Tripp Lite Smart Series Guide

Thank you for purchasing the Tripp Lite SmartPro

Medical Grade SMART SERIES Tower UPS.

We hope this product exceeds your expectations of

performance in its intended application.

Throughout the life span of this UPS, there are

some maintenance practices that need to occur in

order to ensure continued operation of the unit.

The primary component that requires attention is

the internal battery of the UPS system.

In spite of good maintenance practices and favorable

operating conditions, the capacity of batteries does

deplete over time which reduces the back up or run

time a UPS can deliver to user applications.

Some environmental factors that influence loss of

battery capacity are:

•Humidity

•Temperature

•Depth of discharge

•Frequency of recharge

Replacing the batteries may be required if the UPS has been stored for

an extended period of time without a recharge, a loss of AC power

occurred allowing the batteries to completely discharge, or if a problem

has occurred whereby the batteries cannot sustain an adequate voltage.

For planning purposes, expect most batteries in Tripp Lite UPS products

to have a lifespan of 3-5 years. However, for applications that require

constant discharging and charging of the internal batteries on a daily

basis, the lifespan expectation diminishes at a much higher rate.

Because battery cells have only a finite number of discharge and

recharge cycles, the internal batteries may require replacement within a

2 year period if not earlier. This issue is also magnified by deep

discharges, or complete battery drains, allowing the UPS to completely

power off due to lack of DC voltage.

Providing the UPS with a fresh set of batteries maintains the

effectiveness and reliability of the unit and restores the UPS capacity to

its factory fresh state.

The SMART SERIES comes equipped with a user accessible

battery replacement door, which enables qualified

personnel to replace the UPS’ batteries without the need to

take the unit out of service. This prevents extended

downtimes for an application.

The batteries in the SMART SERIES are hot-swappable,

which allows for the replacement to occur while the

equipment attached to the unit continues to operate.

However, for added safety to the load, consider

performing battery replacement during off or non-peak

hours of your application with the attached load shut

down, and the UPS completely powered off.

The following steps are crucial to proper

battery replacement.

Please adhere to these instructions in order to

prevent personal injury and damage to the

UPS.

Facing the rear of the

UPS, locate the two

screws that hold the

battery door in place.

Using a Phillips head

screw driver, remove

the two screws. Once

the last screw is

removed, remove the

battery door from the

UPS.

Locate the tab made of

black tape that allows the

battery cartridge to be

pulled away from the unit

(indicated by the yellow

arrow).

Firmly grasp the tab and

pull the battery away from

the unit enough to expose

the black battery cable

taped to the battery itself

(indicated by the green

arrow).

Remove the tape

covering the black

battery cable connection

to the battery.

Using needle nose pliers,

pull the cable away from

the battery terminal in a

side to side motion until

the cable is

disconnected.

Using the tab that allows

the battery cartridge to be

removed from the UPS

(indicated by the yellow

arrow), begin to pull the

battery away from the unit.

As more of the battery is

exposed, place one hand

underneath the battery

cartridge (indicated by the

green arrow) to support it

as it is removed from the

unit.

Other Tripp Lite UPS manuals

Tripp Lite

Tripp Lite BC Internet User manual

Tripp Lite

Tripp Lite IO700NAFTA User manual

Tripp Lite

Tripp Lite G1000UB Configuration guide

Tripp Lite

Tripp Lite SM2200RMNAFTA User manual

Tripp Lite

Tripp Lite AVRX550U User manual

Tripp Lite

Tripp Lite OMNI1000LCD User manual

Tripp Lite

Tripp Lite SMART1000LCDU User manual

Tripp Lite

Tripp Lite SmartPro SMART1050SLT User manual

Tripp Lite

Tripp Lite Line-Interactive UPS System SMART750USB User manual

Tripp Lite

Tripp Lite SMART3000RM2UL User manual

Tripp Lite

Tripp Lite SmartPro SMART3000RM2UN Installation guide

Tripp Lite

Tripp Lite HT1500UPS User manual

Tripp Lite

Tripp Lite SmartPro SLT User manual

Tripp Lite

Tripp Lite OmniSmart User manual

Tripp Lite

Tripp Lite SmartOnline SU5000RT4U-IMS User manual

Tripp Lite

Tripp Lite SmartOnline Single-Phase 10kVA User manual

Tripp Lite

Tripp Lite Standby UPS Systems Internet I User manual

Tripp Lite

Tripp Lite OMNIX350HG User manual

Tripp Lite

Tripp Lite OMNIVSINT800 User manual

Tripp Lite

Tripp Lite OmniSmart OMNISMART1050 User manual

Tripp Lite

Tripp Lite OmniSmart OMNISMART500 User manual

Tripp Lite

Tripp Lite ECO1000LCD User manual

Tripp Lite

Tripp Lite TE600 User manual

Tripp Lite

Tripp Lite Internet Office & BC Personal UPS System User manual

Popular UPS manuals by other brands

Pylontech

Pylontech Victron & Pylontech US5000 manual

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 user manual

Mecer

Mecer ME-1000-WTU user manual

Mustek

Mustek PowerMust 530(B) Plus Startup manual

Emerson

Emerson Liebert NXL series Operation and maintenance manual

MAKELSAN

MAKELSAN BOXER SERIES user manual

Block

Block PC-0524-400-0 manual

CyberPower

CyberPower CP585LCD user manual

Eaton

Eaton 3S Advanced user's guide

CyberPower

CyberPower Office Tower Series UPS 1000 user manual

CyberPower

CyberPower BM100 quick start guide

Best Power

Best Power 610 quick start guide

Best Power

Best Power Unity/I UT3K user manual

Mustek

Mustek PowerMust 400 Offline user manual

Xantrex

Xantrex Trace 512 UR-UPS owner's manual

Forza

Forza SL-1501UL user manual

LEGRAND

LEGRAND keor 310081 quick start guide

ABB

ABB Conceptpower DPA 500 operating manual