
2 PCS
Enhanced support beam
4 PCS
Triangle cap
14 PCS
post connector
4 PCS
post middle decorative circle
4 PCS
Fabric rib 1
6 PCS
Fabric rib 2
6 PCS
side glidewheel
12 PCS
Bottom cross beam connector
2 PCS
1 2 3 A B C
D D1 E E1 F G
J K L L1 M N
Middel &side cross beam connector
3 PCS
Enhanced support beam connector
2 PCS
Stake piece
4 PCS
Gripping magnet steel piece
1 PC
fabric cover
1 PC
middle glidewheel
5 PCS
N1 N2 U V W Y
Pg.5
Attach post top cap (A) to post (1 & 2)
Attach and fasten stake piece (U) to the
end of post (3) by bolt (P1) and cap (R)
Insert post connector (J) into post (3) by
bolt (P1) and bolt cap (R)
Attach decorative circle (K) to post (3), and attach post (1 & 2) to post (3) by bolt (P1) and bolt cap (R)
Connect two middle cross beams (C) with inside
connector (N1) by bolt (P3) & nut (Q) & nut cap(O)
& bolt cap (R) to make sure that there is no gap
between the two middle cross beams (C) by tighting
the bolts
Assemble 5pcs of middle glidewheels (Y) and drawstring glidewheels with magnet (B) into
middle cross beam (C). Seperate the middle glidewheels (Y) by using bolt (P3) & nut (Q) &
nut cap (O) & bolt cap (R)
Attention: please joint two tubes together without gap and then assemble the screws
Pg.6
Attach triangle cap (G) to assembled
middle cross beam (C)
Assemble six side glidewheels (M) into side cross beam (E),
and then connect side cross beam 1 (E) & side cross beam
2 (E1) with inside connector (N1) by bolt (P3) & nut (Q) &
nut cap(O) & bolt cap (R) to make sue there is no gap
between the two tubes by tighting the bolt
Connect bottom cross beam 1 (D) and bottom cross
beam 2 (D1) with inside connector (N) by bolt (P4) &
nut (Q) & nut cap(O) & bolt cap(R) to make sue there
is no gap between the two tubes by tighting the bolt.
Make sure the bottom cross beam 1 & 2 (D & D1) is
in the same direction
Connect two enhanced support beams (F) with
inside connector (N2) by bolt (P4) & nut (Q) & nut
cap (O) & bolt cap (R) to make sue there is no gap
between the two tubes by tighting the bolt
Attach triangle cap (G) to side cross beam 1 & 2 (E & E1)
Attach triangle cap (G) to assembled bottom cross beam (D & D1)
Pg.7
Attach triangle cap (G) to assembled enhanced support beam (F)
Connect assembled side cross beam ( E1) and
assembled bottom cross beam 2 (D1) to assemled
post (2) by big bolt (P2)
Follow the same step as 14 to connect other three left
Pg.8
Attach assemled middle cross beam (C) to assembled
bottom cross beam (D & D1) by bolt (P5) & bolt cap (R).
Attach gripping magnet steel piece (V) into the middle of
assembled bottom cross beam (D & D1) with bolt (P4) &
nut (Q) & nut cap (O) & bolt cap (R)
Attach assembled enhanced support beam
(F) to assembled bottom cross beam (D &
D1) by bolt (P5)
Insert fabric rib 1 (L) into fabric rib 2 (L1), and
then through assembled fabric rib 1 (L) into
fabric cover (W), and through assembled
fabric rib1 (L) into the hole of glidewheel
(Y&B) which on assembled middle cross
beam (C)
Pg.9
Connect assembled fabric rib 2 (L1) to
the hole of glidewheel (M) which on
assembled side cross beam (E) by
bolt (P1) & bolt cap (R)
Connect drawstring of drawstring glidewheel with
magnet (B) to gripping magnet steel piece (V).
Fix assembled pergola on the ground with
ground stakes (T) if needed.
Other VEIKOUS Tent manuals
