Vanguard VN18A Original instructions

UNVENTED (VENT-FREE) INFRARED GAS HEATER

SAFETY INFORMATION AND INSTALLATION MANUAL

MODELS VN18A, VN18TA, VP16A, VP16TA,

VP26A, VP26TA, VN30A AND VN30TA

Model VN30A Shown

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

www.desatech.com 113052-01F2

SAFETY INFORMATION

WARNING: Improper in-

stallation, adjustment, al-

teration, service or mainte-

nance can cause injury or

property damage. Refer to

this manual for correct in-

stallation and operational

procedures. For assis-

tance or additional infor-

mation consult a qualied

installer, service agency or

the gas supplier.

WARNING: This is an

unvented gas-red heater.

It uses air (oxygen) from the

room in which it is installed.

Provisions for adequate

combustion and ventila-

tion air must be provided.

Refer to Air for Combustion

and Ventilation section on

page 5 of this manual.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects

or other reproductive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble,

operate or service this heater.

Improper use of this heater can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning: Early signs of carbon

monoxide poisoning resemble the u, with head-

aches, dizziness or nausea. If you have these signs,

the heater may not be working properly. Get fresh

air at once! Have heater serviced. Some people

are more affected by carbon monoxide than others.

These include pregnant women, people with heart

or lung disease or anemia, those under the inu-

ence of alcohol and those at high altitudes.

TABLE OF CONTENTS

Safety Information ............................................... 2

Local Codes......................................................... 4

Product Identication........................................... 4

Unpacking............................................................ 4

Product Features ................................................. 4

Air For Combustion and Ventilation..................... 5

Installation ........................................................... 7

Operating Heater ............................................... 14

Inspecting Heater .............................................. 16

Cleaning and Maintenance................................ 17

Troubleshooting................................................. 18

Specications .................................................... 21

Illustrated Parts Breakdown and Parts List........ 22

Replacement Parts ............................................ 26

Service Hints ..................................................... 26

Technical Service............................................... 26

Accessories ....................................................... 26

Service Publications .......................................... 26

Parts Central...................................................... 27

Warranty Information ...........................Back Cover

www.desatech.com 3113052-01F

Natural and Propane/LP Gas: Natural and Propane/

gases are odorless. An odor-making agent is

added to these gases. The odor helps you detect

a gas leak. However, the odor added to the gas

can fade. Gas may be present even though no

odor exists.

Make certain you read and understand all warn-

ings. Keep this manual for reference. It is your

guide to safe and proper operation of this heater.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use a blow-

er insert, heat exchanger insert

or other accessory not approved

for use with this heater.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the heater.

Surface of heater becomes very

hot when running heater. Keep

children and adults away from

hot surface to avoid burns or

clothing ignition. Heater will

remain hot for a time after shut-

down. Allow surface to cool

before touching.

Carefully supervise young chil-

dren when they are in the same

room with heater.

Make sure grill guard is in place

before running heater.

Keep the appliance area clear

and free from combustible ma-

terials, gasoline and other am-

mable vapors and liquids.

1. This appliance is only for use with the type

of gas indicated on the rating plate. This ap-

pliance is not convertible for use with other

gases.

2. Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply

tank(s) outdoors.

3. This heater shall not be installed in a bedroom

or bathroom.

4. If you smell gas

• Shut off gas supply

• Do not try to light any appliance

• Do not touch any electrical switch; do not

use any phone in your building

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions

• If you cannot reach your gas supplier, call

the re department

5. Always run heater with plaque control knob

at the 1, 2, 3 or 4 locked positions. Never

set control knob between locked positions.

Poor combustion and higher levels of carbon

monoxide may result.

6. This heater needs fresh, outside air ventilation

to run properly. This heater has an Oxygen

Depletion Sensing (ODS) safety shutoff

system. The ODS shuts down the heater if

not enough fresh air is available. See Air for

Combustion and Ventilation, page 5.

