TPL VISION M-EBAR User manual

Preamble

rISk claSS

The applicable Standard EN-62471 classies LED Lighting into 4 classes according to their degree of hazard severity.

The table below summarises the risks associated with our standard products.

Colour Class Risk

White WHI, Red 630 nm 0none

IR 850 nm 1low

TPL Vision can provide guidance notes to minimise photo-biological risks, including the nominal minimum

operating distance. Please contact TPL Vision through your usual representative for this information.

In all cases, TPL Vision recommends the use of the protection glasses that are listed in its catalog.

USer gUIde

This Technical User Guide contains warnings and guidance for correct and safe operation of the product.

These instructions must be followed at all times. TPL Vision will not be held responsible for problems caused

by using the product contrary to these instructions and the Warranty will be deemed invalid.

UnPackIng

This product is packed at the factory using suitable materials for safe transport. To open thepackage, do not use

any cutting blade to avoid damaging the product(s). Please use the delivered accessories ifneeded. (Donot use any

other products or equivalents to replace the delivered accessories).

In the event of damage occurring during shipping, it must be reported to the carrier at time of delivery (including

noting the damage in writing on the delivery documents). It is also your responsibility to notify TPL Vision in writing

of the damage within 24 hours of receipt of the package. If these instructions are not followed, TPL Vision reserves

the right not to accept requests for return and exchange of damaged products.

* Total length, without connector.

dImenSIonS

Length

(mm)

Height

(mm)

Width

(mm)

A B C

M-EBAR 125 158 45 47.6

M-EBAR 250 283 45 47.6

M-EBAR 375 408 45 47.6

M-EBAR 500 533 45 47.6

USer gUIde P2/8

nLength (Lg) <500 mm: 2captive nuts M4

n500 mm ≤ Lg <1000 mm: 4captive nuts M4

n1000 mm ≤ Lg ≤ 1250 mm: 6captive nuts M4

fIxIng

(supplied)

Captive nuts Screw M4 (not supplied)

During the set up, the light has to be switched off and unplugged. Please

use M4 screws and insert them in thecaptive nuts located in the back of

the light. The light will be better fixed if you spread the attachment points

symmetrically along the bar.

You can also use M4 screws (not

supplied) fastened directly into

Aluminium profile with a tightening

torque from 0.5 to 1.5Nm. Wealso

recommend the use of a thread-

locker (not supplied) to avoid any

risk of loosening.

Please use all the captive nuts. NEVER REMOVE THEM FROM THE BAR.

led IndIcatorS

: Strobe LED indicator

: Power LED indicator

connectIon

WIrIng

M12 Connector

5 male points

+ 24 V

Ground

PNP

5Dim 0-10V

STROBE PNP

+ 24 V

NPN

Ground

STROBE NPN

+ 24 V

Ground

PNP

+ 24 V

NPN

Ground

CONTINUOUS MODE :

+ 24 V

3GND

5DIM 0-10V

STROBE

NPN

STROBE

PNP 5Dim 0-10V

5Dim 0-10V 5Dim 0-10V

black

brown

blue

grey

white

Front view Top view

P3/8

USer gUIde P4/8

VOLTAGE DROP

Dimensions 125 250 375 500

Max voltage drop in the bar (V) 0.01 0.03 0.06 0.12

Power supply cable : 4x1,5² max length

for acceptable voltage drop (m)* >150

* For longer power supply cable, increase the section of the copper wire.

control

The product is optimised for a lifespan >50kh in a 40°C (104°F) atmosphere.

In strobe mode, the strobing time is directly equivalent to the time during which the strobe entry is activated.

Strobe PnP & nPn

PNP : from 5 to 24V for 100% ON. From 0 to 1V for 100% OFF.

NPN : less than 1V for 100% ON. Above 2V for 100% OFF. Max 20V.

