Trane A5HP4 User manual

88-A5HP4001-1A-EN

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

IMPORTANT – This Document is customer property and is to remain with this unit. Please return to service informa-

tion pack upon completion of work.

These instructions do not cover all variations in systems or provide for every possible contingency to be met in connection with

the installation. Should further information be desired or should particular problems arise which are not covered sufficiently for the

purchaser’s purposes, the matter should be referred to your installing dealer or local distributor.

Note: The manufacturer recommends installing only approved matched indoor and outdoor systems. All of the manufacture’s split

systems are A.H.R.I. rated only with TXV/EEV indoor systems. Some of the benefits of installing approved matched indoor and

outdoor split systems are maximum efficiency, optimum performance and the best overall system reliability.

Table of Contents

Section 1. Safety..................................................................................... 2

Section 2. Unit Location Considerations.............................................. 4

Section 3. Unit Preparation.................................................................... 5

Section 4. Setting the Unit ..................................................................... 5

Section 5. Refrigerant Line Considerations......................................... 6

Section 6. Refrigerant Line Routing ..................................................... 7

Section 7. Refrigerant Line Brazing...................................................... 8

Section 8. Refrigerant Line Leak Check ............................................... 9

Section 9. Evacuation............................................................................. 9

Section 10. Service Valves..................................................................... 9

Section 11. Electrical - Low Voltage ................................................... 10

Section 12. Electrical - High Voltage .................................................. 11

Section 13. Start Up.............................................................................. 12

Section 14. System Charge Adjustment............................................. 12

Section 15. Checkout Procedures....................................................... 16

Section 16. Defrost Control ................................................................. 17

Section 17. Troubleshooting ................................................................ 20

Section 18. Wiring Diagrams ............................................................... 22

Section 19. Pressure Curves ............................................................... 27

Section 20. Refrigerant Circuit (only for reference)........................... 32

Heat Pumps

A5HP4

Installation and Operation Manual

2 88-A5HP4001-1A-EN

Section 1. Safety

WARNING

This information is intended for use by individuals

possessing adequate backgrounds of electrical and

mechanical experience. Any attempt to repair a central

air conditioning product may result in personal injury

and/or property damage. The manufacture or seller

cannot be responsible for the interpretation of this

information, nor can it assume any liability in connec-

tion with its use.

Extreme caution should be exercised when opening

the Liquid Line Service Valve. Turn counterclockwise

until the valve stem just touches the rolled edge. No

torque is required. Failure to follow this warning will

result in abrupt release of system charge and may

result in personal injury and /or property damage.

UNIT CONTAINS R-454B REFRIGERANT!

Proper service equipment is required. Failure to use

proper service tools may result in equipment damage

or personal injury.

SERVICE

USE ONLY R-454B REFRIGERANT AND

APPROVED COMPRESSOR OIL.

WARNING

The appliance is not to be used by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, un-

less they have been given supervision or instruction.

WARNING

Children should be supervised to ensure that they do

not play with the appliance.

WARNING

If using existing refrigerant lines should be brazed not

soldered. Solder alloys with a melting temperature

less than 427°C are not acceptable.

CAUTION

Scroll compressor dome temperatures may be hot. Do

not touch the top of compressor; it may cause minor to

severe burning.

CAUTION

WARNING

WARNING!

This product can expose you to chemicals including lead,

which are known to the State of California to cause cancer

and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov

WARNING

Only qualified personnel should install and service the

equipment. The installation, starting up, and servicing

of heating, ventilating, and air-conditioning equipment

can be hazardous and requires specific knowledge

and training. Improperly installed, adjusted or altered

equipment by an unqualified person could result in

death or serious injury. When working on the equip-

ment, observe all precautions in the literature and on

the tags, stickers, and labels that are attached to the

equipment.

WARNING

RISK OF FIRE!

Flammable refrigerant used. To be repaired only by

trained service personnel. Do not puncture refrigerant

tubing.

Dispose of properly in accordance with federal or local

regulations. Flammable refrigerant used.