7. Keep all air openings in front and bottom of

heater clear and free of debris. This will insure

enough air for proper combustion.

8. If heater shuts off, do not relight until you

provide fresh, outside air. If heater keeps

shutting off, have it serviced.

9. Do not run heater

• where ammable liquids or vapors are used

or stored

• under dusty conditions

10. Do not use heater if any part has been under

water. Immediately call a qualied service

technician to inspect the room heater and to

replace any part of the control system and any

gas control which has been under water.

11. Turn off and unplug heater and let cool before

servicing. Only a qualied service person

should service and repair heater.

SAFETY INFORMATION

Continued

www.desatech.com 113052-01F4

12. Operating heater above elevations of 4,500

feet could cause pilot outage.

13. To prevent performance problems, do not use pro-

pane/LP fuel tank of less than 100 lbs. capacity.

14. Before using furniture polish, wax, carpet

cleaner or similar products, turn heater off. If

heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

15.

Provide adequate clearances around air

openings.

LOCAL CODES

Install and use heater with care. Follow all local

codes. In the absence of local codes, use the lat-

est edition of The National Fuel Gas Code, ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

State of Massachusetts: The installation must

be made by a licensed plumber or gas tter in

the Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-red

supplemental room heaters shall provide to

each purchaser a copy of 527 CMR 30 upon

sale of the unit.

Vent-free gas products are prohibited for bed-

room and bathroom installation in the Com-

monwealth of Massachusetts.

SAFETY INFORMATION

Continued

Heater Cabinet

Front Panel

Grill

Guard

Ignitor Button Control

Knob

Plaque

Figure 1 - Vent-Free Gas Heater

PRODUCT

IDENTIFICATION

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging applied to

heater for shipment.

3. Check heater for any shipping damage. If

heater is damaged, promptly return to where

you bought heater.

PRODUCT FEATURES

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS/pilot is a required feature for vent-free room

heaters. The ODS/pilot shuts off the heater if there

is not enough fresh air.

IGNITION SYSTEM

This heater has an electronic ignitor to light heater

fuel supply.

THERMOSTATIC HEAT CONTROL

(Thermostat Models Only)

Thermostat models have a thermostat sensing

bulb and a control valve. This results in the great-

est heater comfort. This can also result in lower

gas bills.

www.desatech.com 5113052-01F

AIR FOR COMBUSTION

AND VENTILATION

WARNING: This heater shall

not be installed in a conned space

or unusually tight construction

unless provisions are provided

for adequate combustion and

ventilation air. Read the following

instructions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

Today’s homes are built more energy efcient

than ever. New materials, increased insulation and

new construction methods help reduce heat loss

in homes. Home owners weather strip and caulk

around windows and doors to keep the cold air out

and the warm air in. During heating months, home

owners want their homes as airtight as possible.

While it is good to make your home energy ef-

cient, your home needs to breathe. Fresh air must

enter your home. All fuel-burning appliances need

fresh air for proper combustion and ventilation.

Exhaust fans, replaces, clothes dryers and fuel

burning appliances draw air from the house to

operate. You must provide adequate fresh air for

these appliances. This will insure proper venting

of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 5 through 7 will help

you classify your space and provide adequate

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows

may provide enough fresh air for combustion and

ventilation. However, in buildings of unusually

tight construction, you must provide additional

fresh air.

Unusually tight construction is dened as con-

struction where:

a. walls and ceilings exposed to the outside

atmosphere have a continuous water vapor

retarder with a rating of one perm (6 x 10-11 kg

per pa-sec-m2) or less with openings gasketed

or sealed and

b. weather stripping has been added on openable

windows and doors and

c. caulking or sealants are applied to areas such

as joints around window and door frames,

between sole plates and floors, between

wall-ceiling joints, between wall panels, at

penetrations for plumbing, electrical and gas

lines and at other openings.

If your home meets all of these three criteria, you

must provide additional fresh air. See Ventilation

Air From Outdoors, page 7.

If your home does not meet all of the three criteria

above, proceed to Determining Fresh-Air Flow

For Heater Location, page 6.

Conned and Unconned Space

The National Fuel Gas Code, ANSI Z223.1/NFPA

54 denes a conned space as a space whose

volume is less than 50 cubic feet per 1,000 Btu

per hour (4.8 m3 per kw) of the aggregate input

rating of all appliances installed in that space and

an unconned space as a space whose volume is

not less than 50 cubic feet per 1,000 Btu per hour

(4.8 m3 per kw) of the aggregate input rating of

all appliances installed in that space. Rooms com-

municating directly with the space in which the

appliances are installed*, through openings not

furnished with doors, are considered a part of the

unconned space.

* Adjoining rooms are communicating only if

there are doorless passageways or ventilation grills

between them.

www.desatech.com 113052-01F6

DETERMINING FRESH-AIR FLOW

FOR HEATER LOCATION

Determining if You Have a Conned or

Unconned Space

Use this work sheet to determine if you have a

conned or unconned space.

Space: Includes the room in which you will install

heater plus any adjoining rooms with doorless pas-

sageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x

width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example: Space size 20 ft. (length) x 16 ft.

(width) x 8 ft. (ceiling height) = 2560 cu. ft.

(volume of space)

If additional ventilation to adjoining room is

supplied with grills or openings, add the volume

of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine

the maximum Btu/Hr the space can support.

__________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 =

51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in

the space.

Vent-free heater ___________ Btu/Hr

Gas water heater* ___________ Btu/Hr

Gas furnace ___________ Btu/Hr

Vented gas heater ___________ Btu/Hr

Gas replace logs ___________ Btu/Hr

Other gas appliances* +__________ Btu/Hr

Total =__________ Btu/Hr

* Do not include direct-vent gas appliances. Di-

rect-vent draws combustion air from the outdoors

and vents to the outdoors.

Example:

Gas water heater ___________ Btu/Hr

Vent-free heater +__________ Btu/Hr

Total =__________ Btu/Hr

4. Compare the maximum Btu/Hr the space can

support with the actual amount of Btu/Hr used.

_________

Btu/Hr (maximum the space can support)

_________

Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space

can support)

60,000 Btu/Hr (actual amount of

Btu/Hr used)

AIR FOR COMBUSTION

AND VENTILATION

Continued

The space in the above example is a conned space

because the actual Btu/Hr used is more than the maxi-

mum Btu/Hr the space can support. You must provide

additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoin-

ing room. If the extra space provides an unconned

space, remove door to adjoining room or add

ventilation grills between rooms. See Ventilation

Air From Inside Building.

B. Vent room directly to the outdoors. See Ventila-

tion Air From Outdoors, page 7.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size

makes room unconned.

If the actual Btu/Hr used is less than the maximum

Btu/Hr the space can support, the space is an un-

conned space. You will need no additional fresh

air ventilation.

WARNING: If the area in

which the heater may be oper-

ated is smaller than that dened

as an unconned space or if the

building is of unusually tight

construction, provide adequate

combustion and ventilation air

by one of the methods described

in the National Fuel Gas Code,

ANSI Z223.1/NFPA54 Section 5.3

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining un-

conned space. When ventilating to an adjoining

unconned space, you must provide two perma-

nent openings: one within 12" of the ceiling and

one within 12" of the oor on the wall connecting

the two spaces (see options 1 and 2, Figure 2,

page 7). You can also remove door into adjoining

room (see option 3, Figure 2, page 7). Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

40,000

20,000

60,000

www.desatech.com 7113052-01F

AIR FOR COMBUSTION

AND VENTILATION

Continued

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or

ducts. You must provide two permanent openings:

one within 12" of the ceiling and one within 12"

of the oor. Connect these items directly to the

outdoors or spaces open to the outdoors. These

spaces include attics and crawl spaces. Follow the

National Fuel Gas Code, ANSI Z223.1/NFPA 54,

Section 5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet

or outlet air into attic if attic has a thermostat-

controlled power vent. Heated air entering the attic

will activate the power vent.

Figure 2 - Ventilation Air from Inside

Building

Figure 3 - Ventilation Air from Outdoors

INSTALLATION

NOTICE: This heater is intended

for use as supplemental heat. Use

this heater along with your primary

heating system. Do not install this

heater as your primary heat source.

If you have a central heating system,

you may run system’s circulating

blower while using heater. This will

help circulate the heat throughout

the house. In the event of a power

outage, you can use this heater as

your primary heat source.

WARNING: A qualied ser-

vice person must install heater.

Follow all local codes.

CHECK GAS TYPE

Use only the correct type of gas (natural or pro-

pane/LP). If your gas supply is not the correct gas

type, do not install heater. Call dealer where you

bought heater for proper type heater.

This appliance is only for use with

the type of gas indicated on the rat-

ing plate. This appliance is not con-

vertible for use with other gases.

WARNING: This appliance

is equipped for (natural or pro-

pane/LP) gas. Field conversion

is not permitted.

INSTALLATION ITEMS

Before installing heater, make sure you have the

items listed below.

• for propane/LP gas, external regulator (supplied

by installer)

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• sediment trap

• tee joint

• pipe wrench

• for natural gas, test gauge connection*

* A CSA design-certied equipment shutoff valve

with 1/8" NPT tap is an acceptable alternative to

test gauge connection. The optional CSA design-

certied equipment shutoff valve can be purchased

from your dealer. See Accessories, page 26.

Outlet

Air

Ventilated

Attic

Outlet

Inlet

Air

Inlet Air Ventilated

Crawl Space

Crawl

Space

To Attic

Remove

Door into

Adjoining

Room,

Option 3

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Ventilation

Grills into

Adjoining

Room,

Option 1

www.desatech.com 113052-01F8

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as, but

not limited to, tobacco smoke,

aromatic candles, cleaning u-

ids, oil or kerosene lamps, etc.) in

the air exist, may discolor walls

or cause odors.

IMPORTANT: Vent-free heaters add moisture

to the air. Although this is benecial, installing

heater in rooms without enough ventilation air may

cause mildew to form from too much moisture.

See Air for Combustion and Ventilation, page

5. If high humidity is experienced, a dehumidi-

er may be used to help lower the water vapor

content in the air.

For convenience and efciency, install heater

• where there is easy access for operation, inspec-

tion and service

• in coldest part of room

An optional fan kit is available from your dealer.

See Accessories, page 26. If planning to use fan,

locate heater near an electrical outlet.

THERMOSTAT SENSING BULB

(Thermostat Models Only)

The thermostat sensing bulb has been placed

below the heater.

1. Place clamp on thermostat sensing bulb as

shown in Figure 5. Clamp is provided in

hardware package.

2. Snap clamp into upper mounting hole as shown

in Figure 5. Mounting hole is located on lower

left edge on back of heater. Make sure the

thermostat sensing bulb is pointing up.

INSTALLATION

Continued

Figure 5 - Attaching Thermostat Sensing

Bulb

Clamp

Thermostat

Sensing

Bulb

LOCATING HEATER

WARNING: Maintain the

minimum clearances shown

in Figure 4. If you can, provide

greater clearances from oor,

ceiling and joining wall.

You can locate heater on the oor, away from a

wall. A wall mounting bracket and oor base stand

are included with this heater. Determine which

method is best for your application.

WARNING: Never install the

heater

• in a bedroom or bathroom

• in a recreational vehicle

• wherecurtains,furniture,cloth-

ing or other ammable objects

arelessthan36"from thefront,

top or sides of the heater

• as a replace insert

• in high trafc areas

• in windy or drafty areas

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must

be at least 18" above oor

• locate heater where moving

vehicle will not hit it

Figure 4 - Mounting Clearances As

Viewed From Front of Heater

Minimum

From

Sides Of

Heater

36"

FLOOR

CEILING

Minimum

Minimum To

Top Surface

Of Carpeting,

Tile Or Other

Combustible

Material

Left

Side

Right

Side

10"

www.desatech.com 9113052-01F

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket in heater carton. Remove

mounting bracket from heater carton.

Figure 6 - Mounting Bracket

INSTALLATION

Continued

Removing Front Panel Of Heater

1. Remove the four painted screws, two on each

side of front panel.

2. Pull bottom of front panel forward, then out.

3. Remove any remaining packaging materials.

Figure 7 - Removing Front Panel Of

Heater

Screw

Front Panel

Marking Screw Locations

1. Tape mounting bracket to wall where heater

will be located. Make sure mounting bracket

is level.

WARNING: Maintain mini-

mum clearances shown in Figure

8. If you can, provide greater

clearances from oor and join-

ing wall.

2. Mark screw locations on wall (see Figure 8).

Note: Only mark last hole on each end of

mounting bracket. Insert mounting screws

through these holes only.

3. Remove tape and mounting bracket from wall.

4 and 5 Plaque Heaters

3 Plaque Heater

Figure 8 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws and spacers

are in hardware package. The hardware package

is provided with heater.

16"

Min.

14"

12"

Min.

Adjoining Wall

14"

Adjoining Wall

Only Insert Mounting

Screws Through Last

Hole On Each End

Only Insert Mounting

Screws Through Last

Hole On Each End

Floor Floor

25 3/4"

Optional

19 3/4"

Min.

25 3/4"

Optional

19 3/4"

Min.

16"

Min.

14"

12"

Min.

Adjoining Wall

14"

Adjoining Wall

Only Insert Mounting

Screws Through Last

Hole On Each End

Only Insert Mounting

Screws Through Last

Hole On Each End

Floor Floor

Optional

Min.

Optional

Min.

Methods For Attaching Mounting Bracket

To Wall

Only use last hole on each end of mounting bracket

to attach bracket to wall. These two holes are 14"

apart from their centers. Attach mounting bracket

to wall in one of two ways:

1. Attaching to wall stud

2. Attaching to wall anchor

Attaching to Wall Stud: This method provides the

strongest hold. Insert mounting screws through

mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you

to attach mounting bracket to hollow walls (wall

areas between studs) or to solid walls (concrete

or masonry).

Decide which method better suits your needs.

Either method will provide a secure hold for the

mounting bracket.

www.desatech.com 113052-01F10

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1. Drill holes at marked locations using 9/64"

drill bit.

2. Place mounting bracket onto wall. Line up last

hole on each end of bracket with holes drilled

in wall.

3. Insert mounting screws through bracket and

into wall studs.

4. Tighten screws until mounting bracket is

rmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls

(wall areas between studs) or solid walls (concrete

or masonry)

1. Drill holes at marked locations using 5/16"

drill bit. For solid walls (concrete or masonry),

drill at least 1" deep.

2. Fold wall anchor as shown in Figure 9.

3. Insert wall anchor (wings rst) into hole. Tap

anchor ush to wall.

4. For thin walls (1/2" or less), insert red key

into wall anchor. Push red key to “pop” open

anchor wings. IMPORTANT: Do not hammer

key! For thick walls (over 1/2" thick) or solid

walls, do not pop open wings.

5. Place mounting bracket onto wall. Line up

last hole on each end of bracket with wall

anchors.

6. Insert mounting screws through bracket and

into wall anchors.

7. Tighten screws until mounting bracket is

rmly fastened to wall.

INSTALLATION

Continued

Figure 9 - Folding

Anchor

Figure 10 - Popping

Open Anchor Wings

For Thin Walls

Figure 11 - Mounting Heater Onto

Mounting Bracket

Mounting

Bracket

(attached

to wall)

Horizontal Slots

Stand-Out Tab

Placing Heater On Mounting Bracket

1. Locate two horizontal slots on back panel of

heater.

2. Place heater onto mounting bracket. Slide

horizontal slots onto stand-out tabs on mount-

ing bracket.

Installing Bottom Mounting Screws

1. Locate two bottom mounting holes. These

holes are near bottom on back panel of heater

(see Figure 12).

2. Mark screw locations on wall.

3. Remove heater from mounting bracket.

4. If installing bottom mounting screws into

hollow or solid wall, install wall anchors.

Follow steps 1 through 4 under Attaching To

Wall Anchor Method.

If installing bottom mounting screw into wall

stud, drill holes at marked locations using 9/64"

drill bit.

5. Replace heater onto mounting bracket.

6. Place spacers between bottom mounting holes

and wall anchor or drilled hole.

7. Hold spacer in place with one hand. With other

hand, insert mounting screw through bottom

mounting hole and spacer. Place tip of screw

in opening of wall anchor or drilled hole.

8. Tighten both screws until heater is rmly

secured to wall. Do not over tighten.

Note: Do not replace front panel at this time.

Replace front panel after making gas connec-

tions and checking for leaks (see page 11).

Figure 12 - Installing Bottom Mounting

Screws

Side View

Front View

Wall

Spacer

Heater

This manual suits for next models

Table of contents

Other Vanguard Gas Heater manuals

Vanguard

Vanguard FLAME-MAX Vintage Oak 18" Quick start guide

Vanguard

Vanguard Flame-Max VYS18PWA Specification sheet

Vanguard

Vanguard FLAME-MAX User manual

Vanguard

Vanguard Flame-Max Vintage Oak Log Design Quick start guide

Vanguard

Vanguard VGN30 Quick start guide

Vanguard

Vanguard VYS18NWA User manual

Vanguard

Vanguard VN12 Quick start guide

Vanguard

Vanguard VS24PR Quick start guide

Vanguard

Vanguard VN1800E Quick start guide

Vanguard

Vanguard VN1800 Quick start guide

Vanguard

Vanguard MINI-HEARTH VMH2800TPC Operation manual

Vanguard

Vanguard SVYD18N Series Quick start guide

Vanguard

Vanguard VMH3000TNA Quick start guide

Vanguard

Vanguard MINI-HEARTH VMH3000TNS Quick start guide

Vanguard

Vanguard VMH3000TN Quick start guide

Vanguard

Vanguard Firewerks VFRMV18NB Quick start guide

Vanguard

Vanguard VP1600ITB Quick start guide

Vanguard

Vanguard VN12A Quick start guide

Vanguard

Vanguard VYD18NRB User manual

Vanguard

Vanguard VN18 Original instructions

Vanguard

Vanguard VMH3000TPSA Quick start guide

Vanguard

Vanguard VP11 Quick start guide

Vanguard

Vanguard UNVENTED (VENT-FREE) NATURAL GAS LOG HEATER Specification sheet

Vanguard

Vanguard kv1500a Service manual

Popular Gas Heater manuals by other brands

Superior

Superior BGE18NV Installation and operation instructions

Dru

Dru Room-sealed atmospheric gas-fired heating... user manual

klover

klover TKR 35 user guide

Rothenberger Industrial

Rothenberger Industrial 035984 instruction manual

New Buck Corporation

New Buck Corporation 34 user manual

Hargrove

Hargrove Timberland Glow Operation and installation guide

Kinder

Kinder Cameo BF Installation and maintenance instructions

Qlima

Qlima GH 438 B-2 Directions for use

Desa

Desa 125-R owner's manual

Gasmate

Gasmate AH100 Series instructions

Medallion

Medallion MBP20TLB OWNER'S OPERATION AND INSTALLATION MANUAL

Clarke

Clarke DEVIL 910SS User instructions

Superior

Superior BGE18NR Operation instructions

Brant Radiant Heaters

Brant Radiant Heaters QTD Series User instruction

L.B. White

L.B. White Therma Grow HW220 Owner's manual and instructions

Sealey

Sealey LP35.V5 instructions

Italkero

Italkero Falo Evo User manual and assembly instructions

Desa

Desa 30LP owner's manual