V-Show PS200P User manual

200W 成像灯(专业版）

200W LED Profile Spotlight

（Professional Version）

PS200P

Instruction manual

使用说明书

Advice before use

Read these instruction carefully.As soon as the equipment is delivered, Open packing and inspect

the equipment Carefully.

If you notice any damage,immediately contact the transport company and register your

Complaint in due form listing the defects.

Be sure thatthis equipment left our factouy in perfect condition.

Check if the received equipment is consistent with the delivery notice and if this deliver notice is

consistent with your order.If it is not ,immediately contact with you supplier.

General Remarks

his luminaire is lighting equipment designed for professional use only indoors in theatre nd

televison or film studios.It must imperatively be connected to earth by means of its earth wire.

orevent any electrical shock, this equipment should not be opened when functioning.

Nevertheless:

part or lenses have to be replaced if they are visibly damaged and their efficiency ht be reduced,

for example in case of deep cracks or scratches.The lamp must be ged if damaged or distorted by

heat.If internal access is needed for control, service c repair purposes always refer to qualified

personnel.

In all events, always unplug the power supply cable before opening.

It is the user's responsibility to use the luminaire for its intended purpose and to check the

euipment that mignt be connected to it.

luminaire is a piece of professional equipment designed for easy and simple use Nevertheless,

always refer to qualified personnel for any installation or repare work.

Important Remark

Power supply cables and other connections are essential for your equipment and contribute

greatly to a safe and trouble free operation.

Always hold the plug when disconnectiong a cable, never pull the cable.Never use cables

nnectors in bad condition, check them before installation and periodically thereafter.Never tie

power supply and data cables together

Electrical Connection

minaire is designed for operating at a nominal voltage of 230V.It is fitted with a 1.2msilicone

power supply cable（3*1.5mm²）

ur own safety,make sure the earth wire(yellow-green)is ALWAYS connected to earth.

ATTENTION:

LETHAL VILTAGE PRESENT INSIDE

提示

使用前请仔细阅读此安全规则。

该设备已经通过运输到过使用目的地后，请小心打开包装并取出设备如发现任何

缺损，应立即联系货运公司并按照缺损情况进行投诉。确认此设备在出厂时为完

好无损。

请检查接收的设备是否与货运单中登记的货物相符，以及货运单中登记货物与

您的订购的货物相符，如有不符请立即联系您的供货商。

总述

此灯具专为剧场、电视电影工作间等设计的专业户内照明设备。必须将标记为地

级的电线接地线。

不要在此设备运行时打开外壳，以避免被电击。

在镜片发现明显缺损，应立即更换镜片并降低其功率，比如深刻的裂痕或刮痕。

发光体在高热后出现损坏或扭曲变形应立即更换。需要在灯具内部进行检查、维

护、修理等操作时，都应交由专业人士。

一旦出现事故，在打开灯具外壳前应首先拔去电源线插头。

使用者应在此设备规定用途范围内进行操作，并核对设备的线路是否正确连接。

请不要将该灯具置于多变的恶劣环境。

生产商概不承担由于擅自更换其它类型光源而引起的损坏事故责任。

此灯具是一种专业设备，虽设计改良后的操作简单方便，但仍需要专业人士进行

安装维护。

要点

电源线及其它连接装置对于设备都是很重要的，因其合理安排才导致设备的安全

便利运用。

在拔插电源时必须用手持插头并拉出，切勿直接拉扯电源线。

勿在恶劣的环境下使用电源线，在安装前应检测，并在安装后保持周期性的检测

切勿将电源线及其他信号线扎在一起，以防混淆。

电源连接

此灯具适应 230V 的常规电压。并带有 1.2M 硅胶线（1.5 平方）。为了使用者的

安全，务必保持地线（黄绿色）接地。

警告∶

内部带危险电压!