Brightness D max t max f max

100% N/A CW N/A

100% to 240% 1/5 30 ms 30Hz

D : Duty Cycle

t : pulse duration

f : frequency

oPeratIng condItIonS

-10° to +40°C (14° to +104°F) / 80% of humidity without condensation.

No thermal shock (max temperature variation: 10°C (18°F) in 24h).

Not for outdoor use.

P5/8

contInUoUS oPeratIon Strobe oPeratIon

dImmIng 0-10V – Strobe oPeratIon

100%

240%

0 2 4 6 8 10

VOLTS

Potential dimming between

0 & 10 V.

At 0 Volts, the product reaches

240% of its lighting power. Only

usable in the Strobe mode.

Please consider a tolerance of ±5%

when measuring the dimmed bri-

ghtness levels.

STROBE

INPUT

STROBE

INPUT

STROBE

INPUT

30 ms 30 ms

< 30 ms

15 µs 15 µs

LIGHT

Triggering input

>30 ms

240%

100%

< 30 ms

15 µs 15 µs

LIGHT

Triggering input

<30 ms

> 30 ms

15 µs 15 µs

LIGHT

Triggering input

>30 ms

100%

After 30ms, LED are supplied at 100% level.

LED are supplied with 240% maximum

current. After 30ms, LED are supplied

at 100% level.

125 250 375 500

Consumption CW mode 0.3A 0.6A 0.9A 1.2A

Consumption Strobe mode* 1.2A 2.4A 3.6A 4.8A

Min. functioning Voltage 20V in the light input

Normal functioning Voltage 24V in the light input (±10%)

Max. functioning Voltage 30V in the light input

Max. consumption Strobe signal 5mA

*strobed with 20% duty cycle.

PoWer SUPPly

USer Safety

Do not modify or dismantle all or part of the product.

Respect the power supply voltages and the connection terminals.

Ensure power supply is switched off whilst connecting product and turn on only once product

is fully connected. Failure to do this may damage the product and invalidate the Warranty

Do not stare at the lighting source directly.

Follow advice below for installation to minimise operator exposure to the light source.

INSTALLATION GUIDANCE:

• Forbid or limit the direct access to the lighting source (exposure into the radiation axis).

• Establish a security perimeter to prevent the operators from approaching the lighting source beyond therecom-

mendations of the manufacturer.

• If the workstation permits it, introduce a lter that will stop the lighting radiation under a xed or adjustable

frame between the source and the operator. When these measures cannot be implemented, supply the ope-

rators with glasses (class 4) available from TPL Vision, or with a dedicated protective mask, that will stop

thelighting radiation.

It is the responsibility of the persons installing this product to ensure that all means possible (such as those stated

above) have been implemented to reduce exposure of the machine operators to the light emitted from this product.

USer gUIde P6/8

eqUIPment maIntenance

CLEANING (when the product is switched off)

Please use a soft and dry cloth. Do not use any abrasive material.

Do not use any cleaning solvent or aggressive chemical product.

TPL Vision recommends to use isopropyl alcohol.

P7/8

www.tpl-vision.com

TPL VISION

IS AN ISO9001

CERTIFIED MANUFACTURER

+44 (0)1738 310 392 contact@tpl-vision.co.uk

Brenchley House, School Road

Charing, Kent TN27 0JW

United Kingdom

Features and presentations liable to changes without notice. Ref.UG-010801-E2, 2021/10 edition.

Table of contents

Other TPL VISION Lighting Equipment manuals

TPL VISION

TPL VISION TRING User manual

TPL VISION

TPL VISION Modular Ringlight Operation and maintenance manual

TPL VISION

TPL VISION LITE LBAR+ Series User manual

TPL VISION

TPL VISION MEDIUM MBACK User manual

TPL VISION

TPL VISION Ring 80 Manual

TPL VISION

TPL VISION SDOME II 130 User manual

TPL VISION

TPL VISION SQUARE LIGHT RGB User manual

TPL VISION

TPL VISION BLBAR+ User manual

TPL VISION

TPL VISION THINLED 1 User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions