Tuff Mount C7016 User manual

6. Installing the Display

INSTALLATION MANUAL

LCD Ceiling Mount

C7016

55"

MAX

75x75 100x100

200x100/200x200

300x300/400x400

ISSUED: DEC. 2015

30kg

(66lbs)

RATED

30kg

(66lbs)

RATED

7. Adjustment

Use the tilt adjusting knob to adjust your display to the desired angle then tighten it.

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).

• Please contact your dealer if you have any questions.

Tighten all screws but do not over tighten.

Lift the display and match the holes on your display with the holes on the VESA plate. Secure your

display to the mount by tightening screws.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

TVTV

CAU T ION: DO NOT EXCEED

RATED LISTED WEIGHT. SERIOUS

INJURY OR PROPERTY DAMAGE

MAY OCCUR!

M-A/ B/M-CM- M-F/M-G

M-C

M-G

M-E

M-

M-G

M-H M-I

180°

+20°

-20°

FOR CUSTOMER SERVICE CALL 855-449-8833 TUFF

M-E

M-

M-G M-I

M-H

M-C

M-D

M-E M-G M-H

M-H

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.

If any parts are missing or faulty, telephone your local distributor for a replacement.

Package M

Package W

concrete anchor

W-B

(x4)

ST6.3x55 (x4)

W-A

D8 (x4)

M-G

washer

D (x4)

M-F

5 washer small spacer

M-H

(x8)

M8x20

M-C

(x4)

M5x14

M-A

(x4) M6x14

M-B

(x4)

plastic cover

(x1)

grip holder (x1)

ceiling plate

(x1)

plastic bushing (x2)

outer column (x1)

inner column

(x1) M8 washer (x2)

M6x45(x3)

M8x45(x1)

knob (x1)

plastic pad (x1)

M6 nut (x3)

M8 nut (x1)

washer (x1)

M8x20 (x1)

VESA plate

(x1)

D8 (x2)

washer

NOTE: Read the entire instruction manual before you start installation and assembly.

WARNING

• Do not begin the installation until you have read and understood all the instructions

and warnings contained in this installation sheet. If you have any questions

regarding any of the instructions or warnings, please contact your local distributor.

• This mounting bracket was designed to be installed and utilised ONLY as

specified in this manual. Improper installation of this product may cause damage

or serious injury.

• This product should only be installed by someone with good mechanical ability

who has basic building experience and fully understands this manual.

• Make sure that the supporting surface will safely support the combined weight of

the equipment and all attached hardware and components.

• If mounting to wooden joist ceiling, make sure that mounting screws are anchored

into the center of the joist. The use of a stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position

the equipment.

• Tighten screws firmly, but do not over tighten. Over tightening can cause damage

to the items, This greatly reduces their holding power.

• This product is intended for indoor use only. Using this product outdoors could

lead to product failure and personal injury.

VESA adapter

(x2) VESA adapter (x2)

M6 screw

(x8)

M8x30 (x4)

M-E

M6x30 (x4)

M-D

small spacer (x4)

M-I

WARNING

• Make sure that mounting screws are anchored into the center of the joist. The use of a stud

finder is highly recommended.

• Installers must verify that the supporting surface will safely support the combined weight of the

equipment and all attached hardware and components.

1a. For Wooden Joist Ceiling Mounting

Drill two

pilot holes

Screw the

ceiling plate

onto the

ceiling

3mm

ø 4.5mm

(ø 3/16")

55mm

(2.2")

55mm

(2.2")

Find and mark

the exact location

of mounting holes

W-A

Hang the ceiling plate so that the screws

fit into the keyhole openings. Turn the

ceiling plate into place and then tighten

the screws.

1b. Solid Brick and Concrete Block Mounting:

Installers must verify that the supporting surface will safely support the combined weight of

the equipment and all attached hardware and components.

WARNING

1b. For Solid Brick and Concrete Mounting

Drill four

pilot holes

Screw the

ceiling plate

onto the

ceiling

3mm

Hang the ceiling plate so that the screws fit into the keyhole openings. Turn the ceiling plate into place .

Do not tighten screws at this time. Fix the ceiling plate using the two other screws and then tighten all

the screws!

60mm

(2.4")

60mm

(2.4")

ø 10mm

(ø 3/8")

Mark the exact

location of

mounting

holes

W-A

W-B

W-A

Tighten both screws leaving

a 3mm space from the ceiling.

Tighten both screws

leaving a 3mm space

from the ceiling.

2. Installing the Outer Column to the Ceiling Plate

3. Installing the Inner Column and Routing Cables

Insert the plastic bushing and the inner column into the outer column and fix them at the desired height

using the correct combination of screws and nuts.

Run the power cable

through columns.

5. Installing the VESA Plate

4. Assembling the VESA Plate

Other Tuff Mount Rack & Stand manuals

Tuff Mount

Tuff Mount TM-200HD Assembly instructions

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 