Overview 部件名称

1. Color Chip frame Fixer 1.色片卡槽

2.Color Flake Calipers 2.色片扣

3.Profile lens tube 3.脚部

4.Focusing slot 4.调焦槽

5. Nut for Front Drawtube 5.梅花螺丝

6.Design Adjustment Tube 6.中部

7.Slot for lris 7.缩光圈卡槽

8.Lighting Adjustment Flake 8.切光片

9.Screw for Design Adjustment Tube 9.四星螺丝

10.Light emitting part 10.主体

11.Handle 11.提手

12.Cooperate with the activity slot 12.配合件活动槽

13.Nut for Suspension Loop 13.合金螺丝

14.Handle fit piece 14.提手配合件

15. Slot for Gobo Holder 15.图案片卡槽

Body package specification 灯具包装明细

Number/序号

Description/名称

Units/单位

Quantity/数量

Light

灯具

PCS

Power coed

电源线

PCS

Signal cords

信号线

PCS

nstruction manual

说明书

PCS

Purchased separately options 灯体配件另选项

Number/序号

Description/名称

Units/单位

Quantity/数量

LOGO clamp

图案夹

PCS

Shrink aperture

缩光圈

PCS

Lights hook

灯沟

PCS

Safely cable

保险绳

PCS

The 200W imaging light is a professional imaging light that uses a high-density integrated new light

source, which can fully match the professional 19°, 26°, 36°, 50° lens barrel, and the spot and LOGO

image are clear.

3000K color rendering index 95. Specialized in imaging lights for theaters, theaters, TV stations, studios,

and banquet halls.

200W 成像灯是一款采用高密度集成新型光源的专业成像灯，可完全匹配专业的

19°，26°，36°，50°的镜筒，光斑，LOGO 成像都清晰。

3000K 显色指数 95.专业为剧场，剧院，电视台，演播厅，宴会厅而设的成像灯。

Use &Operation 使用和操作

Adjusting 调整

Draw out 4Lighting Adjustment Flakes⑧,connect the power supply,until the light sots are the brightest,l

oosen the Nut for the Front Drawtube⑤,adjust the Front Drawtube③fore and aft until the margin of the

light spots are the cleraest.

打开 4 件切光片⑧，连接电源，直到最亮的光点，松开螺母的伸缩管⑤，调整前

伸缩管③从头到尾，直到光效最佳为止。

Design Flake 图案片

wanting to get the effect of the design.you must firstly make the designtflake snow erse images.Loosen t

he nut for the Design Flake Fixed Slot 15&then move it forwar the Design Bayonet comes.Out & then in

sert the design flake.Tum on the light,adjus the Front Drawtube③until getting the clearest design,the fa

sten the Front Drawtube.

如果想要得到图案的效果，首先必须使图案片的反图像。松开螺母图案片卡槽

15，然后它向前移动，直到可放入图案夹。取出并插入图案片。不清楚的光，前

后调整脚部位置③，直到获得最清晰的图案，固定好脚部位置。

Color Flake 色片夹

If wanting colors,please clip the color flake with the color flake clip,open the Color Flake Calipers & then

insert the color flake.

如果想要其他颜色，打开色片扣取出色片夹网，把颜色片放入色片夹网夹紧，然

后插入色片卡槽内，关上色片扣

Dimensions 尺寸图

Specifications 规格参数

额定功率 Voltage: AC100-230V 50-60HZ

光源 light source： 200W Edison LED

色温 CT： 3200K/5600K

显指 RA： 95

透镜角度 Lens angle： 19°/26°/ 36°50°（Conventional 19

degrees 常规 19°）

通道 Channel: 2CH

控制模式 Control mode： DMX512 Master-slave

调光 Dimming: linear dimming 线性调光

最高环境温度 Maximum ambient temperature：＜40°

最高表面温度 Maximum surface temperature：＜85°

N.W 净重： 9.5KG

Lighting size 灯具尺寸： 61x32x17.5CM

Menu operation instructions 菜单操作说明

Instructions: according to the function keys A cycle of different function, press B or Ccan modify the para

meter values. Press the D key to confirm.

操作说明∶按功能键 A 会循环出不同的功能，按 B 或 C 键即可修改其参数值。按 D 键确认即

可。

Key operation instructions 按键操作说明

序号

number

菜单 NUME

菜单功能 Menu function

说明 Description

DMX-ADDR

001

DMX512 地址码设置

001/DMX512 address code setting

001

按上下键调节地址码，按确定键

保存/Press the up and down

keys to adjust the address

code, and press the OK key to

save.

R-DIMMER

001

LED 亮度调节

255/LED Dimmer255

按上下键调节 LED 亮度，按确定

键保存/Press the up and down

keys to adjust the brightness

of the LED, and press the OK

key to save.

P_STROBE

255

频闪快慢调节

255/Strobe speed adjustment

255

按上下键调节频闪速度，按确定

键保存/Press the up and down

keys to adjust the strobe

speed, press the OK key to

save

DMX-KEEP

ON/OFF

DMX 信号保持选择/DMX signal keep

selection

按上下键选择是否保持，按确定

键保存/Press the up and down

keys to choose whether to

keep, press the OK key to

The DMX512 Channel 通道说明

Channel

通道

Function/功能

Introduction 说明

1CH

Dimmer/调光

0-255 LED Dimmer Linear dimming from dark to bright 0-255

LED 调光线性调光由暗到量

2CH

Strobe/频闪

0-255 Stroboscopic speed adjustment

0-255 调节频闪速度

address code state, multimachine connection, without control table, which can realize the master-slave

online features, operation of a device, the rest in address d001 state of the host device synchronized wit

h the running program. Through to control if receives the control table, behind the podium display X bec

ome V, the address in the state of equipment can be controlled to control

在地址码状态，多机连接后，若没有接控台，可实现主从联机功能，操作其中的一台设备，

其余的在地址 d001 状态下的设备跟随主机同步运行程序。接通控台后若接收到控台信号，

显示屏的的 X 会变成 V，在地址状态下的设备可受控台控制。

DMX connection DMX 连接

DMX512 is widely used in lamp control, and can control up to 512 channels

On the last luminaire, a terminator is required for the DMX signal line. Solder a 120Ω,

1/4W resistor between pin2 and pin3, install it into the 3-pin XLR plug and plug it into the

DMX output port of the last lamp.

Use the XLR signal cable to connect the lamp, one end to the output port of the lamp, and

the other end to the output port of the next lamp. The XLR signal cable can only be used in

series, not parallel. DMX512 signal transmission speed is very fast. Damage to the signal

line, weak welding, poor contact, etc., will affect signal transmission and cause the system

to shut down.

When the power supply of a certain lamp is cut off, the connection of DMX output and

input is bypassed, so that the connection of DMX line can be maintained.

Each lamp needs an address code, which can receive the information sent by the console,

ranging from 0 to 512. The terminal of the system needs to be equipped with a terminator

to reduce signal transmission errors.

DMX address code setting

When using a universal DMX console to control a lamp, please set the start address code

save

Now temp

灯珠温度/Lamp bead temperature

实测灯珠的当前温度/Measure

the current temperature of the

lamp beads

Other V-Show Spotlight manuals

V-Show

V-Show FSP300 User manual

Popular Spotlight manuals by other brands

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 user manual

LIVARNO home

LIVARNO home 375304 2101 Installation, operating and safety information

Cameo

Cameo CLQS40WW user manual

Leviton

Leviton Ellipsoid 5/50 user guide

Monacor

Monacor img Stage Line PARL-56PDX/CR instruction manual

Vector

Vector SL3AKV instruction manual

Quantum

Quantum Q262 Product data sheet

Philips

Philips Vari-lite VL3015LT user manual

EUROSPOT

EUROSPOT C51 instruction manual

DTS

DTS MINI BRICK ARC user manual

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Installation, operation and maintenance instructions

ACME

ACME LED-MS350B user manual

EuroLite

EuroLite Akku flat light 1 user manual

Commercial Electric

Commercial Electric SPTM-1401 Use and care guide

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Instructions for use

Teknik

Teknik FLEXI user manual

Craftsman

Craftsman CMXLSB10 instruction manual

EuroLite

EuroLite LED SLS-144 UV Floor Spot user manual