Mode Model Operating Range

Cooling 1.5 – 5 Ton 55°F – 120°F

Table 1. Operating Range

Ensure that the area is in the open or that it is

adequately ventilated before breaking into the system

or conducting any hot work.

WARNING

The appliance shall be stored in a room without contin-

uously operating ignition sources (for examples: open

flames, an operating gas appliance or an operating

electric heater). Do no pierce or burn. Be aware that

refrigerants may not contain an odour.

WARNING

LIVE ELECTRICAL COMPONENTS!

During installation, testing, servicing, and trouble-

shooting of this product power should be discon-

nected. It may be necessary to work with live electrical

components. Failure to follow all electrical safety pre-

cautions when exposed to live electrical components

could result in death or serious injury..

88-A5HP4001-1A-EN 3

Section 2. Unit Location Considerations

2.1 Unit Dimensions and Weight

Table 2.1

When mounting the outdoor unit on a roof, be sure the

roof will support the unit’s weight.

Properly selected isolation is recommended to alleviate

sound or vibration transmission to the building

structure.

Unit Dimensions and Weight

Models H x D x W (in)

Weight* (lb)

A5HP4018D 33 X 30 X 33 174

A5HP4024D 33 x 30 x 33 174

A5HP4030D 33 x 30 x 33 174

A5HP4036D 37 x 34 x 37 199

A5HP4042D 45 x 34 x 37 250

A5HP4048D 45 x 34 x 37 250

A5HP4060D 45 x 34 x 37 251

* Weight values are estimated uncrated.

2.3 Refrigerant Piping Limits

1. The maximum TOTAL length of refrigerant lines from outdoor to indoor unit should NOT exceed 150 feet

(including lift).

2. The maximum vertical change should not exceed 50 feet.

3. Service valve connection diameters are shown in Table 5.1.

Note: For other line lengths, refer to Refrigerant Piping Application Guide, SS-APG006F-EN, or Refrigerant

Piping Software Program.

50’

Max

Vertical

Change

50’

Max

Vertical

Change

Standard

Line Set

150’ Max

TOTAL Line Length

2.2 Piping Guidelines

Piping material, pipe routing, and installation shall include protection from physical damage in operation and

service, and be in compliance with national and local codes and standards. All field joints shall be accessible for

inspection prior to being covered or enclosed. Install of pipe work shall be kept to a minimum.

That provisions shall be made for expansion and contraction of long runs of piping.

4 88-A5HP4001-1A-EN

Min. 12” to

Shrubbery

Avoid Install

Near Bedrooms

Min 5’ Unrestricted

Access Panel

Min 3’

Unrestricted

2.4 Suggested Locations for Best Reliability

2.5 Cold Climate Considerations

Ensure the top discharge area is unrestricted for at least

five (5) feet above the unit.

Three (3) feet clearance must be provided in front of the

control box (access panels) and any other side requiring

service.

It is not recommended to install in a location where noise

may distract the building occupants. Some examples

of these types of locations are sleeping quarters and by

windows of a living area. Please discuss location with the

building owner prior to installation.

Avoid locations such as near windows where

condensation and freezing defrost vapor can annoy a

customer.

Position the outdoor unit a minimum of 12” from any wall

or surrounding shrubbery to ensure adequate airflow.

Outdoor unit location must be far enough away from any

structure to prevent excess roof runoff water or icicles

from falling directly on the unit.

NOTE: It is recommended that these precautions be taken for units being installed in areas where snow

accumulation and prolonged below freezing temperatures occur.

• Units should be elevated 3-12 inches above the pad or rooftop, depending on local weather. This additional

height will allow drainage of snow and ice melted during defrost cycle prior to its refreezing. Ensure that drain

holes in unit base pan are not obstructed preventing draining of defrost water.

• If possible, avoid locations that are likely to accumulate snow drifts. If not possible, a snow drift barrier should

be installed around the unit to prevent a build-up of snow on the sides of the unit.

Section 3. Unit Preparation

3.1 Prepare The Unit For Installation

STEP 1 - Check for damage and report promptly to the carrier any damage found to the unit.

