TRAK RACER FS3 User manual

FS3

Assembly Instructions

Important: Once assembled, please ensure before use that

all screws have been installed correctly and tightened for

safety and stability.

Step 4

Position the pedal plate into the frame and add the screws

according to your preferred position. Note. To adjust the

pedal angle simply loosen the screws by around 2mm, re-

position then tighten.

Step 1

Please use the inner hexagon spanner to remove the 4

screws from the FS3 base.

Step 2

Adjust the lower upright arms to your preferred angle

then re-insert the screws and tighten. This can be

adjusted later for added comfort.

Step 3

Use the inner spanner to remove the 4 screws from the

pedal plate.

Step 5

Attach the Trak Racer branded center inserts of the

frame to the lower upright arms at the front with the holes

facing inwards as below.

Step 10

To mount the shift mount to the left or right side, remove

the 4 screws screws from the frame on your preferred side.

Step 9

Adjust the wheel mount to the preferred height and position

by adding 2 screws back into the frame then tighten. Use

the inner hexagon spanner to affix 8 screws from the rear of

the stand. Place the wheel support bracket onto the front of

the stand and add the 8 nuts and tighten. Adjust the angle

and slide to your preferred location.

Step 11

Position the shift mount, insert screws and tighten using

the 4 screws that were removed in Step 10.

Step 7

Position and affix the top part of the frame to the lower

legs of Step 5 and Step 6. There are two holes with pre-

installed screws in the center of the top frame which

should face to the rear of the stand. Adjust the stand to

your preferred height and tighten the screws to lock the

height.

Step 6

Use the inner hexagon spanner to remove the 2 screws

from the rear legs. Adjust to your preferred angle and

tighten the screws. Insert the rear legs into the non-Trak

Racer center inserts then add screws.

Step 8

Use the inner hexagon spanner to remove the 2 screws

from the center of top frame. These screws are used to

adjust the wheel mount height.

Table of contents

Other TRAK RACER Rack & Stand manuals

TRAK RACER

TRAK RACER TM-B4-27 User manual

TRAK RACER

TRAK RACER TR80-4M4-BLK User manual

TRAK RACER

TRAK RACER MS-FM-SIN User manual

TRAK RACER

TRAK RACER MS-FM-QD User manual

TRAK RACER

TRAK RACER MS-SML-FM User manual

TRAK RACER

TRAK RACER TR160 User manual

TRAK RACER

TRAK RACER TR8 User manual

TRAK RACER

TRAK RACER MS-CM-SML2 User manual

TRAK RACER

TRAK RACER TR80-TMARM4-BLK User manual

TRAK RACER

TRAK RACER TR-TR8-M User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 