Vaporfi VOLT User manual
USER MANUAL
ENGLISH • ESPAÑOL
VAPORFI™ VOLT TANK
Thanks for your purchase of the VaporFi Volt Tank! In order to use
this tank correctly, effectively and with absolute safety, please follow
the instructions in this manual.
WHAT’S INCLUDED:
» 1 x Volt Tank (4.5ml)
» 1 X OCC Sub Ohm 0.5Ω/ Range 15-30 W
» 1 x OCC 1.2Ω/ Range 12-25 W
» 2 x RBA 0.5ΩCoil
» 1 x Japanese Organic Cotton
» 1 x Mini RBA Base
» 1 x Pyrex Glass Tube
» 1 x Screw Driver
» 2 x Screws
» 1 x User Manual
REFILLING E-LIQUID
1. Turn tank upside down and unscrew the base by turning it
counterclockwise.
2. Point and pour the e-liquid onto the sides of the tank (Do not overfill.
E-liquid should be just below the center tube).
3. Screw the base back onto the tank by turning the base clockwise until
you feel resistance (make sure not to over tighten).
4. Let the tank sit for 1 minute to allow the wick to saturate.
CHANGING THE ATOMIZER HEAD
Atomizers generally last 1-3 weeks depending on
individual usage. When you notice that the flavor
and/or vapor have diminished, you experience a burnt
taste, it may be time to change your atomizer.
1. Remove the tank from the battery and turn the tank
upside down.
2. Unscrew the base of the tank by turning it
counterclockwise.
3. Unscrew the atomizer by turning it counterclockwise.
4. Screw replacement atomizer onto the base by
turning it clockwise.
SWITCH TO REBUILDABLE DECK
1. Remove the base of the tank by turning it
counterclockwise.
2. Unscrew the replaceable atomizer by turning it
counterclockwise.
3. Screw rebuildable deck onto the main base by turning
the deck clockwise.
4. Pint and pour the e-liquid onto the sides of the tank (do
not overfill. Eliquid should be just below the center tube).
5. Screw the base of the tank by turning the base clockwise
until you fell resistance (make sure not to overtighten).
6. Point and pour the e-liquid onto the sides of the tank (Do
not overfill. E-liquid should be just below the center tube).
BUILDING YOUR COIL
Follow these quick and easy steps to build your Volt RBA. Begin by
creating a coil with the provided Kanthal Wire. Here’s how:
1. Cut a piece of Kanthal wire 6” in length.
2. Using the provided screwdriver, hold the screwdriver handle and the
Kanthal wire between your thumb and forefinger.
3. Then tightly wrap the wire around the metal part of the screwdriver.
Wrap the wire 10 times making sure the leads are in opposite
directions and are about 1/2 inch in length.
4. Straighten the leads to mount on the RBA.
5. You should now have a coil.
REBUILDING YOUR ATOMIZER
1. Remove the housing from the Rebuildable Deck.
2. Locate and loosen the post screws on the Rebuildable Deck by
turning it counterclockwise no more than 3 full turns. Make sure the
screws are not removed from the Deck.
3. Attach your coil to the Rebuildable Deck by wrapping the 1/2 inch
leads around the loosened post screws then tighten the screws by
turning clockwise to secure.
4. Cut off all excess wire from the post screws.
5. Cut a strip of the organic cotton about a 1/2 inch in width. Then, roll
tightly the cotton between your thumb and index finger until the
cotton is thin enough to easily slide through the center of the coil.
Table of contents
Other Vaporfi Vaporizer manuals
Vaporfi
Vaporfi VOX 60 TC User manual
Vaporfi
Vaporfi VEX 75 TC User manual
Vaporfi
Vaporfi VOLT 2 User manual
Vaporfi
Vaporfi VOX 80 TC User manual
Vaporfi
Vaporfi VAIO 75 TC User manual
Vaporfi
Vaporfi VAIO 80 TV User manual
Vaporfi
Vaporfi PRO II User manual
Vaporfi
Vaporfi V-GRIP User manual
Vaporfi
Vaporfi V-GRIP 220 User manual
Vaporfi
Vaporfi AIR 2 User manual
