TP-Link Auranet EAP110 User manual
Installation Guide
Wireless N Access Point
EAP110/EAP120/EAP220
CONTENTS
About This Installation Guide
This guide is designed to familiarize you with the general layout of the EAP110,
EAP120 and EAP220, describe how to perform the hardware installation, and how
to configure the EAP Controller software in your network. Your EAP has more
features and functionalities which can be found in the User Guide.
Conventions
Unless otherwise noted, the EAP or the device mentioned in this guide stands for
300Mbps Wireless N Access Point EAP110, Wireless N Gigabit Access Point EAP120
and EAP220.
Network Topology ————————————————————— 01
Hardware Overview ———————————————————— 02
Hardware Installation ——————————————————— 05
1. Installation Requirements ....................................................... 05
2. Mounting Bracket ................................................................... 05
3. Installation ............................................................................ 06
4. Power Supply......................................................................... 11
Software Conguration —————————————————— 13
Q&A ——————————————————————————— 14
Specications ——————————————————————— 15
01
Network Topology
A typical network topology for the EAP is shown below.
Controller Host
02
Hardware Overview
1. LED
EAP110, EAP120 and EAP220 have the same LED status and corresponding
indications.
System LED
LED Status Indication
Solid green The device is working properly.
Flashing red System errors. RAM, Flash, Ethernet, WLAN or
firmware may be malfunctioning.
Flashing yellow Firmware update is in progress. Do not disconnect
or power off the device.
Double-flashing red, green, yellow The device is being reset to its factory default
settings.
03
2. Interface Panel
■EAP110
ARROW 1
RESET ETHERNET
■EAP120/EAP220
ARROW 1
RESET CONSOLE ETHERNET ON/OFF POWER
Please note that EAP110 does not have the CONSOLE port, POWER port or ON/OFF
button. The interface panel components of the EAP, from left to right, are described
in the following list.
Kensington Security Slot
Secure the lock (not provided) into the security slot to prevent the device from
being stolen.
RESET
With the device powered on, press and hold the RESET button for about 8 seconds
until the LED ashes red, then release the button. The device will restore to factory
default settings.
CONSOLE
This port is used to connect to the serial port of a computer or a terminal to check
and monitor system information of EAP120/EAP220.
Note: CLI commands are not available in current software version. We will release
a new version supporting CLI commands soon. Please pay close attention to our
ofcial website.
04
ON/OFF
Press this button to turn on/off the EAP120/EAP220.
POWER
The power port is used to connect the EAP120/EAP220 to an electrical wall outlet
via power adapter. Please only use the provided power adapter. Refer to next
chapter 4.Power Supply to learn how to power the EAP120/EAP220 via power
adapter.
ARROW 1
This arrow is used to align with ARROW 2 on the mounting bracket to lock the EAP
into place. Please refer to next chapter 2.Mounting Bracket to locate ARROW 2.
ETHERNET
For EAP110, this port is used to connect to the POE port of the provided PoE
adapter for both data transmission and power supply through Ethernet cabling.
For EAP120/EAP220, this port is used to connect to a router or a switch to transmit
data or to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data
transmission and Power over Ethernet (PoE) through Ethernet cabling.
■Passive PoE Adapter
The PoE adapter is ONLY provided with EAP110 for power supply. Refer to next
chapter 4.Power Supply to learn more about power supply for EAP110.
Power LED
Power LED
The Power LED indicates the status of the electric current: green (0-0.8A), red
(0.8A-1A).
POE Port
This port is used to connect to the ETHERNET port of EAP110.
LAN Port
This port is used to connect to your LAN.
05
Hardware Installation
The EAP can be wall-mounted or ceiling-mounted. Please suitably arrange your
wire layout before mounting the EAP. We take EAP110 as example to explain the
installation. EAP110 can be powered via the provided PoE adapter, while EAP120
and EAP220 can be powered via a PoE switch or the provided power adapter.
1. Installation Requirements
Before installation, check the package contents for the following items:
Other installation equipments may require, including a pencil, ruler, drill, drill bit,
screwdriver and a ladder.
2. Mounting Bracket
The following figure describes the layout of the mounting bracket.
Locking clip
ARROW 2 is used to align
with ARROW 1 under the
interface panel
Ceiling mounting slot
Wall mounting slot
EAP Mounting Bracket Installation Guide
Wing Nuts (3) Washers (3) Plastic Wall
Anchors (3)
Self-tapping
Screws (3)
Pan-head
Screws (3)
06
3. Installation
■Ceiling Mounting
Note:
■Make sure the thickness of the ceiling is less than 18mm and
the ceiling can bear at least five kilograms.
■It is NOT recommended to mount the EAP on a low-strength
material, such as gypsum ceiling panel. If no other choice is
available, make sure you add a piece of strong material under
the wing nuts to ensure the EAP is mounted solidly.
1. Remove the ceiling tile.
2. Place the mounting bracket in the center of the ceiling tile. Mark the positions
of the three mounting slots and a hole for the Ethernet cable to feed through.
L≈40mm
L
Mark of the hole for Ethernet
cable to feed through
07
3. Use a drill with the appropriate size drill bit to drill three 4mm holes for
the pan-head screws, and drill a 10mm hole for the Ethernet cable to feed
through.
10mm hole for Ethernet cable feed
4mm hole for mounting bracket
4. Secure the mounting bracket to the ceiling tile using the pan-head screws,
washers and wing nuts, as shown below.
Hole to feed the Ethernet cable
Hole to feed the screw
Pan-head screw
Wing nut
Washer
Other manuals for Auranet EAP110
13
This manual suits for next models
2
Table of contents
Other TP-Link Wireless Access Point manuals
TP-Link
TP-Link TL-WA801ND User manual
TP-Link
TP-Link Omada EAP610 User manual
TP-Link
TP-Link Omada EAP615 User manual
TP-Link
TP-Link Omada EAP225-Wall User manual
TP-Link
TP-Link TL-WA701ND User manual
TP-Link
TP-Link Auranet EAP120 User manual
TP-Link
TP-Link TL-WA801ND User manual
TP-Link
TP-Link CPE605 User manual
TP-Link
TP-Link Pharos CPE220 User manual
TP-Link
TP-Link Omada EAP773 User manual
TP-Link
TP-Link 54Mbps Wireless Access Point TL-WA501G User manual
TP-Link
TP-Link TL-WA901ND User manual
TP-Link
TP-Link Auranet EAP110 User manual
TP-Link
TP-Link PHAROS SERIES User manual
TP-Link
TP-Link Omada EAP225-Wall User manual
TP-Link
TP-Link AP300 User manual
TP-Link
TP-Link Omada EAP620 HD V2 User manual
TP-Link
TP-Link Auranet EAP330 User manual
TP-Link
TP-Link Omada EAP615-Wall V1 User manual
TP-Link
TP-Link TL-WA7510N User manual
