Triplett POE2000 Pro User manual

POE2000 Pro

PoE Tester

USER MANUAL

Introduction

Thank you for purchasing the Triplett POE200 POE TESTER PRO. Please

read the manual carefully before using the product. This tester helps to speed

up the installation and troubleshooting of PoE systems devices. The Main

Functions of this tester are:

Detecting PSE-type/class, power source, polarity and voltage

Determining-standard PoE or NON-standard passive PoE

Inline Power Level Monitoring

The standard compliance this tester works for are:

IEEE 802.3 af,(PoE)

IEEE 802.3 at (PoE+)

IEEE 802.3 bt (PoE ++)

3www.triplett.com UM-POE2000

Description

RJ45 PSE Test Jack

(2) LED indicators for Power Type Reverse (REV) Polarity

(4) LED indicators for IEEE 802.3 af or IEE802.3 at/bt Standard

LCD Display for Voltage , Current and Power

STEP Button for selecting specific data to be displayed (Default is Voltage)

RJ45 PD Test Jack

4www.triplett.com UM-POE2000

Operation

Note: This tester does not need a battery to operate as it uses system

power when connected to a device.

●Connect to RJ45 PSE Test Jack for PSE type tests (PoE switches, PoE

midspan switches, PoE (Active / Passive) injectors.

●Connect to RJ45 PD Test Jack for PD tests (IP camera, IP phone and

Wireless AP and Other Network Appliances.

●Connect Inline for Inline Power Level Monitoring (Voltage (V), Current

(mA/A), Power (W)

Pressing the STEP Button allows the selection of specific test data for reading.

Display Ledger

Either IEEE 802.3 af

or 802.3 at

compliant standard

and either

Endspan, Midspan

or Ultra-4 pair

Power Source

IEEE 802.3 af - Power

Source End (A)

5www.triplett.com UM-POE2000

IEEE 802.3 at - Power

Source End (A)

IEEE 802.3 af - Power

Source Mid (B)

IEEE 802.3 at - Power

Source Mid (B)

REVERESED Polarity

Power Source either

Endspan, Midspan or

both

6www.triplett.com UM-POE2000

Test Modes

There are (3) Modes of operation for this tester selectable by the switch at the

rear of the tester. The function modes are as follows:

T mode: for detecting PSE status

N mode: for determining NON-standard PoE + inline testing

I mode: for testing and monitoring real time power status

Operation Notes

When performing Inline Testing in T-Mode connect to the PSE side of

the tester first .until voltage is displayed, then connect PD side.

The length of the cable and the quality of the cable or the pin location

in the RJ45 connector can affect the real power available. To ensure

the power at the other end of the wall outlet is what is required for PD

test the wattage level at the wall outlet/jack where the PD plugs in.

The STEP button allows you to select specific test data for easier

reading .Pressing this button once will change auto-rotate to step

mode, and voltage display will be the default measurement. Press the

button again to select current or power display.

To revert back to auto-rotate, disconnect the PSE side cable (If in

Inline Testing disconnect PD side cable first, then disconnect the PSE

Numeric LCD for Inline

Power Testing (U) Voltage,

(A) Current, (P) Power

STEP Button cycles:

Voltage CurrentPower

7www.triplett.com UM-POE2000

side of the cable), Reconnecting the PSE to the tester will start auto-

rotate display.

To perform a reset, first unplug the cable from PD side, next unplug

the PSE side cable. Reconnect the PSE side until voltage values are

displayed then connect to the PD to be tested.

The tester cannot measure and test PD alone, it has to be connected

to a PSE first, Once this is done then connect to the PD, after

negotiation process, the tester will start power

Level testing.

**CAUTION**: Before connecting PD to the tester make sure that

the PD to be connected is either a standard PoE powered device

or a non-PoE powered device to avoid damaging a non-PoE

device is damaged by a non-standard passive PoE power.**

8www.triplett.com UM-POE2000

Specifications

Table of contents

Other Triplett Test Equipment manuals

Triplett

Triplett MG430 User manual

Triplett

Triplett 310-TEL User manual

Triplett

Triplett CTX1200 User manual

Triplett

Triplett EMF20 User manual

Triplett

Triplett CTT47 User manual

Triplett

Triplett Low Voltage Pro 20 User manual

Triplett

Triplett Fox Jr. User manual

Triplett

Triplett PR450 User manual

Triplett

Triplett WiFi Hound User manual

Triplett

Triplett Fox Jr. User manual

Triplett

Triplett CamView IP Pro Series User manual

Triplett

Triplett 310 User manual

Triplett

Triplett CamView5 User manual

Triplett

Triplett CamView IP Pro-X Series User manual

Triplett

Triplett PairMaster 3240-22 User manual

Triplett

Triplett 9310-A User manual

Triplett

Triplett MG420 User manual

Triplett

Triplett LVPro20 User manual

Triplett

Triplett ET550 User manual

Triplett

Triplett 2000 User manual

Triplett

Triplett CamView HD Pro User manual

Triplett

Triplett BR750 User manual

Triplett

Triplett WireMaster Mapper User manual

Triplett

Triplett WireMaster Coax User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual