V-tech IS7121 User manual
1
Installation guide
(Canada version)
IS7121/IS7121-2/IS7121-22
DECT 6.0 cordless telephone
with wireless doorbell
Before using this product, read this Installation guide for
instructions for installing the telephone base, handset and
doorbell. For basic settings and operation instructions, see
the provided Abridged user’s manual.
Basic steps to install your phone and doorbell
5
Doorbell installation
Doorbell location testing
Basic installation
Install telephone base & charger
Install handset battery
Install wall mount bracket
3
2
1
4Install doorbell battery
6Install the doorbell wall mount cover
7Install the doorbell
2
1Install telephone base & charger
Plug!
Click!
Plug!
DSL lter
Click!
Plug!
If you subscribe to telephone service from a cable
company or a VoIP service provider, contact your
cable/VoIP service provider for more information.
3
2Install handset battery
Battery Pack
BT164392/BT264392
2.4V 550mAh Ni-MH
WARNING : DO NOT BURN OR
PUNCTURE BATTERIES
Made in China CR1222
12
3 4
Charge for at least 30 minutes
before initial settings.
Charge for 13 hours before
initial use.
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDEUP / CE CÔTÉ VERS LEHAUT
CR1232
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDEUP / CE CÔTÉ VERS LEHAUT
CR1232
Plug!
Light on!
4
3Install wall mount bracket (optional)
1
2
3
4
Unplug!
Unplug!
Plug!
Slide the bracket down!
Slide the base down!
Click!
5
4Install doorbell battery
BASIC INSTALLATION COMPLETED!
Keep reading for doorbell location testing.
The doorbell can also be supported by AC power. See pages 11 and 12 on how to
install the power adapter.
•
5Doorbell location testing
Before mounting the doorbell on a wall, make sure you test if
the location you install the doorbell is in range, and adjust the
camera angle to best suit your needs.
To test the location for installation:
Hold the doorbell in the location where you want to install the
doorbell, then follow the steps below to test the reception range
and video capture angle.
Press MENU >> Press qor pto Settings >> Press
SELECT.
Press qor pto Doorbell setup >> Press SELECT.
Press /DOORBELL to check the video streaming quality.
The handset displays The handset is muted during the
setup mode, then press OK.
Press , then press +or -to adjust the video streaming
brightness.
If audio feedback occurs, press on the handset to turn off
the speakerphone.
If the desired location is in good range, the handset
displays .
If the desired location is not in good range, the handset
ashes in red. Press INFO for instructions to relocate
your handset and/or telephone base. When the reception
is in good range, the handset displays . Press OK to
return to the video streaming.
6. Keep the video streaming on for camera lens adjustment.
1.
2.
3.
4.
5.
•
•
•
6
18
inches
50 degrees
63 inches
20
inches
Shooting area
Avoid mounting it to where it is exposed to direct sunlight.
Avoid mounting it to where reections may be caused by
sunlight, for example, opposite to a white wall.
Avoid placing other cordless devices near the doorbell.
They may cause interference.
Two built-in infrared LEDs are for night vision. Make sure the
surrounding light source is sufcient for infrared operation.
Test at the front door to determine when the infrared LEDs
turn on. When they are in operation, they turn red.
•
•
•
•
When you check for the desirable location to install the doorbell:
Make sure the visitor is standing in a reasonable distance
away from the doorbell.
•
Infrared LEDs
7
To adjust the shooting area, you may either relocate the doorbell
in different height level, or adjust the camera angle (see below).
To adjust the camera angle:
Tilt the lever to adjust the angle of the camera lens. The
camera lens can be adjusted to left, right or down, up to
10 degrees.
After you have tested the reception range and found the
desirable location to install the doorbell, press END on the
handset to end the video streaming and proceed to Step 6.
•
View
Right
Angle
Adjustment
View
Left
CAUTION
View
Right
Angle
Adjustment
View
Left
CAUTION
DOORBELL LOCATION TESTING COMPLETED!
Keep reading for Install the doorbell wall mount
cover and Install the doorbell.
8
6Install the doorbell wall mount cover
Make sure you have done Doorbell location testing
above before you mount the doorbell on the wall.
There are two ways to position the wall mount cover and
manage the power adapter cord.
Option 1: Install the doorbell wall mount cover without the
wall mount plate
If you drill the holes into a
stud, go to Step 3.
-OR-
If you drill the holes into the
wall, insert the wall anchors
into the holes.
2.Use the two holes on the
doorbell wall mount cover
to mark the exact location
of the screw holes on the
wall.
1.
Align the holes on the
wall mount cover with the
holes on the wall. Tighten
the screws into the holes
to secure the wall mount
cover onto the wall.
3.
Align
Use a sharp object to open
a hole on the soft plastic part
on the doorbell wall mount
cover, then route the power
adapter cord through the
hole.
4.
Open a
hole here
9
Option 2: Install the doorbell wall mount cover with the wall
mount plate
Use the two holes on the
doorbell wall mount cover
to mark the exact location
of the screw holes on the
wall.
Mark an extra mark for
routing the power cord
through the wall.
1.
An extra
mark
Stick the double-sided
adhesive tapes onto the wall
mount plate as specied.
2.
Align and place the wall
mount cover onto the wall
mount plate. Make sure the
sign is pointing upward.
3.
Stick
here
If you drill the holes into a
stud, go to Step 5.
-OR-
If you drill the holes into the
wall, insert the wall anchors
into the holes.
4.
10
Align the holes on the wall mount
cover with the holes on the wall.
Tighten the screws into the holes
to secure the wall mount cover
onto the wall.
6.
Use a sharp object to open a hole on
the soft plastic part on the doorbell
wall mount cover. Route the power
adapter cord through the hole on
the wall and the opening of the wall
mount plate. Then, slide it in through
the hole of the wall mount cover.
5.
Open a
hole here
Other manuals for IS7121
3
This manual suits for next models
2
Table of contents
Other V-tech Cordless Telephone manuals
V-tech
V-tech DS3101 User manual
V-tech
V-tech ES1810A User manual
V-tech
V-tech DS6161 User manual
V-tech
V-tech DS667V-2F User manual
V-tech
V-tech 9116 User manual
V-tech
V-tech 2468 - VT Cordless Phone User manual
V-tech
V-tech 2101 User manual
V-tech
V-tech mi6877 User guide
V-tech
V-tech 2498 - VT Cordless Phone User manual
V-tech
V-tech vt2467 User manual
V-tech
V-tech DS6673-2 User manual
V-tech
V-tech CS6114-11 User manual
V-tech
V-tech IS7256-3 User manual
V-tech
V-tech IA5854 User manual
V-tech
V-tech DDA200BT User manual
V-tech
V-tech LS6115-2 User manual
V-tech
V-tech VT9041 User manual
V-tech
V-tech CS6120-2 User manual
V-tech
V-tech CS6120-2 User manual
V-tech
V-tech GiGA5.8x VT5836 User manual