Section 4. Setting the Unit

4.1 Pad Installation

When installing the unit on a support pad, such as a concrete slab, consider the following:

• The pad should be at least 1” larger than the unit on all sides.

• The pad must be separate from any structure.

• The pad must be level.

• The pad should be high enough above grade to allow for drainage.

• The pad location must comply with National, State, and Local codes.

88-A5HP4001-1A-EN 5

Line Length

Section 5. Refrigerant Line Considerations

5.1 Refrigerant Line and Service Valve Connection Sizes

Table 5.1

5.3 Required Refrigerant Line Length

5.2 Factory Charge

5.4 Refrigerant Line Insulation

Important: The Vapor Line must always be

insulated. DO NOT allow the Liquid Line and

Vapor Line to come in direct (metal to metal)

contact.

Vapor Line

Liquid Line

Insulation

Determine required line length and lift. You will

need this later in STEP 2 of Section 14.

Total Line Length = __________ Ft.

Total Vertical Change (lift) = __________ Ft.

The outdoor condensing units are factory charged with the system charge required for the outdoor condensing

unit, ten (10) feet of tested connecting line, and the smallest rated indoor evaporative coil match. Always verify

proper system charge via subcooling (TXV/EEV) or superheat (fixed orifice) per the unit nameplate.

Alternate Refrigerant Line and Service Valve Connection Sizes

Line Sizes Service Valve Connection Sizes

Model Vapor

Line

Liquid

Line

Vapor Line

Connection

Liquid Line

Connection

A5HP4018D 5/8 5/16 3/4 5/16

A5HP4024D 3/4 5/16 3/4 5/16

A5HP4030D 3/4 5/16 3/4 5/16

A5HP4036D 3/4 5/16 3/4 5/16

A5HP4042D 7/8 5/16 7/8 5/16

A5HP4048D 7/8 5/16 7/8 5/16

A5HP4060D 7/8 3/8 7/8 3/8

Line Sizes Service Valve Connection Sizes

Model Vapor

Line

Liquid

Line

Vapor Line

Connection

Liquid Line

Connection

A5HP4018D 5/8 3/8 3/4 5/16

A5HP4024D 3/4 3/8 3/4 5/16

A5HP4030D 3/4 3/8 3/4 5/16

A5HP4036D 3/4 3/8 3/4 5/16

A5HP4042D 7/8 3/8 7/8 5/16

A5HP4048D 7/8 3/8 7/8 5/16

A5HP4060D 7/8 3/8 7/8 3/8

6 88-A5HP4001-1A-EN

5.5 Reuse Existing Refrigerant Lines

For retrofit applications, where the existing indoor evaporator coil and/or refrigerant lines will be used, the following

precautions should be taken:

• Ensure that the indoor evaporator coil and refrigerant lines are the correct size.

• Ensure that the refrigerant lines are free of leaks, acid, and oil.

CAUTION

If using existing refrigerant lines make certain that all joints are brazed, not soldered.

Section 6. Refrigerant Line Routing

6.1 Precautions

Important: Take precautions to prevent noise

within the building structure due to vibration

transmission from the refrigerant lines.

For Example:

• When the refrigerant lines have to be fastened to floor joists or other framing in a structure, use isolation type

hangers.

• Isolation hangers should also be used when refrigerant lines are run in stud spaces or enclosed ceilings.

• Where the refrigerant lines run through a wall or sill, they should be insulated and isolated.

• Isolate the lines from all ductwork.

• Minimize the number of 90º turns.

Comply with National, State, and Local Codes when

isolating line sets from joists, rafters, walls, or other

structural elements.

Isolation From Joist/Rafter

Side View

8 Feet Maximum

Secure Vapor line from joists using isolators every 8 ft. Secure

Liquid Line directly to Vapor line using tape, wire, or other appro-

priate method every 8 ft.

Joist/Rafter

Isolator

Line Set

8 Feet Maximum

Isolation In Wall Spaces

Side View

Wall

Isolator

Line Set

8 Feet Maximum

Secure Vapor Line using isolators every 8 ft. Secure Liquid Line

directly to Vapor Line using tape, wire, or other appropriate

method every 8 ft.

8 Feet Maximum

88-A5HP4001-1A-EN 7

Isolation Through Wall DO NOT hang line sets from ductwork

Sealant

Insulation

Vapor Line

Wall

Ductwork

Isolator

Line Set

Section 7. Refrigerant Line Brazing

7.1 Braze The Refrigerant Lines

STEP 1 - Remove caps or plugs. Use a deburing tool to debur the pipe ends. Clean both internal and external

surfaces of the tubing using an emery cloth.

STEP 2 - Remove the pressure tap cap and valve cores from both service valves.

STEP 3 - Purge the refrigerant lines and indoor coil with dry nitrogen.

Purge the refrigerant lines and indoor coil with dry nitrogen.

Note: A2L equipment shall have red marked service ports and pipes through which refrigerant is serviced.

STEP 4 - Wrap a wet rag around the valve body to avoid heat damage and continue the dry nitrogen purge.

Braze the refrigerant lines to the service valves.

For units shipped with a field-installed external drier, check liquid line filter drier’s directional flow arrow to confirm

correct direction of refrigeration flow (away from outdoor unit and toward evaporator coil) as illustrated. Braze the

filter drier to the Liquid Line.

Continue the dry nitrogen purge. Do not remove the wet rag until all brazing is completed.

Important: Remove the wet rag before stopping the dry nitrogen purge.

Note: Install drier in Liquid Line.

NOTE:

Precautions should be taken to avoid heat damage to basepan during brazing. It is recommended to

keep the flame directly off of the basep

an.

STEP 5 - Replace the pressure tap valve cores and plastic tabs after the service valves have cooled.

STEP 1 STEP 2 STEP 3

8 88-A5HP4001-1A-EN

3-4” from valve

STEP 4 STEP 5

Section 8. Refrigerant Line Leak Check

8.1 Check For Leaks

STEP 1 - Pressurize the refrigerant lines and evaporator coil to 150 PSIG using dry nitrogen.

STEP 2 - Check for leaks by using a soapy solution or bubbles at each brazed location.

Note: Remove nitrogen pressure and repair any leaks before continuing.

STEP 3 - Once the initial leak check is complete, complete a system pressure test. Pressurize the system to the

design pressure of the system for a minimum of 60 minutes. Do not add additional refrigerant or test gas after

reaching the design pressure. The system should show no loss of pressure once pressurized. Once the pressure

test is complete follow the steps for evacuation.

After completion of field piping for split systems, the field pipework shall be pressure tested with nitrogen and then

vacuum tested prior to refrigerant charging, according to the following requirements:

1. The minimum leak test pressure of the lineset and indoor coil shall be the high side design pressure, unless the

high side of the system, cannot be isolated from the low side of the system in which case the entire system

shall be pressure tested to the low side design pressure.

2. The test pressure after removal of pressure source shall be maintained for at least 1 hour with no decrease of

pressure indicated by the test gauge, with test gauge resolution not exceeding 5% of the test pressure.

Important: Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks.

Important: The following leak detection methods are deemed acceptable for all refrigerant systems:

• Electronic leak detectors calibrated for R454B

• Bubble method

STEP 2 - Observe the micron gauge. Evacuation

is complete, if the micron gauge does not rise

above 500 microns in one (1) minute and 1500

microns in ten (10) minutes.

STEP 3 - Once evacuation is complete, blank off

the vacuum pump and micron gauge, and close

the valve on the manifold gauge set.

1 MIN.

Important: Do not open the service valves until

the refrigerant lines and indoor coil leak check

and evacuation are complete.

STEP 1 - Evacuate until the micron gauge reads

no higher than 350 microns, then close off the

valve to the vacuum pump.

0350

Microns

ON OFF

Section 9. Evacuation and Servicing

9.1 Evacuate the Refrigerant Lines and Indoor Coil

88-A5HP4001-1A-EN 9

Section 10. Service Valves

10.1 Open the Gas Service Valve

Important: Leak check and evacuation must be completed before opening the service valves.

NOTE: Do not vent refrigerant gases into the atmosphere.

STEP 1 - Remove valve stem cap.

STEP 2 - Using an adjustable wrench, turn valve stem 1/4 turn counterclockwise to the fully open position.

STEP 3 - Replace the valve stem cap to prevent leaks. Tighten finger tight plus an additional 1/6 turn.

10.2 Open the Liquid Service Valve

Important: Leak check and evacuation must be completed before opening the service valves.

STEP 1 - Remove service valve cap.

STEP 2 - Fully insert 3/16” hex wrench into the stem and back out counterclockwise until valve stem just touches

the rolled edge (approximately five (5) turns.)

STEP 3 - Replace the valve cap to prevent leaks. Tighten finger tight plus an additional 1/6 turn.

Extreme caution should be exercised when opening the Liquid Line Service Valve. Turn counterclockwise until

the valve stem just touches the rolled edge. No torque is required. Failure to follow this warning will result in

abrupt release of system charge and may result in personal injury and /or property damage.

WARNING

9.2 Servicing

Under no circumstances shall potential sources of ignotion be used in the searching for or detection of refrigerant

leaks.

The following leak detection methods are deemed acceptable for all refrigerant systems:

• Electronic leak detectors calibrated for R454B

• Bubble method

• Fluorscent method agents

If a leakage of refirgerant is found which requires brazing, all of the refrigerant shall be recovered from the system,

or isolated (by means of shut off valves) in a part of the system remote from the leak.

• If repairs must be made after system is charged, properly and safely remove or isolate refrigerant and purge

the section of the system needing repair with Nitrogen gas or oxygen free nitrogen prior to opening the circuit.

• The REFRIGERANT CHARGE shall be recovered into the correctly marked recovery cylinders.

• Ensure that the outlet for the vaccum pump is not close to any potential ignition sources and the ventilation is

available.

• Prior to recharging the system, it shall be pressure-tested with the appropriate purging gas. The system shall

be leak-tested on completion of charging but prior to commissioning. A follow up leak test shall be carried out

prior to leaving the site.

• Ensure that only appropriate refrigerant recovery cylinders are employed. Ensure that the correct number of

cylinders for holding the total system charge is available. Only use cylinders designated for the recovered

refrigerant and labelled for the refrigerant. Cylinders shall be complete with pressure-relief valve and

associated shut-off valves in good working order.

• A set of caliberated weighing scales shall be available and in good working order. Hoses shall be complete

with leak-free disconnect couplings and in good condition. Ensure any associated electrical components are

sealed.

• The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder. Do not

mix refrigerants.

• If compressors or compressor oils are to be removed, ensure that they have been evacuated to an

acceptable level to make certain that FLAMMABLE REFRIGERANT does not remain within the lubricant.

10 88-A5HP4001-1A-EN

Section 11. Electrical - Low Voltage

11.1 Low Voltage Maximum Wire Length

Table 11.1 defines the maximum total length of

low voltage wiring from the outdoor unit, to the

indoor unit, and to the thermostat.

Table 11.1

24 VOLTS

WIRE SIZE MAX. WIRE LENGTH

18 AWG 150 Ft.

16 AWG 225 Ft.

14 AWG 300 Ft.

11.2 Low Voltage Hook-up Diagrams

CAP

1/4 TURN ONLY

COUNTERCLOCKWISE

FOR FULL OPEN

POSITION

VALVE STEM

GAS LINE CONNECTION

UNIT SIDE

OF VALVE

PRESSURE TAP PORT

Cap

Rolled Edge to

Captivate Stem

Hex Headed

Valve System

Service Port

3/16” Hex Wrench

Unit Side of

Service Valve

Gas Service Valve Liquid Service Valve

• The approved ID/OD combination will provide sufficient safe ventilation in case of a leak.

• Refer Indoor Unit Installer’s Guide for correct specifications on indoor unit install.

• All systems require mitigation boards so on altitude adjustment factors required.

• MCB neds to be included in an A2L System.

Mitigation Board Guidelines

With A5AH4With A5AH6 With 5TAM5

1. Units with pigtails require wirenuts for connections.

2. Cap all unused wires.

3. In AC systems, for multiple stages of electric heat,

jumper W1 and W2 together if comfort control has

only one stage of heat.

