Trotec IR 2000 C User manual
TRT-BA-IR2000C-IRS2010-TC211001TTRT08-001-EN
IR 2000 C / IRS 2010
EN
OPERATING MANUAL
RADIANT HEATER
2 EN
radiant heater IR 2000 C / IRS 2010
Table of contents
Notes regarding the operating manual.................................2
Safety .....................................................................................2
Information about the device................................................5
Transport and storage...........................................................6
Assembly and start-up..........................................................7
Operation .............................................................................10
Errors and faults..................................................................11
Maintenance ........................................................................12
Technical annex...................................................................13
Disposal ...............................................................................13
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of hot surface
This symbol indicates dangers to the life and health of
persons due to hot surface.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
IR 2000 C
https://hub.trotec.com/?id=45862
IRS 2010
https://hub.trotec.com/?id=45863
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use.
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged
from 8years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
EN 3
radiant heater IR 2000 C / IRS 2010
Warning
Children of less than 3years should be kept away from
the device unless continuously supervised.
Children aged from 3years and less than 8years shall
only switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
Children aged from 3years and less than 8years shall
not plug in, regulate and clean the appliance or
perform user maintenance.
Warning
Do not use the device in small rooms if persons are
present who cannot leave the room independently and
who are not under constant supervision.
• Do not use the device in potentially explosive rooms or
areas and do not install it there.
• Do not use the device in aggressive atmosphere.
• Let the device dry out after a wet clean. Do not operate it
when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not use the device as source of ignition.
• Do not cover the device during operation.
• This appliance is not a toy. Keep away from children and
animals. Do not leave the device unattended during
operation.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The mains connection must correspond to the
specifications in the Technical annex.
• Insert the mains plug into a properly fused mains socket.
• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the power cable is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
• When installing the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions according to the technical
data (chapter Technical annex).
• Keep a safety distance of at least 1.80m between the
device's radiator side and all combustible materials such
as textiles, curtains, beds and sofas.
• Allow the device to cool down before transport and/or
maintenance work.
• The device must not be installed directly beneath a socket.
• The device must not be used with a programming switch,
timer, separate remote control system or similar
equipment that switches the device on automatically, as
this could cause a fire hazard if the heater is covered or
positioned incorrectly.
• Do not use the device if it has been dropped or if it shows
visible signs of damage.
Intended use
Use the device for heating surfaces in roofed and non-roofed
outdoor areas.
Intended use comprises:
• heating surfaces
– in storage facilities,
– in construction areas,
– in containers,
– in the catering trade,
– at trade fairs and events.
4 EN
radiant heater IR 2000 C / IRS 2010
Foreseeable misuse
• The device is not intended for industrial use.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device for heating in vehicles.
• Do not use this device in the vicinity of fuel, solvents,
varnishes or other easily inflammable vapours or in rooms
where these substances are stored.
• The device may not be used as a heating device for
babies / children or animals.
• Do not install the heating device in immediate proximity to
swimming pools!
• The device may not be exposed to moisture or weather
effects (rain, sunlight).
• Any use other than the intended use is regarded as a
reasonably foreseeable misuse.
Any unauthorised changes, modifications or alterations to the
device are forbidden.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the operating manual, especially
the Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist electrical companies or by
Trotec.
Symbols on the device
Symbols Meaning
This symbol located on the device indicates that it
is prohibited to place objects (such as towels,
clothes etc.) above or directly in front of the
device.
In order to avoid overheating and fire hazards, the
heater must not be covered.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Do not touch the mains plug with wet or damp hands.
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of electrical voltage
Risk of electric shock!
Risk of an electric shock if the heating device comes
into contact with water in swimming pools!
Do not install the heating device in immediate
proximity to swimming pools!
Warning of hot surface
Parts of this appliance can become very hot and cause
burns. Particular attention is to be paid when there are
children or vulnerable persons present!
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
Improper installation entails a risk of fire.
Do not place the device on combustible ground.
Do not place the device on high-pile carpets.
Warning
Risk of injury due to infrared radiation!
Do not stay in the device's immediate vicinity for too
long. Do not look directly into the device for too long.
Observe the minimum distances.
Warning
In order to avoid overheating and fire hazards, the
device must not be covered!
EN 5
radiant heater IR 2000 C / IRS 2010
Warning
Coarse dirt particles on the heating rods can cause the
device to overheat. Fire hazard!
Remove coarse dirt particles from the heating rods
according to the Maintenance chapter before switching
on the device.
Behaviour in the event of an emergency
1. Switch the device off.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
Tilt protection
The device IRS2010 is equipped with a tilt protection. The tilt
protection is a safety device intended to minimize the risk of fire
in case the device is tipped over inadvertently. The device will
be switched off when knocked over (or if its upright position is
changed in any other manner).
The tilt protection switches the device off when it is inclined out
of its vertical position. The device can again be used as usual
only a few seconds after placing it back in vertical position and
on solid ground.
Information about the device
Device description
The device is used to quickly generate instant heat.
The device is based on the functional principle of heat
generation by infrared radiation, which is generated by a
halogen heating element. The infrared radiation is passed on to
the surrounding surfaces as heat radiation. Persons or objects
are heated directly.
Both heating levels can be selected on the device or by using
the remote control.
• suitable for roofed and non-roofed outdoor use
• IP55 type of protection– dust- and water-jet-proof
• approx. 5,000operating hours
• for stand mounting (IRS2010)
• for ceiling mounting (IR2000C)
• with tilt protection (IRS2010)
• silent operation
• 2 heating levels
• no dust circulation
6 EN
radiant heater IR 2000 C / IRS 2010
Device depiction
IR 2000 C
1
2
4
3
IRS 2010
1
2
4
5
6
3
7
No. Designation
1Mains switch
2LEDelement
3Control panel
4Grille
5Telescopic rod
6Foot
7Remote control
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Do not use the power cable to drag the device.
• Allow the device to cool down sufficiently.
Storage
Before storing the device, proceed as follows:
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Allow the device to cool down sufficiently.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust, if necessary
• Place no further devices or objects on top of the device to
prevent it from being damaged.
• Remove batteries from the remote control.
EN 7
radiant heater IR 2000 C / IRS 2010
Assembly and start-up
Scope of delivery
IR 2000 C
• 1x Device
• 2x Fastening chain
• 2x Carabiner hooks
• 1 x Remote control
• 1x Manual
IRS 2010
• 1x Device
• 3x Fixation plate
• 3x Wedge bolt
• 4x Fastening nut
• 2x Screw
• 1x Foot
• 3x Telescopic rod
• 1 x Remote control
• 1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
Warning of electrical voltage
Risk of injury due to incorrect assembly!
Local or national regulations may apply for installation.
We recommend to have the installation carried out by a
qualified electrician.
Warning
Risk of fire due to improper installation!
There is a risk of fire if the required minimum
distances are not observed.
Observe the “Installation” section in the “Assembly and
start-up” chapter and the technical data in the
“Technical annex” chapter.
Warning
The device must not be placed directly below a socket,
as the electrical cables may be hit when the device is
being mounted. This may cause an electric shock.
Observe the minimum distances for mounting the
device (see chapter Technical data).
Assembly of the IR2000C
üUse tools suitable for the intended task.
üTwo suitable ceiling holders are preassembled.
1. Attach one carabiner hook to each end of a fastening
chain.
2. Hook both carabiner hooks with the fastening chains into
the provided holes on top of the device.
3. Close the carabiner hooks and check whether the
fastening chains are firmly connected to the carabiner
hooks.
4. Hook the fastening chains into the ceiling holder.
8 EN
radiant heater IR 2000 C / IRS 2010
Assembly of the IRS2010
1. Set the foot(6) up in an upright position.
2. Connect the three component parts of the telescopic
rod(5) with the foot(6) as shown by tightening them.
6
5
3. Connect the plug of the power cable to the socket of the
radiant heater.
ðFix the plug of the power cable.
4. Guide the mains cable from above through the mounted
rod and foot.
5. Place the radiant heater on the tube and fix it
using2screws.
6. Adjust the radiant heater to the desired height and fix the
telescopic rod with twist lock(5).
7. Carefully tilt the device.
EN 9
radiant heater IR 2000 C / IRS 2010
8. Fasten the mains cable to the foot by means of the two
washers and the four screws.
9. Set the device up in an upright and stable position.
Floor fixing (optional)
Fixing the device is usually not necessary, but improves the tilt
stability if the device is intended to be used permanently in one
place.
1. Set the device up in an upright position. Mark the positions
for the fixing holes on the floor through the holes in the
three fixation plates. Observe the minimum distances to
other objects.
2. Drill the holes into the floor at the marked positions.
3. Place the three wedge bolts into the drill holes and screw
down the three fixation plates in place as indicated.
4. Check the foot for tight fit.
Installation
When installing the device, observe the minimum distances
from walls and other objects as described in the Technical data
chapter.
A
B
C
C
D
D
IR 2000 C
IRS 2010
B
D
C
C
D
• Never install the device in a way that it radiates directly
onto walls or other objects. Observe the minimum
distances from walls or other objects according to the
Technical data chapter.
• Do not install the device directly behind a door.
• Please note that the minimum distance to the front also
applies to objects mounted on the ceiling, e.g. fans, lamps
or sprinkler systems.
• Do not attach the device IR2000C directly below a wall
socket.
• Do not position the device IR2010 directly below a wall
socket.
• Set the device IRS2010 up in an upright and stable
position.
10 EN
radiant heater IR 2000 C / IRS 2010
Start-up
Info
Odours might arise upon initial start-up or after a
longer period of non-use.
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• Make sure that there are no curtains or similar objects in
the immediate vicinity.
Prior to initial start-up, insert batteries in the remote control.
Connecting the power cable
• Insert the mains plug into a properly fused mains socket.
Operation
Operating elements
IR 2000 C
8
9
1
IRS 2010
1
8
9
Remote control
10 12
11
No. Designation Meaning
8Segment display Heating level indication:
L1= heating capacity 1000W
L2 = heating capacity 2000W
9Power/Level button Switching the device on or off
Changing the heating level
Switching the LEDelements
on or off
10 Heating level1 button Activate heating power 1000W
(together with heating level2
= 2000W)
11 LED button Switching the LEDelements
on or off
12 Heating level2 button Activate heating power 1000W
(together with heating
level1= 2000W)
This manual suits for next models
1
Table of contents
Other Trotec Electric Heater manuals
Trotec
Trotec DS 20R User manual
Trotec
Trotec IRS 2010 E User manual
Trotec
Trotec TDS 75 User manual
Trotec
Trotec TDE 25 User manual
Trotec
Trotec IR 2010 S User manual
Trotec
Trotec TEH 20T User manual
Trotec
Trotec TEH 200 User manual
Trotec
Trotec IRS 2000 E User manual
Trotec
Trotec TEH 300 User manual
Trotec
Trotec TDS 30 R User manual
Trotec
Trotec TDS 19 E User manual
Trotec
Trotec TDS 30 User manual
Trotec
Trotec IR2001 User manual
Trotec
Trotec TEH 30 T User manual
Trotec
Trotec IRS 2050 E User manual
Trotec
Trotec IRS 800 E User manual
Trotec
Trotec TDS 20 R User manual
Trotec
Trotec TEH 70 User manual
Trotec
Trotec IR 2200 User manual
Trotec
Trotec IR 2050 User manual
