Tru CORDLESS RC-300MC User manual

IMPORTANT SAFEGUARDS

When using electrical appliances especially when children are present, basic safety precautions should always be

followed to reduce the risk of re, electric shock, and/or injury to persons, including the following:

1. READ ALL INSTRUCTIONS.

2. To protect against re, electrical shock, or injury to persons DO NOT put charging cord, charger adapter or appliance in water or

other liquid.

3. This appliance is not intended for use by children or by persons with reduced physical, sensory, or mental capabilities, or lack of

experience and knowledge. Close supervision is necessary when any appliance is used near children. Children should be supervised

to ensure that they do not play with the appliance.

4. Unplug charger adapter from outlet when not in use, before putting on or taking off parts and before cleaning. To unplug, grasp the

charger adapter and pull from the outlet. Never pull from the charging cord.

5. Avoid contacting moving parts.

6. Do not operate or charge the appliance with a damaged charging cord or charger adapter, or after the appliance malfunctions, or

is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on

examination, repair, or adjustment.

7. The use of attachments not recommended or sold by the appliance manufacturer may cause re, electric shock or injury.

8. Do not use outdoors.

9. Do not let charging cord hang over edge of table or counter or touch hot surfaces.

10. Do not place on or near a hot gas or electric burner, or in a heated oven.

11. Keep hands and utensils out of the container while chopping to prevent the possibility of severe injury to persons or damage to the

unit. A scraper may be used but must be used only when the unit is not running.

12. Never add to container while appliance is operating.

13. To turn the motor housing unit off, release the speed buttons (HI or LOW) located on the top of the unit.

14. To reduce the risk of injury with the unit, never place the chopping blade into the motor housing unit. Place the chopping blade into

the glass chopping bowl and then assemble chopper collar and then motor housing unit onto the chopping bowl.

15. Container must be properly in place before operating the appliance.

16. Blades are sharp, are not locked in place and are removable. Handle with care. When handling blades, always hold by the shaft. To

avoid a risk of injury, carefully remove the blades before pouring out food contents.

17. Do not use an extension cord. Plug charger directly into an electric outlet. Use only with the charger provided with the appliance. Do

not attempt to use this charger with any other product. Likewise, do not attempt to charge this appliance with any other charger. Do

not use appliance for other than intended use.

18. Do not incinerate this appliance even if it is severely damaged. The batteries can explode in a re.

19. Do not use appliance for other than intended use.

SAVE THESE INSTRUCTIONS

This appliance is for HOUSEHOLD USE ONLY.

The charger may be plugged into an AC electrical outlet (ordinary household current). Do not use any other electrical outlet.

DO NOT USE THE USB CHARGER IF THE LINE CORD OR PLUG SHOWS ANY DAMAGE

Only use Tru Model P12DUSB050200 US charger (Input:100-240VAC, 50/60Hz, 0.3A, Output:5.0VDC, 2.0A) to charge the chopper

Model RC-300MC. Do not attempt to charge the motor housing unit with any other charger.

CHARGER / USB CORD SAFETY TIPS

1. Never pull or yank on charging cord.

2. To insert the charger adapter, grasp it rmly and guide it into outlet.

3. To disconnect, grasp charger and remove it from outlet. Do not pull on the cord.

4. Before each charging, inspect the charging cord for cuts and/or abrasion marks. If any are found, this indicates that the

charging cord should be replaced.

5. Never wrap the cord tightly around the appliance, as this could place undue stress on the cord where it enters the charger

adapter or charging port on the appliance and cause it to fray and break.

CORDLESS CHOPPER FEATURES

1. High capacity lithium/ion battery

2. Light, quiet, convenient and easy to clean

3. Easy to charge

4. 2 Operation Speeds

5. Stainless steel high speed cutting blade

6. Glass chopping bowl with storage lid

7. Non-skid trivet

PREPARING FOR USE

1. Carefully unpack the motor housing unit and all parts. Remove any tape, labels or packaging materials.

2. Wash all product pieces carefully except for the motor housing unit with warm, soapy water. Rinse and dry thoroughly.

3. Wipe exterior surfaces of the motor housing with a soft, moist cloth to remove dust particles collected during packing and handling.

NEVER IMMERSE THE MOTOR HOUSING, CHARGING CORD OR CHARGER ADAPTER IN WATER OR ANY OTHER LIQUID.

4. Be sure all parts are properly assembled and in place before use.

HOW TO CHARGE

1. Open the charging port on the motor housing. Attach micro end of charging cord to the motor housing.

2. Attach the USB connector (larger end) on the charging cord to the charger adapter.

3. Plug the charger adapter into the wall outlet.

4. Indicator lights will ash while charging. The lights will stop ashing once the unit is fully charged. See Indicator Light section for

details. Note: The unit is shipped with approximately 30% charge in the batteries. One or two lights will be illuminated during use.

The unit will operate properly without charging. It is recommended to fully charge before rst use for best performance.

5. It will take approximately 5 hours to fully charge the unit.

ASSEMBLING THE CHOPPER

Hold the chopper blade by the shaft and push onto the metal shaft in the bottom of the chopping bowl until secure. Align the U-shape

openings on the chopper collar with the U shapes in the chopping bowl and push in place. Align the pins in the chopper collar with the

small openings in the motor housing and place the motor housing onto the chopper collar. The motor housing should t ush with no gaps.

HOW TO USE

This chopper can also be used just like a normal chopper but without the cord!

1. Place chopping blade onto metal shaft in the bottom of the chopping bowl.

2. Place the chopping bowl on the non-skid trivet on a level table top surface (see Figure A)

3. Place food to be chopped into the bowl. Do not overll.

4. Place the chopper collar and motor housing onto the bowl. The lights will ash on to indicate the unit is ready to use.

5. Press the I (low) or II (high) speed button on top of the motor housing.

6. Allow the chopper to work through the chopping process. Do not shake or move the chopper while operating.

7. When chopping has nished, release the speed button and the unit will stop.

8. Ensure the blade has completely stopped before removing the motor housing and chopper collar.

9. Remove the chopping blade by grasping the shaft rmly and lift up. Be careful, the blades are sharp!

10. After the chopping blade has been removed the ingredients can be removed from the chopping bowl.

11. Do not use the chopper for longer than 1 minute continuously. After 1 minute of continuous use, the unit may become over-heated.

Allow the unit to rest for at least 5 min before resuming use.

12. The lights will extinguish as the battery life reduces. A fully charged unit will show all three lights. When only the lowest light is

illuminated and ashing, this incidates that the unit needs to be charged.

If food becomes lodged around the blender blade or chopping blade during use:

1. Release the speed button and wait for the blades to stop.

2. Remove the motor housing and collar.

3. Use a spatula to carefully dislodge the food. Do not use ngers as the blades are sharp.

4. After the food has been removed and blades are clear, reassemble the collar and motor housing and continue use.

Figure A

INDICATOR LIGHTS

The motor housing indicator lights provide feedback for different situations.

Battery Life During Use:

As the motor housing is used and the battery begins to drain during performance, the indicator lights will extinguish in sequence from

the top to the bottom to indicate how much battery capacity is left.

66% to 100% of capacity: Lights 1, 2 and 3 will all be illuminated

33% to 65% of capacity: Lights 1 & 2 will be illuminated

20% to 32% of capacity: Light 1 will be illuminated

If < 20% of capacity: Light 1 ashes and the unit needs to be charged

Charging Indication:

Indicator lights will also provide feedback during the charging process:

If battery capacity is less than 33%, Lights 1, 2 and 3 will ash while charging.

If battery capacity is within 33%-65%, Light 1 will illuminate solid and Lights 2 and 3 will ash.

If battery capacity is within 66%-99%, Lights 1 and 2 will illuminate solid and only Light 3 will ash.

If battery capacity is greater than 99%, Lights 1, 2 and 3 will illuminate solid.

Overloading Indication:

Note: The motor housing has an automatic protection system that will not allow overloading. If the load is too large, the unit will

automatically shut off. If the unit senses an overload situation, all 3 lights will ash 5 times and the unit will turn Off. Release the speed

button and the lights will turn off. Reduce the load on the blender or the chopper, allow it to rest for more than 15 minutes and then

resume use. Do not attempt to charge the unit when it indicates an overload situation. Allow the unit to rest for 15 minutes before

charging the unit.

Do not expose a battery pack or appliance to re or excessive heat. Exposure to re or temperatures above 265°F/130°C may cause an

explosion.

USER MAINTENANCE INSTRUCTIONS

This appliance contains no user serviceable parts. Do not try to repair it yourself. Have servicing performed by a qualied repair person

using only identical replacement parts. This will ensure that the safety of the product is maintained.

Dispose of the appliance at the end of its life span according to local environmental considerations and requirements.

TO CLEAN:

NOTE: DO NOT PUT MOTOR HOUSING OR CHOPPER COLLAR IN DISHWASHER. Wipe motor housing and chopper collar dry or

allow to air dry before storing. Do not use abrasive cleaners or steel wool.

NEVER IMMERSE MOTOR HOUSING, CHARGER ADAPTER OR CHARGING CORD IN WATER OR ANY OTHER LIQUID. Do not

place motor housing or chopper collar in dishwasher. The chopping blade, blender blade, chopping bowl, blender jar, blender collar and

lids can be placed in the dishwasher. Do not use abrasive cleaners or steel wool.

TO STORE:

• Be sure all parts are clean and dry before storing. Never store it while it is wet.

• The unit can be stored for up to 3 months with a fully charged state. If storing for longer than 3 months the unit should be charged

before next use.

• Store in a dry area in an ambient temperature of 40°F to 95°F.

Table of contents

Popular Food Processor manuals by other brands

INNOLIVING

INNOLIVING INN-727 user manual

Berkel

Berkel C32 Specifications

Beko

Beko CHP5554W user manual

KitchenAid

KitchenAid 5KFP0719 use and care manual

QUIGG

QUIGG KM 2017Wi.20 Instructions for use

Lakeland

Lakeland PRESS AND CHOP 31557 Instruction booklet

Bosch

Bosch MMR08 GB Series instruction manual

HOFFEN

HOFFEN Chef Express T9532 instruction manual

Garland

Garland 852 ZG instruction manual

Robot Coupe

Robot Coupe CL50 Gourmet manual

SAPIRHOME

SAPIRHOME SP-1111-K instruction manual

Moulinex

Moulinex DJ3051 manual

Bosch

Bosch MUM5 instruction manual

cecotec

cecotec Mambo Touch instruction manual

KitchenAid

KitchenAid 9KFC0516 manual

Black & Decker

Black & Decker hc 300 Use and care

Gorenje

Gorenje SBR 1000 DV instruction manual

Arzum

Arzum AR 1128 manual