1. Units with pigtails require wirenuts for connections.

2. Cap all unused wires.

3. In AC systems for multiple stages of electric heat,

jumper W1 and W2 together if comfort control has

only one stage of heat.

1. Units with pigtails require wirenuts for connec-

tions.

2. Cap all unused wires.

3. When BK is used, do not connect Y2 at the air

handler.

4. When BK is used, cut the jumper between R and

BK on the control board. See indoor wiring

schematic for details.

5. In AC systems, for multiple stages of electric heat,

jumper W1 and W2 together if comfort control has

only one stage of heat.

Thermostat Air Handler Outdoor

Unit

Thermostat Air Handler Outdoor

Unit Thermostat Air Handler Outdoor

Unit

B/C

Blue

24 VAC HOT

FAN

24 VAC

Common

COOL/HEAT

1st STAGE

HEATING

1st STAGE

HEATING

2nd STAGE

HEATING

3rd STAGE

Pink

White

OO O

YOY

Brown

B/C

Blue

24 VAC HOT

FAN

24 VAC

Common

COOL/HEAT

1st STAGE

HEATING

1st STAGE

HEATING

2nd STAGE Pink

White

OO O

YOY

B/C

Blue

24 VAC HOT

FAN

24 VAC

Common

COOL/HEAT

1st STAGE

HEATING

1st STAGE

HEATING

2nd STAGE Pink

White

OO O

YOY

WH/BLK

This manual suits for next models

Table of contents

Other Trane Heat Pump manuals

Trane

Trane 2TWB0012-036AA Assembly instructions

Trane

Trane 4TTX5018-060 User manual

Trane

Trane 5TTR4018A User manual

Trane

Trane WEATHERTRON 4TWX6 Assembly instructions

Trane

Trane WC*150B***G Series Owner's manual

Trane

Trane 4WCC4024E1000A User manual

Trane

Trane WSC060-120 User manual

Trane

Trane WCY024G1 Instruction manual

Trane

Trane Axiom GEHB Owner's manual

Trane

Trane A4AC4018B1000A Assembly instructions

Trane

Trane Ultra-Low NOx Series Assembly instructions

Trane

Trane WFS-IR 1 Quick start guide

Trane

Trane 2TTA0030AD000A Assembly instructions

Trane

Trane WCK024B1 Owner's manual

Trane

Trane Axiom GWS Series Installation and operating instructions

Trane

Trane 2TTR2018-060 Assembly instructions

Trane

Trane Axiom EXHF006 Installation and operating instructions

Trane

Trane TTK 509 E User manual

Trane

Trane 5TTR5018 User manual

Trane

Trane XL Series Weathertron Installation instructions

Trane

Trane 4TWR3 Assembly instructions

Trane

Trane 4WCY5024A1000A Assembly instructions

Trane

Trane 5TWR5 User manual

Trane

Trane 4TTR4018N User manual

Popular Heat Pump manuals by other brands

MICROWELL

MICROWELL HP 1000 GREEN Installation and user manual

Sanyo

Sanyo SAP120FCH Service manual

Daikin

Daikin EHYHBH05AA Operation manual

Panasonic

Panasonic WH-SDF03E3E5 Design handbook

Bryant

Bryant 544B Specifications

Airxcel

Airxcel 45000 Series Installation, operation and maintenance instructions

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Service manual

Dimplex

Dimplex LI 16I-TUR Installation and operating instruction

Carrier

Carrier WSHP Open v3 Integration guide

TGM

TGM CTV14CN018A Technical manual

Carrier

Carrier 38MGQ Series installation instructions

Kokido

Kokido K2O K880BX/EU Owner's manual & installation guide

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Installation and service instructions

Carrier

Carrier 48EZN installation instructions

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Installation and service instructions for contractors

Ariston

Ariston NIMBUS user manual

Weishaupt

Weishaupt WWP L 7 Installation and operating instruction

GE Zoneline AZ85H09EAC datasheet