Twister T4 User manual
TWISTERTRIMMER.COM
T4 TRIM SAVER
NORTH AMERICAN MODEL
PN: 21-00-000426_REV04
USER MANUAL
TWISTERTRIMMER.COM
TWISTERTRIMMER.COM pg | 1
TABLE OF CONTENTS
Important Safety Informaon
Parts and Tools
Assembled Trim Saver
Assembly
Inspecons
Cleaning
Troubleshoong
Warranty Informaon
Specificaons
Spare Parts and Accessories
Contact Us
2
5
9
10
19
20
24
25
28
29
30
TWISTERTRIMMER.COMpg | 2
IMPORTANT SAFETY INFORMATION
This manual is for the Twister T4 Trim Saver vacuum. In
this manual, the Trim Saver vacuum will simply be referred
to as the Trim Saver.
The Trim Saver is a high-speed and high-powered vacuum.
It requires special safety precauons to be pracced
during assembly and operaon to reduce the risk of
personal injury. Read this manual, including all important
safety informaon, danger, warning, and cauon signs
before assembling and using the Trim Saver.
Keirton is connually improving all its products. As a
result, engineering changes are somemes made. If appearances differ from this manual, please contact
Keirton Technical Support for assistance (see Contact Us on page 30).
Do not allow anyone to assemble or use the Trim Saver without this manual. A first-me assembler or
user of the Trim Saver should obtain proper instrucon from this manual.
General Safety Information
• Do not tamper with or bypass the Trim Saver’s safety systems. Failure to abide could
cause fatal injury.
• Do not assemble or operate the Trim Saver while red or under the influence of drugs,
alcohol, or medicaons.
• Do not wear loose clothing or jewellery when assembling or operang the Trim Saver.
• Confine long hair when assembling or operang the Trim Saver.
• Do not assemble, move, or clean the conveyors while power is connected to them.
• Do not remove safety labels from the machine. Replace any safety labels if they
become damaged or obscured.
• Keep visitors and children a safe distance from the conveyors.
CARELESS USE OF THE TRIM SAVER
OR ASSEMBLING IT WITHOUT
READING THE INSTRUCTIONS
AND ACCOMPANYING DANGER,
WARNING, AND CAUTION
NOTICES MAY RESULT IN
SERIOUS OR FATAL INJURY.
DANGER
!
TWISTERTRIMMER.COM pg | 3
Connection and Electrical Safety Information
• The Trim Saver requires a 120V, 15A circuit breaker.
• The Trim Saver must be used in connecon with a properly grounded receptacle. Refer to
Specificaঞons on page 20 to determine the correct electrical requirements.
• Observe all applicable building and electrical codes.
• Do not overload outlets as this can result in fire or electric shock.
• Do not use extension cords with a diameter narrower than 12AWG.
• Do not use extension cords longer than 50’ (15M).
• To power down the Trim Saver, switch it offusing the motor switch before unplugging
the machine.
• The motor is not water ght. Do not get the motor wet while cleaning to prevent electric
shock.
• Cover the end of the plug before cleaning to prevent electric shock.
Assembly Safety Information
• Substung factory parts with third-party parts may result in bodily harm or damage to
the Trim Saver.
• Do not skip any assembly steps. Complete all steps in order.
• Do not connect the Trim Saver to a power source unl it is fully assembled.
• The motor is heavy and fragile. Use two people to aach it to the rest of the machine.
Operation and Maintenance Safety Information
• Do not allow anyone to operate the Trim Saver unless it is fully assembled.
• Do not switch on the Trim Saver unless it is connected to the T4 trimmer.
• Do not disassemble the Trim Saver unless it is disconnected from power and the impeller
has come to a complete stop. The impeller may connue to spin for up to 30 seconds
aer stopping the Trim Saver.
IMPORTANT SAFETY INFORMATION
TWISTERTRIMMER.COMpg | 4
IMPORTANT SAFETY INFORMATION
• Clean the Trim Saver regularly.
• Ensure the Trim Saver is powered offbefore conducng any maintenance.
• To avoid electric shock, do not aempt to service electrical components on the
Trim Saver unless you are a trained electrician.
• Do not aempt maintenance unless directed by Keirton Technical Support.
• Some repair will require a qualified service technician who is trained in machinery
maintenance, service, and repair.
TWISTERTRIMMER.COM pg | 5
Parts: Components
Fig. 1
1 2 3 4 5
678910
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
PARTS AND TOOLS
TWISTERTRIMMER.COMpg | 6
Reference Descripঞon Part Number Quanঞty
1Caster 23-0146 4
2Base Plate 23-0215 1
3Motor Support 23-0206 1
4Lid Holder 23-0208 1
5Saddle Support 23-0205 1
6Hose Saddle 23-0198 2
71.5hp Vacuum Fan and Motor Assembly 23-0213 1
8Filter Adapter Gasket 23-0230 1
9Filter Adapter 23-0209 1
10 Cart Handle 23-0204 1
11 CS-12 Cyclone Assembly 23-0202 1
12 Cyclone/Lid Gasket 23-0241 2
13 Stainless Steel Bin Lid 23-0243 1
14 Lower Lid Gasket 23-0244 1
15 Stainless Steel Bin 23-0242 1
16 Cleaning Flange 11-00-000100 and
11-00-000101
1 (2 pieces)
17 6” Hose Cuff23-0132 2
18 6” Hose 23-10175A 1
19 6” Hose Clamp 23-01-001152 2
20 200 White Mesh (70 Micron) Filter Bag 23-0246 1
21 300 White Mesh (40 Micron) Filter Bag 23-0247 1
22 7” Filter Bag Clamp 23-0218 1
23 5” Hose Cuff23-01-002127 2
24 5” Hose 23-01-127675 1
25 5” Hose Clamp 23-01-001127 2
PARTS AND TOOLS
TWISTERTRIMMER.COM pg | 7
Parts: Fasteners
The fasteners are placed in labelled bags that pertain to the different stages of assembly. For easiest
assembly, do not open these bags unl the instrucons say to do so.
Reference Descripঞon Part Number Quanঞty
1⁄” Star Lock Washer 13-02-000411 52
2⁄” Flat Washer 13-0018 4
3⁄” Flat Washer 13-02-000014 12
4⁄” Silicone Washer 23-0248 6
5⁄”–20 Nyloc Nut 13-0062 6
6⁄”–18 Nyloc Nut 13-0064 12
710–32 Wing Nut (connected to cleaning flange) 13-0168 6
8⁄”–18 x ⁄” Hex Head Bolt 13-08-516158 46
9⁄”–18 x 1” Hex Head Bolt 13-08-516110 4
10 ⁄”–20 x 1” Hex Head Bolt 13-08-142110 6
11 ⁄”–18 x 1.5” Hex Head Bolt 13-08-516115 2
Fig. 2
1 2 3 4
5 6 7
8 9 10 11
PARTS AND TOOLS
TWISTERTRIMMER.COMpg | 8
Tools Needed
Reference Descripঞon Quanঞty
1⁄” Wrench 2
2⁄” Wrench 2
Fig. 3
12
PARTS AND TOOLS
Other manuals for T4
3
Table of contents
Other Twister Vacuum Cleaner manuals
