TronicStar 10GPRO-V7-RX-R2 User manual
User Manual
10GPRO-V7-RX-R2
TSCM RF Detector & Receiver
Rev. 26319
TronicStar 10GPRO-V7-RX-R2
2
TronicStar 10GPRO-V7-RX-R2
3
TronicStar 10GPRO-V7-RX-R2 , the most technologically
advanced hand held detector on the market today,
developed by a professional working on spy detectors
for more than 35 years, detect all current spy devices
including the fastest 3G, 4G, 5G digital technology, with
unique differentials of its competitors:
1- Logarithmic detection SiGe technology of laboratory
instruments, intercept ultra-fast digital 3G, 4G, LTE etc.
2- Non-selective detector shows signal level and
demodulated audio at all frequencies, without intervals
or bands, even if a new cellular system comes into
service in the next years, TronicStar 10GPRO-V7-RX-R2
will be able to detect it.
3- Real-time detection unlike other detectors that have
frequency and detection speed limits, the TronicStar
10GPRO-V7-RX-R2 detects in real time all digital or
analog radio frequency spy devices.
4- Detects pulses of 0.8 ns (1200 Mhz) between
frequencies from 1Mhz to over 10Ghz converting pulses
to digitally analyzed signals.
5- Ultra sensitive captures signals from 0.0000001
milliwatt (-70dBm). The most sensitive in the market.
It has a dynamic range of 80dBm.
6- Proprietary firmware that shows the signal strength
separately for analog and digital signals. Special
developed Algorithm to help identify the type of detected
spy device, unlike most detectors that show only the sum
of the signals.
TronicStar 10GPRO-V7-RX-R2
4
TronicStar 10GPRO-V7-RX-R2
5
DESCRIPTION
ON/OFF VOLUME on-off knob and demodulated audio
volume. Always keep it off when replacing battery,
avoiding irreparable damage to the detector by
reversing polarity. Use only alkaline batteries, as
ordinary batteries do not provide sufficient current.
BATTERY LEVEL indicating 8 or 9 for new batteries and
1 for uncharged batteries.
BARGRAPH signal indication system, it is made by bars,
16 lighted bars indicate the highest signal level, around
0dBm.
CLEAN TEST keep this button pressed when turning the
detector on to enter clean test mode. In this state the
detector memorizes and always shows the largest
signal, remaining this state until the detector is turned
off. This mode is also used to find trackers and other
intermitent devices.
INT DETECT while this key is pressed, the same function
described above is performed temporarily like in the
CLEAN TEST mode. Used for checking intermittent
devices that send only one pulse and can go unnoticed in
a conventional sweep. This is the temporary CLEAN
TEST mode.
BEEP ON/OFF turns the beep on and off, when the beep
is on, the letter "B" appears in the display.
TronicStar 10GPRO-V7-RX-R2
6
SPEAKER you can listen to the demodulated audio. AM
and FM conversations are possible to understand, digital
communications are listened like pulsating sounds or
buzzing. It is important to memorize the sounds of
various digital devices during the tests to be identified in
future scans.
ANTENNA CONNECTOR where one of the 3 antennas
included in the kit must be connected by tapping, do not
overtighten, out of use remove and store in the carrying
case to avoid physical damage. Other antennas can be
connected and used with this detector. Input impedance:
50 OHMS and the maximum input power: 10dBM, higher
powers can cause damage to the detector.
PHONE JACK connect stereo or mono headphones. The
jack is stereo with monaural connection, 8 to 32 OHMS
headphones can be used.
DBM LEVEL indication of RF level in dBm, works only in
analog mode.
ANA/DIGI analog / digital mode change key, An or Di
appear on the display indicating the selected operating
mode.
TRIGER POINT key to set beep trigger point. Each time
this key is pressed the point advances one position up to
16. The chosen position coincides with the signal level
required for the beep trigger.
TronicStar 10GPRO-V7-RX-R2
7
ANTENNAS
The signal capture system consists of 3 antennas
designed for different types of spy transmitters and
frequencies:
Low frequency HF and VHF antenna with superior
performance at lower frequencies, blocks high
frequency signals UHF, SHF. It is the antenna used for
basic eavesdropping scans that operate over the
commercial FM range and VHF.
High frequency antenna SHF+ high performance at high
frequencies. Blocks low-frequency signals such as FM
radio stations and reduces interference when
searching for digital devices located at higher
frequencies, cellular devices, WIFI, bluetooth, trackers,
GSM tapping etc. This is the most effective antenna to
find the today ultimate technologies spy devices.
TronicStar 10GPRO-V7-RX-R2
8
Medium frequency UHF and SHF antenna better
performance in frequencies from 800 to 2400 Mhz,
indicated to detect all the spy devices between UHF and
SHF- this antenna has no filter and can be used in
general way or as the initial sweep antenna.
RECEIVING DEMODULATED AUDIO
This model has an audio demodulator to listen to the spy
devices sound on the internal speaker or optional
headphones. Depending on the type of spy device we are
listening, the sound will be audible. AM and FM
conversations are possible to understand, digital
devices will be heard as noises, pulsating sounds or
buzzing.
We encourage users to make as many tests as possible
to familiarize themselves with the demodulated sounds,
for example, make a call next to the detector in GSM and
4G mode, verify the difference in the listened sounds. So
during a sweep when a similar sound is heard, its
identification will be easier.
All local transmitters and spy devices will be received at
the same time, the stronger the signal, the louder the
audio volume.
TronicStar 10GPRO-V7-RX-R2
9
Check the link on the website product page for the
sample audio file sounds emitted by different devices.
The audio receiver is turned on while the detector is on.
The only setting is the audio volume controlled by the
same knob used to turn the detector on and off. To not
listen to the audio, leave the volume knob to a minimum.
DIGITAL / ANALOG MODE
Next to the battery indication level, appears "Di"
indicating that the detector is in digital mode or "An" in
analog mode. Press the analog/digital key to toggle the
operating mode.
TronicStar 10GPRO-V7-RX-R2
10
In analog mode the LCD display preferably shows the
signals from devices such as analog eavesdropping and
analog wireless video cameras. In digital mode, the
display shows the signals of digital devices like GSM
bugs, trackers, cell phones, routers, WIFI cameras etc.
Hi power analog transmitters can interfere with digital
mode detection by having continuous carrier wave
overlapping the digital signals.
CONTINUOUS AND INSTANT MEMORY
By pressing and holding the "MEM" key, the signal
strength shown is frozen at the highest value and the
indication will only be updated if there is an even
stronger signal, the strongest signal will always be
displayed until we stop pressing the key.
In the CLN TEST mode (page 5), the strongest signal
sampling remains until the detector is turned off. This
mode is used for checking a safe room or for discovering
intermittent devices such as vehicle trackers.
We must use CLN TEST to know if the environment
remains clean. After scanning, even if considered safe
room, tests should be performed continuously, since spy
devices may be inert hidden in the room and at any time
start broadcasting. The detector must be continuously
on-site in CLN TEST mode to indicate if any wireless spy
device become active.
Table of contents
