URCERI SND133 User manual
Cordless Rechargeable Screwdriver
User Manual
SND133
CONTENTS
English···························1-6
Deutsch························7-12
Français······················13-18
Español······················25-30
Italiano·······················19-24
日本語························31-36
Thank you for choosing Urceri.
Please read the manual carefully before use.
PRODUCT OVERVIEW
EN-1
SND133
Hexagon Chuck
Knurled collar
Torque adjustment collar
LED light
Indicator lights
Battery status button
Angle adjustment button
Rotation direction switch
Charging port
Power button
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
BATTERY INFORMATION
1. Battery specifications
Battery Material: Li-on
Battery Voltage: 3.6V
Battery Capacity: 2000mAh
Battery Model: 18650
2. Working time: Around 1 hour (fully-charged & no-load)
3. Charging time: The battery must be fully charged before it is used for the first time.
The battery should be charged for around 5 hours the first time it is used. After that, it
takes around 1.5-3 hours to charge this product. Under any circumstance, do not
charge this product for more than 5 hours as it may shorten battery lifetime. Leave at
least 30 minutes of interval time before you charge this product again.
4. Check battery status
To check the battery status, you need to press the battery status button to activate
the indicator light. Read the current battery level as shown below:
Note:
1. Do not use the product when it is being charged.
2. Do not disassemble this product under any circumstances.
3. Do not expose the battery to water.
4. Do not store this battery in a high-temperature environment (above 40℃).
5. You should charge this product indoor instead of outdoor. When charging this
product, the optimum ambient temperature is around 20℃.
6. Please dispose the battery according to local rules and regulations.
7. Under extreme environment, electrolyte inside the batteries may leak. Avoid any
contact with the leaking electrolyte. If the electrolyte gets into your eyes or onto
your skin, flush with water for at least 10 minutes and consult a doctor immediately.
8. Do not short-circuit the battery, which may cause fire hazard.
9. If the battery is damaged, do not charge it.
EN-2
Current battery level
100%
50%
Less than 30%
Indicator light
Green+Yellow+Red lights
Yellow+Red lights
Red light
Safety Instructions
1. Please wear personal protective equipment such as gloves, shoes, goggles, face
masks, etc. Do not wear rings. Wear close-fitting clothing. Protect your hair.
2. If you are not going to use this product for a long time, please disconnect the
charging cable from the product.
3. Please use this product in a tidy and well-lit environment
4. Place and store this product in a dry area. Keep it away from heat sources and
explosive goods.
5. This product is for home use only.
6. Do not work close to people, children in particular. Keep this product beyond the
reach of children.
7. This is not an anti-drop tool. Make sure to hold this tool steadily.
8. When drilling metal sheets, you need to place a block of wood under the metal
sheet. Otherwise, the metal sheets may spin out of control.
9. It is forbidden to use this tool on anything with an electric charge. When you are
using this tool, make sure that there is no wire or cables around (a metal detector
may need to be used for this purpose). Do not touch the chuck, socket or drill bit
with you hand.
10. Do not try to open, dismantle the tool. Only professionals using original parts are
allowed to fix or maintain this tool .
11. This tool does not require special maintenance. The same applies to the electric
part of the tool.
12. Plastic parts should be cleaned only after disconnecting the charging cable from
the tool. Do not immerse the tool. Clean the plastic part using soft and damp
cloth. It is forbidden to clean this product with organic solvents, alcohol or
gasoline.
OPERATION GUIDANCE
How to charge this product?
Step 1: Insert USB port of the charging cable to an adapter (not included).
Step 2: Insert the DC port of the charging cable to the charging port of the
screwdriver. When the product is being charged, the red indicator light would be
solidly on. When the product is fully charged or disconnected from the charging
cable, the red indicator light would be off.
EN-3
Note: Do not use the product when it is being charged.
How to use this product?
Step 1: Insert a drive bit
Pull the knurled collar of the chuck towards the driver body and insert a driver bit into
the chuck. Release the collar to lock the inserted driver bit. Check to make sure that
the driver bit is firmly locked. Or, you could insert the extension bit into the chuck first.
Then, connect a driver bit with the extension bit.
Note:
1. This product is compatible with screwdriver bits which have a 1/4 inch (6.35mm)
hexagonal shaft.
2. To remove the drive bit or the extension bit, you need to pull the knurled collar of
the chuck towards the driver body first.
Step 2: Select the direction of rotation
1. Press the rotation direction switch to the right to
tighten screws. The bit will rotate clockwise.
2. Press the rotation direction switch to the left to
remove screws. The bit will rotate
counter-clockwise.
Step 3: Adjust the torque
Twist the torque adjustment collar to change the torque setting. This product covers
3.5 ~ 6 newton meters (31 ~ 51inch-pound) torque range, with 7-stage torque
settings.
▪When the number 1 is aligned with the arrow/white spot on top of the torque
adjustment collar, the torque is the smallest.
EN-4
Step 4: Power on the product
Point the screwdriver to the target object. Press and hold the power button to start
drilling. Release the power button to turn off. The LED flashlight would turn on
automatically when the product is operating.
How to adjust the angle of the handle?
1. Hold the front of the screwdriver in one hand.
2. Press in the angle adjustment button and twist the handle clockwise to change to
in-line grip or anticlockwise to change to pistol grip.
3. Release the angle adjustment button.
PRODUCT SPECIFICATIONS
Screwdriver: No-load speed: 200 rpm
Chuck size: 1 / 4″=6.35mm (male)
Torque Range: 3.5 ~ 6 N.m
7-stage torque settings
Acoustic pressure level: Lpa < 70dB(A)
Emitted vibration: Acceleration < 2.5 m/s2
USB Cable (Output): DC 5V 1A
▪When the icon is aligned with the arrow/white spot on top
of the torque adjustment collar, the torque is the largest.
Note:
1. Before actual driving, you could make a pilot hole. Test to find
out the required torque by driving into the targeted material.
2. The the arrow/white spot of the adjustment collar cannot be
locked in a middle position.
EN-5
WARRANTY
Our company provides customers with warranty of 12 months from the date of
purchase.
CONTACT US
For any inquiries or comments concerning our products, please send an email to
EN-6
Vielen Dank für die Auswahl von URCERI.
Bevor Sie unseren Artikel verwenden, lesen Sie bitte die Bedienungsanleitung
sorgfältig durch.
PRODUKTSÜBERSICHT
DE-7
SND133
Sechskantfutter
Gerändelter Kragen
Einstellring für Drehmoment
LED Leuchte
Signallampen
Batteriestatus-Taste
Winkeleinstellungstaste
Drehrichtungsschalter
Aufladestation
Power Taste
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
Table of contents
Languages:
