Unical 16,5 Operation instructions

.it

USER OPERATING INSTRUCTIONS

16,5 - 16,5 C

Dear Customer,

ank you for having chosen one of our products, the result of many years of experience and of an ongoing

quest for higher quality in terms of safety, reliability and performance.

In this manual, you will nd all the information and useful advice to be able to use your product in the utmost

safety and eciency.

We remind you that the appliance must be commissioned by our Author-

ised Service Centre (Law 37/2008) which will check the installation and ll

out the warranty.

• Incorrect installation, maintenance that is not performed properly, and improper use of the product relieves

the manufacturer from any possible damage resulting from use of the stove.

• e appliance must not be used as an incinerator nor must fuel other than pellets be used.

• is manual has been draed by the manufacturer and is an integral part of the product. It must remain with

it during its entire lifetime. Should the product be sold or transferred, always make sure that the booklet is

present as the information it contains is addressed to the purchaser and to all those involved in its installa-

tion, use and maintenance.

• Read the instructions and technical information in this manual carefully before proceeding with installation,

use or any intervention on the product.

• Abiding by the indications provided in this manual guarantees your own safety and that of the product, as well

as working economy and a longer operational life.

• e careful designing and risk analysis performed by our company have produced a safe product. Nonethe-

less, before performing any type of operation, it is recommended to scrupulously comply with the instruc-

tions provided in this document and to always have it on hand.

• Pay the utmost attention when handling ceramic parts, where present.

• Check that the oor where the product is installed is perfectly level.

• e wall where the product is placed must not be made of wood or ammable material. e safety distances

must be maintained.

• While operating, some parts of the stove (door, handle, sides) can reach high temperatures. erefore pay

close attention and use the due precautions especially in the presence of children, elderly, disabled and ani-

mals.

• e stove must be installed by authorised personnel (Authorised Service Centre).

• Diagrams and drawings are supplied as examples; in an eort to pursue a policy of constant development and

renewal of the product, the manufacturer may perform the modications considered appropriate without

any prior notice.

• It is recommended to wear gloves when the stove is at its maximum power output to touch the pellet loading

door and the handle to open door.

• Do not install the stove in bedrooms.

Never cover the body of the stove in any way or obstruct the slits at the top

when the appliance is running. All of our stoves have been tested with in-

line ignition.

In case of a re, disconnect electric power, use an approved re extinguisher and, if needed, call the Fire Bri-

gade. en contact the Authorised Service Centre.

1.0 Standards and declaration of conformity

Our company declares that the stove complies with the following standards for the European Directive CE

marking.

• 89/336/EEC and 2004/108/EC (EMC directive) and subsequent amendments;

• 2006/95/EC (low voltage directive) and subsequent amendments.;

• 2006/42/EC (machinery directive);

• 89/106/EC (construction products);

• For installation in Italy, refer to UNI 10683/98 or subsequent amendments. e installer of the heating system

must issue the declaration of conformity according to L. 37/2008. All local and national laws and European

standards must be met when installing the appliance;

• EN 60335-1; EN 50165; EN 50366; EN 55014-1; EN 61000-3-2; EN 61000-3-3; EN 14785.

1.1 Information regarding safety

Please read this use and maintenance manual carefully before installing and activating the stove!

If you need explanations, contact your dealer or the Authorised Service Centre.

• e pellet stove must only be operated in domestic environments. is stove is controlled by a circuit board

making combustion fully automatic and controlled; the control unit regulates the ignition phase, 5 output

levels and the extinction phase, guaranteeing safe operation of the stove;

• e basket used for combustion allows most of the ashes produced by burnt pellets to drop into the ash pan.

Nonetheless, check the basket daily as not all pellets have high quality standards (use only quality pellets rec-

ommended by the manufacturer);

• e glass is equipped with a special air pass for self-cleaning. However, it is not possible to avoid a light grey

coating on the glass aer a few hours of work. is also depends on the type of pellet used. Some pellets soil

more than others.

1.2 Liability

With the delivery of this manual, we decline any civil or penal liability for accidents resulting from partial or

total failure to comply with the instructions contained herein.

We decline all liability resulting from improper use of the stove, from incorrect use by the user, from unauthor-

ised changes and/or repairs, from the use of non-original spare parts for this model.

e manufacturer declines any direct or indirect civil or penal liability due to:

• Lack of maintenance;

• Failure to comply with the instructions in the manual;

• Use which does not comply with safety directives;

• Installation which does not comply with the standards in force in the country;

• Installation by unqualied and untrained personnel;

• Changes and repairs not authorised by the manufacturer;

• Use of non-original spare parts;

• Events out of the ordinary.

• e stove must only be supplied with quality pellets with a 6 mm diameter, the

type recommended by the manufacturer;

• Before connecting the stove electrically, installation of the exhaust pipes with

the ue must be completed;

• e protective grate inside the pellet tank must never be removed;

• e environment where the stove is installed must have sucient air exchange;

• Never open the oven door while it is operating;

• When the stove is running, the surfaces, glass, handle and pipes become

very hot: they must only be touched with adequate protection;

• Keep/preserve the pellets in dry and moisture free rooms;

• Keep both the fuel and any ammable material at an adequate safety dis-

tance from the stove.

2.0 Function keys and display

Function keys

1. Increase temperature

e button allows you to increase the temperature from a minimum of 7°C to a maximum of 40°C.

2. Decrease temperature

e button allows you to decrease the temperature from a maximum of 40°C to a minimum of 7°C.

3. Setting button

Press the button to access the stove programming menu.

4. ON/OFF

Press the key for 2 seconds: the stove switches on or o.

5. Decrease output

e button allows you to decrease the output from a maximum of 5 to a minimum of 1.

6. Increase output

e button allows you to increase the output from a minimum of 1 to a maximum of 5.

SET

2.1 Display indications

7. Chronothermostat LED

Indicates that the weekly and/or daily programming is active.

8. “Smoke discharge” stove functioning LED

is is on when the stove is running.

9-10. Upper/lower display

Dierent stove operating modes are viewed on the display, as well as the temperature and work output set by

the user.

Should the stove malfunction, the display shows the relative error message (see paragraph “Particular cases”).

11. Remote control receiver

Reception sensor of commands given by remote control.

12. “Menu” setting LED

e LED ashes when the desired temperature is set.

13. Temperature LED

It switches on when the set temperature is reached. ECO appears on the display.

14. Remote control reception LED

e LED ashes when the remote control is used to change the temperature and/or output.

15. “Pellet” LED

e LED ashes whenever pellets are being loaded into the stove.

Function keys

1. Increase temperature

2. Decrease temperature

3. Menu setting

4. ON/OFF

5. Decrease output

6. Increase output

Display indications

7. Chronothermostat LED

8. Stove operating LED

9. Upper display

10. Lower display

11. Remote control receiver

12. “Menu” setting LED

13. Temperature LED

14. Remote control reception LED

15. Pellet LED

12 45

Remote control

1. Increase temperature

2. Decrease temperature

3. Increase output

4. Decrease output

2.2 Description of remote control (optional)

e remote control allows you to control the following

functions:

1. Increase temperature:

Pressing the button increases the temperature

from a minimum of 7°C to a maximum of 40°C.

2. Decrease temperature:

Pressing the button decreases the temperature

from a maximum of 40°C to a minimum of 7°C.

3. Increase output:

Pressing the button increases the output from a

minimum of 1 to a maximum of 5.

�

Fig. 1

Fig. 2

We remind you that the appliance must be commissioned by our qualied

Authorised Service Centre (Law 37/2008), which will check installation and

ll out the warranty.

When commissioning the stove, the room must be well-ventilated as un-

pleasant smells could develop coming from paint and grease in the tube and

shell.

4. Decrease output:

Pressing the button decreases the output from a maximum of 5 to a minimum of 1.

5. Switching stove on and o

Press the keys and simultaneously to switch the stove on or o.

�+

2.3 Recommendations

• Do not light the stove intermittently: this could cause sparks which shorten the lifetime of the electric com-

ponents;

• Do not touch the stove with wet hands: the electric components of the stove could cause discharges if handled

improperly. Only authorised technicians can deal with possible problems;

• Do not remove any screw from the rebox without rst having lubricated it;

• Never open the door when the pellet stove is operating;

• Make sure that the brazier basket is positioned correctly.

• All sections of the ue gas pipe must be able to be inspected. If xed, it must have inspection openings for

cleaning.

2.4 Loading pellets into tank

Pellets are loaded into the tank through the specic door at the back of the stove.

To load pellets, act as follows:

• Open the door at the top;

• Pour the desired amount of pellets into the tank, with due care (pour enough pellets to guarantee sucient

stove autonomy);

• Close the door.

3.0 Commissioning the stove

3.1 Stove ignition

• Fill the tank up 3/4 with the type of pellets recommended by the manufacturer;

• Connect the stove to a socket using the supplied cable;

• Press the switch at the back of the stove;

• e upper display will read “OFF” and the lower one, the current time;

• Press the key for 2 seconds. Aer a few seconds, the ue gas extractor fan and the ignition resistance

switch on and the text “FAN ACC” appears;

• Aer about 1 minute, the text “LOAD WOOD” appears, the stove loads the pellets and continues lighting the

resistance;

• When the proper temperature is reached, the display will read “FIRE ON”: this means that the stove has

moved to the last ignition phase at the end of which it will be fully operational;

ATTENTION!

Before ignition, a bit of smoke could ll the combustion chamber.

3.2 Stove extinction

To switch o the stove, press the key until the display reads “OFF”. Even aer extinction of the stove, the

ue gas extractor fan will continue running for a preset amount of time to guarantee quick exhaust of the ue

gas from the combustion chamber.

4.1 Programming stove - chronothermostat (optional)

is function allows you to program two ignitions and two extinctions of the stove during the day or to pro-

gram it weekly.

To enter programming:

• Press the key SET twice;

• Select the submenus (UT) using the keys and .

UT01: Setting current day and switching chronothermostat o.

If the parameter UT01 is set with the current day, for example Sunday (Day 7), select the day of the week to

which to associate PROGRAM 1 and/or PROGRAM 2 ignition.

Change output

It can be changed while the stove is working from a minimum of 1 and a maximum of 5. Press the button

to increase the value and the button to decrease it. e display indicates the output value.

Change temperature

e user can change the temperature at any time. To change the temperature, rst press SET and then press

or and select the desired value, which will appear on the lower display.

• Aer a few minutes, the upper display will read “ON 1-2-3-4-5” according to the output set, while the lower

display will show the room temperature;

• When the set temperature is reached, the upper display will read: “ECO” while the detected room temperature

will appear on the lower display;

• e temperature LED switches on when the set temperature is reached;

• Before lighting the stove, make sure that the brazier is clear of pellets and clean from residues of previous

combustion. Otherwise empty and clean it;

ATTENTION:

the brazier must be cleaned daily and the ash pan periodically. Reduced

or lack of cleaning can cause the stove to fail to ignite, damaging the stove

and the environment (possible emissions of non-combusted material and

soot).

Do not put pellets back into the brazier when they did not light.

4.0 Adjusting the stove

4.2 Programming the stove

Pressing the keys and allows you to select the desired value.

ATTENTION!

Switching on the chronothermostat while the stove is running stops the

digital clock inside the stove during the whole time operations in the

menu are carried out. It is recommended to act on the chronothermostat

menu while the stove is in standby (OFF).

UT02: Setting time.

Pressing the key again displays the text UT02 and the lower display views the current hour with ashing

dots. Adjust the hour by acting on the keys and .

UT03: Pressing the key again displays the text UT03 and the lower display views the minutes with ash-

ing dots. Adjust the minutes by acting on the keys and .

UT04: Reserved for Authorised Service Centre.

Pressing the key SET again displays the text UT04 reserved for the technician.

Do not modify the set parameters. Modications aer an improper access require the intervention of an au-

thorised technician NOT COVERED BY WARRANTY.

UT05: Indicates the time PROGRAM “1” starts. e time can be changed at 10 minute intervals by acting on

the keys and .

N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.

UT06: Indicates the time PROGRAM “1” nishes. e time can be changed at 10 minute intervals by acting on

the keys and .

N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.

UT07:

Allows you to select the day of the week to which to combine PROGRAM “1”.

Press the button to select the day of the week. Press the button to activate/deactivate stove igni-

tion. In the example, the stove is lit on Saturday and Sunday.

SET

Text Meaning

Day 1 Monday

Day 2 Tuesday

Day 3 Wednesday

Day 4 ursday

Day 5 Friday

Day 6 Saturday

Day 7 Sunday

OFF Chronothermostat o

Day 1 Day 2 Day 3 Day 4 Day 5 Day 6 Day 7

Monday Tuesday Wednesday ursday Friday Saturday Sunday

O 1 O 2 O 3 O 4 O 5 On On

EXAMPLE

Today is Monday. I want to switch the stove on automatically Monday, Tuesday, ursday and Sunday at 8:00

in the morning and switch it o at 16:00. Wednesday, Friday and Saturday I want to switch it on at 9:00 and

switch it o at 23:00.

ATTENTION!

When programs 1 and 2 have been set, the Timer LED is on. e Timer

LED remains o if programs 1 and 2 have not been set. If electric power

fails, a buer battery switches on, leaving the programmed time settings

unchanged.

e program will be as follows:

UT 01: day 1

UT 02: current hour

UT 03: current minutes

UT 04: reserved for technicians and installers

UT 05: 8:00

UT 06: 16:00

UT 07: On1-On2-O3-On4-O5-O6-On7

UT 08: 9:00

UT 09: 23:00

UT 10: O1-O2-0n3-O4-On5-On6-O 7

ATTENTION!

e temperature and output at which the stove operates during the time

periods with programming ON will be those of the last extinction.

5.0 Information on display

“OFF”

“OFF” the stove is o or in the extinction phase. E.g: current time 14:30.

UT08:

Indicates the time PROGRAM “2” starts. e time can be changed at 10 minute intervals by acting on the

keys and .

N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.

UT09: Indicates the time PROGRAM “2” nishes. e time can be changed at 10 minute intervals by acting on

the keys and .

N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.

UT10: Allows you to select the day of the week to which to combine PROGRAM “2”.

Press the button to select the day of the week. Press the button to activate/deactivate stove igni-

tion.

This manual suits for next models

Table of contents

Other Unical Boiler manuals

Unical

Unical ALKON 50c Datasheet

Unical

Unical IVEN B60 TFS 24 Quick start guide

Unical

Unical XC-K oil 230 Technical specifications

Unical

Unical ALKON 24 B 60 Operation instructions

Unical

Unical AIREX 2S Series Datasheet

Unical

Unical TRIOPREX N Series User guide

Unical

Unical TRISTAR 3G User manual

Unical

Unical KONm R 18 Datasheet

Unical

Unical SuperModulex 440 User guide

Unical

Unical SPK 150 User manual

Unical

Unical INOXIA GJ Series Datasheet

Unical

Unical DIATHER Series User manual

Unical

Unical Kone R 24 Operation instructions

Unical

Unical FOKOLUS 20 User guide

Unical

Unical FIREX 2S Instruction Manual

Unical

Unical CoR Series Datasheet

Unical

Unical PELLEXIA 80 Parts list manual

Unical

Unical ALKON 100 EXT Datasheet

Unical

Unical MODULEX EXT 150 User guide

Unical

Unical ALKON 50 kW Datasheet

Unical

Unical ALKON 35S C Operation instructions

Unical

Unical KONf 200 User manual

Unical

Unical ALLBIOMIX User manual

Unical

Unical modulex 360 Installation and operating instructions

Popular Boiler manuals by other brands

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES operating instructions

Radijator

Radijator BIO max 23.1 instruction manual

Brunner

Brunner BSV 20 Instructions for use

Buderus

Buderus Logamax GB062-24 KDE H V2 Service manual

Potterton

Potterton 50e Installation and Servicing Manual

UTICA BOILERS

UTICA BOILERS TriFire Assembly instructions

Joannes

Joannes LADY Series Installation and maintenance manual

ECR International

ECR International UB90-125 Installation, operation & maintenance manual

Froling

Froling FHG Turbo 3000 operating instructions

Froling

Froling P4 Pellet 8 - 105 installation instructions

U.S. Boiler Company

U.S. Boiler Company K2 operating instructions

Henrad

Henrad C95 FF user guide

NeOvo

NeOvo EcoNox EF 36 user guide

Potterton

Potterton PROMAX SL 12 user guide

Eco Hometec

Eco Hometec EC 25 COMPACT Technical manual

Viessmann

Viessmann VITODENS 200 Operating instructions and user's information manual

Baxi

Baxi Prime 1.24 installation manual

REXNOVA

REXNOVA ISA 20 BITHERMAL Installation, use and maintenance manual