UNITED UHC-862 User manual

CONVECTOR HEATER

USER INSTRUCTIONS

Model: UHC-862

IMPORTANT Read these instructions fully before using the heater.

Retain these instructions for future reference.

ASSEMBLY OF THE HEATER

Before using the heater, the feet (supplied

separately in the carton), must be fitted to the

unit. These are to be attached to the base of

the heater using the 4 screws provided,

taking care to ensure that they are located

correctly in the bottom ends of the heater side

moldings

SAFETY INSTRUCTIONS (to be read before operating the heater)

Do not use the heater unless the feet are correctly attached.

Ensure the power supply to the socket into which the heater is

plugged is in accordance with the rating label on the heater and that

the socket is earthed.

Keep the mains lead away from the hot body of the heater.

Do not use this heater in the immediate surroundings of a bath, a

shower or a swimming pool.

Never place the heater where it may fall into a bathtub or other water

container.

Do not use outdoors.

Do not cover or obstruct any of the heat outlet grilles or the air intake

openings of the heater.

Do not place the heater on carpets having a very deep pile.

Always ensure that the heater is placed on a firm level surface.

Ensure that the heater is not positioned close to curtains or furniture

as this could create a fire hazard.

Do not position the heater in front of, or immediately below, a wall

socket.

Do not insert any object through the heat outlet or air intake grilles of

the heater.

Do not use the heater in areas where flammable liquids are stored or

where flammable fumes may be present.

The appliance is not intended for use by young children or infirm

persons without supervision.

Young children should be supervised to ensure that they do not play

with the appliance.

Always unplug the heater when moving it from one location to

another.

Do not use the heater if the power cord is damaged. If the power

cord is damaged it must be replaced by a recognized service agent or

other qualified person.

The appliance in not intended for use by person (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible

for their safety.

Do not cover. If covered, there is the risk of overheating or even fire.

In order to avoid a hazard due to inadvertent resetting of the thermal

cutout, this appliance must not be supplied through an external

switching device, such as a timer, or connected to a circuit that is

regularly switched on and off by the utility.

-Children of less than 3 years should be kept away unless

continuously supervised.

-Children aged from 3 years and less than 8 years shall only switch

on/off the appliance provided that it has been placed or installed in its

intended normal operating position and they have been given

supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children aged from 3

years and less than 8 years shall not plug in, regulate and clean the

appliance or perform user maintenance.

-CAUTION- Some parts of this product can become very hot and

cause burns. Particular attention has to be given where children and

vulnerable people are present.

OPERATION OF THE HEATER

NOTE:- It is normal when the heaters are turned on for the first time

or when they are turned on after having not been used for a long

period of time the heaters may emit some smell and fumes. This will

disappear when the heater has been on a short while.

Choose a suitable location for the heater, taking into account the

safety instructions above.

Insert the plug of the heater into a suitable

socket.

Turn THERMOSTAT KNOB fully in a clockwise

direction to the maximum setting.

Turn on the heating elements by means of

HEATER SWITCHES on the side panel. Turn

on the heating elements by means of

HEATER SWITCH on the side panel. You

may obtain three heating settings

(750/1250/2000W) by turning the heater

switch knob in a clockwise direction.

When the desired room temperature has been

reached, the thermostat knob should be turned

slowly anti-clockwise until the thermostat is

heard to click off and the lights on the element

switches are seen to go out. After this the heater will keep the air

temperature in the room at the set level by switching on and off

automatically.

PROTECTION AGAINST OVERHEATING

− An additional fitted safety thermostat protects the heater against

overheating and switches it off automatically. The service lamp

then goes out.

− If the device switches itself off, disconnect the mains plug from

the socket. The heater is ready for service again after a short

cooling-off phase (approx.15 minutes). Plug the mains plug

back into the socket.

− If this repeats itself, first check whether the thermostat switch is

set correctly or if objects hinder the heating operation.

CLEANING THE HEATER

Always un-plug the heater from the wall socket and allow it to cool

down before cleaning.

Clean the outside of the heater by wiping with a damp cloth and buff

with a dry cloth. Do not use any detergents or abrasives and do not

allow any water to enter the heater.

STORING THE HEATER

When the heater is not used for long periods of time, it should be

protected from dust and stored in a clean dry place.

Note: this appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance.

When replacing old appliances with new ones, the retailer is legally

obligated to take back your old appliance for disposals at least free of

charge.

NOTICE ABOUT RECYCLING

Your product is designed and manufactured with

high quality materials and components which can

be recycled and reused.

This symbol means that electrical and electronic

equipment, at their end-of-life,

should be disposed of separately from your

household waste. Please dispose of this equipment at

your local community waste collection/ recycling centre.

In the European Union there are separate collection systems for used

electrical and electronic products.

Please help us to conserve the environment we live in!

DECLARATION OF CONFORMITY

Herewith, Amiridis-Savvidis S.A. states that this product, complies

with the requirements of below directives:

EMC-Directive: 14 / 30 / EU

Low Voltage Directive: 14/ 35 / EU

CE Marking: 93 / 68 / EEC

RoHS Directive: 11 / 65 / EU

The detailed declaration of conformity can be found at

www.united-electronics.gr

Exclusive importer in Greece:

Amiridis – Savvidis S.A.

87A, 17th Noemvriou str, P.C. 55534

Thessaloniki – Greece

T: +302310944944 | F: +302310944940

www.amiridis-savvidis.gr

Table of contents

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide