Toyotomi FF-95 User manual

FF-95(Type C)

GB OPERATING MANUAL ........................................................................................... PAGE 1

DE GEBRAUCHSANWEISUNG ................................................................................... PAGE 17

FR MANUAL D’UTILISATION ...................................................................................... PAGE 33

NL GEBRUIKSAANWIJZING ....................................................................................... PAGE 49

ENGLISH

IMPORTANT

1) READ AND UNDERSTAND INSTRUCTIONS BEFORE INSTALLING OR USING HEATER.

2) RETAIN INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE.

3) CHECK LOCAL AUTHORITY & BUILDING CODES FOR INSTALLATION REQUIREMENTS.

SECTION A:

SPECIFICATIONS

Model: FF-95

Heater Efﬁciency: 92.4% (1)

Heat Rating: High - 9.50 kW (32,400 BTU/h)

Med - 5.49 kW (18,700 BTU/h)

Low - 2.96 kW (10,100 BTU/h)

Fuel Consumption: High - 1.07 L/h

Med - 0.620 L/h

Low - 0.334 L/h

Fuel System: External tank (2)

Fuel Type: Parafﬁn only

Dimensions (W × H × D): 760 × 700 × 427 mm

Weight: 34 kg

Vent Pipe Hole: 70 ~ 80 mm diameter

Maximum Length of Vent Pipe System: 3 m, 3 bends or less (Section I “Installation”)

Electrical Rating: 230 Volts AC, 50 Hz

(220 Volts AC, 50/60 Hz) (3)

Preheat - MAX 280 W

Burning - MAX 52 W

(1) Heat and vaporized water are produced by fuel combustion. Heat rating does not account for heat loss due to

condensation of water vapor.

(2) External tank to be purchased separately. (Consult your supplier for options.)

(3) It is excluded from CE marking.

SAFETY FEATURES

Your heater is equipped with a number of integral safety features.

Please familiarize yourself with these features. If the heater shuts

down due to the operation of any safety device, ensure the problem

is identified and corrected. Note that normal combustion flames

inside the combustion chamber, can be seen through some “peep

holes”, located in the front bottom left hand corner of the hot air

outlet louvers.

1. Flame Sensor

Heater will automatically stop all operations if ignition fails or if ﬂame fails during combustion, in order to prevent

fuel overﬂow. Error code will be displayed on the digital indicator.

2. Fuel Strainer

Special strainer catches any dirt or impurities present in the fuel before it is sent to the burner.

3. Overheat Protector

Automatically stops all operations if heater cabinet reaches abnormally high temperature due to motor malfunc-

tion or abnormal combustion.

4. Power Failure Recovery System

If power fails during heater operation, heater will turn off. When power resumes, heater will automatically reignite

to maintain the selected room temperature.

NOTE: The operation varies depending on the time length of power failure and other conditions.

Please see Section E “Operation” for more details.

5. Fully Vented System

Flue Pipe system provides outside air for combustion and vents all combustion products to outdoors.

Heat shield plate Overheat protector

Heat exchanger

Fuel pipe

Circulation fan

Burner

Igniter

Burner ring

Flame sensor

Peep hole

Heat chamber

Adjustable leg Blower motor

Fuel sump

Drip tray

Fuel pump

Red Reset button

Integral fuel

strainer (inside)

ENGLISH

SECTION B:

SAFETY TIPS FOR OPERATION

CAUTION: Heater and vent pipe system must be properly installed before operation.

Please follow instructions under “Installation”, Section I.

1. NEVER use any fuel other than Parafﬁn. NEVER USE GASOLINE. Use of gasoline can lead to uncontrollable

ﬂames, resulting in destructive ﬁre.

2. Due to high surface temperatures, keep heater away from children, furniture and clothing while in operation. (See

Installation manual.)

• The appliance is not to be used by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been give supervision or instruction.

• Children being supervised not to play with the appliance.

• This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experiance and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved.

• Children shall not play with the appliance.

•

Cleaning and user maintenance shall not be made by children without supervision.

3. To prevent abnormal operation and prolong heater life, be sure to perform routine maintenance. (See Section F

“Routine maintenance”.)

4. NEVER store or transport fuel in other than a metal or plastic container that is acceptable for fuel and clearly

marked “PARAFFIN”. NEVER store fuel in the living space.

SECTION C:

FUEL GUIDE

The FF-95 is designed for use with Parafﬁn. Use of low-quality fuel will cause burner performance to drop, leading

to abnormal combustion and reduced heater life.

Purchase only Paraffin, in non-red cans reserved exclusively for fuel and marked accordingly with the word

“PARAFFIN”. Always store your fuel in a separate area from where you store gasoline for your power equipment to

avoid accidental use of gasoline in your heater.

What to Buy . . .

ALWAYS: Clean and high-quality Parafﬁn.

ALWAYS: Fuel free of contaminants, water or cloudiness.

NEVER: Gasoline, alcohol, white gas, camp stove fuel or additives.

NEVER: Yellow or sour-smelling fuel.

RIGHT

PARAFFIN

WRONG

GAS

Danger

PARAFFIN

ENGLISH

How to Store It . . .

ALWAYS: Store in a clean container, clearly marked PARAFFIN.

ALWAYS: Store away from direct sunlight, heat sources or extreme temperature changes.

NEVER: In a glass container, or one that has been used for other fuels.

NEVER: For longer than six months. Begin each heating season with fresh fuel; discard at the end of

season.

NEVER: In the living space.

Why It is Important . . .

Pure, clean fuel is essential for safe and efﬁcient heater operation. Poor quality or contaminated fuel can

cause:

• Excess tar deposits on burner and ue pipe

• Incomplete combustion

• Reduced heater life

Use of a highly volatile ﬂammable fuel such as gasoline can produce uncontrollable ﬂames, creating a severe

ﬁre hazard.

SECTION D:

OPERATING CONTROLS AND PART NAMES

Before using heater, familiarize yourself with the following operating controls and part names.

18. Room temperature sensor

17. Circulation fan

Fan cover

Control panel

Pipe stopper

Red reset button

20.

Plumb bob

Drip tray Integral fuel strainer (inside)

19. Power

supply cord Outlet opening

Inlet opening

Front panel

Combustion

ﬂames peep

hole

Louver

ENGLISH

1. ON/OFF switch: Main switch turns heater on and off. When switched on,

heater begins operation and combustion starts after

preheat period.

2. AUTO button: The button turns weekly timer operation modes on and off

which have been programmed into weekly timer.

3. TIMER button: The button turns weekly timer set mode on and off.

4. TEMP/TIMER/CLOCK/DAY set: TEMP/TIMER/CLOCK/DAY set modes can be set by

pressing the ▲/MIN. or ▼

/HOUR buttons.

5. POWER SAVER/DAY SELECT button: The button turns POWER SAVER operation mode on and

off. When setting weekly timer, the button is used to select

a day of the week.

6. CHILD LOCK/CLEAR button: The button turns CHILD LOCK operation mode on and off.

When setting weekly timer, the CLEAR button is used.

7. ˚F/˚C switch: C/F toggle switch. ˚F/˚C toggle switch.

8. ON lamp: Lit – Heater is in operation.

Flashing – Pre-heating and pre-purging.

9. AUTO indicator: Lit – Weekly timer operation is in use.

10. TIMER indicator: Lit – Heater operating in weekly timer set mode.

11. POWER SAVER indicator: Lit – Heater operation in POWER SAVER mode.

12. CHILD LOCK indicator: Lit – Heater operation in CHILD LOCK mode.

13. BURNING MODE indicator: Lit – Heater operation at high, medium or low combustion.

14. ˚F/˚C indicator: Lit – Digital indicator shows current temp.

Flashing – Current temp can be changed.

15. SUN MON TUE WED THU FRI SAT indicator: Lit – Digital indicator shows current day or timer day.

16. ON/OFF TIMER indicator: Lit - Digital indicator shows ON/OFF timer.

17. Circulation fan: Three speed motor supplies high-capacity warm air flow

during high combustion for heating room up quickly,

and low or medium-capacity warm air flow during low or

medium combustion for maintaining comfortable room

temperature.

18. Room temperature sensor: Constantly senses room temperature and supplies

information to heater so that desired room temperature can

be maintained.

19. Power supply cord: For use in proper electrical outlet. (refer to SECTION A)

20. Plumb bob: Check that heater is level.

12. CHILD LOCK indicator

13. BURNING MODE indicator

14. ˚F/˚C indicator

16. ON/OFF TIMER indicator

8. ON lamp

1. ON/OFF switch

2. AUTO button

6. CHILD LOCK/CLEAR button

11. POWER SAVER indicator

10. TIMER indicator

9. AUTO indicator

15. SUN MON TUE WED

THU FRI SAT indicator

4. TEMP/TIMER/CLOCK/DAY set

3. TIMER button

5. POWER SAVER/DAY SELECT button

7. ˚F/˚C switch: C/F toggle switch

ENGLISH

SECTION E:

OPERATION

BEFORE IGNITION

1. Open the Valve(s)

Open the valve(s) of the external fuel tank.

2. Start the Fuel ﬂow

If using heater for the ﬁrst time, press the red reset button in order to send fuel

to the fuel sump and release.

NOTE: Make sure there is no fuel leakage from the fuel line or joints.

Also make sure fuel tank is not too high. See installation instructions.

3. Connect the Heater

Connect heater into a proper electrical outlet. (refer to SECTION A). On digital

indicator pre-set “Two Dashes” will be showing.

NOTE: Do not connect to an outlet shared with other appliances.

4. Set Clock

IMPORTANT: Clock on the heater must always be set to current time and day.

NOTE: In the event of a power failure (more than approx. 30 min.), all clock and

day may be cancelled.

5. Setting of the Time and a Day of the Week.

1) Setting of the current time

1. Press the “▲MIN.” button to set minutes and press the “▼HOUR” button to

set hours while in not operation.

2. Press the “SET” button to complete the set of the current time.

2) Setting of a day of the week

1. “dAy” sign is shown on the display and all of a day of the week will ﬂash.

Press the “

▲MIN.” button or the “▼HOUR” button to set a day of the week.

NOTE: When pressing the “

▲MIN.” button at the position of “SAT”, you can hear the beep sound and “SAT”

is not changed any more.

When pressing the “▼HOUR” button at the position of “SUN”, you can hear the beep sound and “SUN” is

not changed any more.

2. Press the “SET” button to complete the set of a day of the week.

The current time and the day of week will show on the display.

OPERATION

MANUAL OPERATION

Operation of the heater is under the direct control of the user. Heat output will, however, be automatically adjusted

in accordance with the room temperature registered by the temperature sensor.

Red Reset Button

ENGLISH

1. Turning Heater ON

1. Press ON/OFF switch to “ON” position. The current room temperature and the set

temperature will be shown on the digital indicator. ON lamp will start to ﬂash and

then blower motor and ignition will start. This lamp will continue to ﬂash during the

preheating time.

2. After approx. 1.5 – 4 minutes ignition will take place. (*) After ignition, ON lamp will

change ﬂashing to continuous. Circulation fan will turn on after approx. 2 minutes.

NOTE: (*) Pre -heating depends on the room temperature.

Room temperature:

under 0˚C 4 minutes

0˚C - 15˚C 2 minutes

15˚C 1.5 minutes

2. Adjusting Room Temperature

1. Press “

▲MIN.” or “▼HOUR” button. ˚F or ˚C will start to ﬂash.

2. Press “

▲MIN.” or “▼HOUR” button as required. Room temperature can be set from

10˚C (50˚F) to 32C (90˚F). (Initial setting : 13˚C (56˚F))

Desired temperature setting will be displayed on the digital indicator when you set

the room temperature.

When room temperature reaches the selected setting, heater will automatically shift

to “MED” or “LOW” burning mode to maintain the desired temperature.

When room temperature exceeds the selected setting by approx. 2˚C (4˚F), the heater

will automatically shut off. As room temperature drops, the heater will automatically

re-start to maintain the desired temperature.

POWER SAVER OPERATION

The Power Saver mode reduces the frequency of ignition actions, to save electric

consumption.

1. Press the POWER SAVER (DAY SELECT) button “ON” while in operation to start the

operation of the “POWER SAVER”. “POWER SAVER” sign will be shown on the digital

indicator.

When the room temperature exceeds the selected setting by approximately 6˚C (10˚F),

the heater will automatically shut off. As the room temperature becomes lower than

the selected setting, the heater will automatically re-start to maintain the desired

temperature.

CHILD LOCK OPERATION

The childproof lock can be used to prevent children accidentally changing the heater

settings. When the heater is burning and the childproof lock is on, the heater can only be

switched off. Other functions are blocked then. If the heater has already been switched off,

the childproof lock also prevents accidental ignition of the heater.

1. Press the CHILD LOCK (CLEAR) button for more than 3 seconds to set the childproof

lock while in operation or not operation. “CHILD LOCK” sign will be shown on the digital

indicator.

To release the child lock operation, press the CHILD LOCK (CLEAR) button for more

than 3 seconds.

ENGLISH

WEEKLY TIMER OPERATION

1. Set the Weekly Timer

After setting the current time and a day of the week, press the “TIMER” button to enter the weekly timer setting

mode. The “TIMER” is shown on the display. When the “TIMER” button is pressed during setting of the weekly

timer, the “TIMER” sign is disappeared and the current clock time is shown on the display.

NOTE: You cannot enter the weekly timer setting mode, while in operation at AUTO operation mode.

1) Select the program number

1. Press the “

▲MIN.” button or the “▼HOUR” button to select the program number.

The number of the program is 30. The unsetting program number is ﬂashing on the display. In the case of

the ﬁrst setting of the weekly timer, “P01” is shown on the display and will ﬂash. All of a day of the week

will also ﬂash.

NOTE: When pressing the “

▲MIN.” button at the position of “P30”, you can hear the beep sound and “P30”

is not changed any more.

When pressing the “▼HOUR” button at the position of “P01”, you can hear the beep sound and

“P01” is not changed any more.

After the program is set, the next setting program number is shown on the display. If the program

is set until “P30”, “P30” is shown on the display. Even though the program is set until “P30”, if there

is the unsetting program number, the smallest unsetting program number is shown on the display.

Example:

When “P01” and “P02” programs are already set and “P03” is not set yet, the display is indicated as

follows.

“P01” – lighting ⇔“P02” – lighting ⇔“P03” – ﬂashing

When “P01” and “P04” programs are already set and “P02” and “P03” are not set yet, the display is

indicated as follows.

“P01” – lighting ⇔“P02” – ﬂashing ⇔“P03” – ﬂashing ⇔“P04” – lighting

2. Press the “SET” button to move to the next step (2) Set the timer).

The program number is eliminated by holding the “CLEAR” button continuously for 3 seconds.

2) Set the timer

1. Press the “

▲MIN.” button or the “▼HOUR” button to set timer.

2. Press the “SET” button to complete the set of timer and to move to the next step (3) Set ON/OFF of

weeklytimer).

NOTE: When “SET” button is pressed when showing the bars sign on the display, you can hear the beep

sound and cannot move to the next step.

3) Set ON/OFF of weekly timer

1. ON and all of a day of the week will ﬂash on the display.

Press the “

▲MIN” button or the “▼HOUR” button to select ON or OFF .

2. Press “SET” to complete the set ON/OFF of weekly timer.

When you set ON, the next step is 4) Set the temperature set of the program.

When you set OFF, the next step is 5) Set a day of the week of the program.

ENGLISH

4) Set the temperature of the program

The set temperature “21” will be shown on the display and it will ﬂash.

1. Press the “

▲MIN.” button or the “▼HOUR” button to set the temperature of the program.

2. Press the “SET” button to complete the set the temperature of the program and move to the next step (5)

Set a day of the week of the program).

5) Set a day of the week of the program

1. The “dAy” sign will be shown on the display and the “SUN” will ﬂash. Press the “

▲MIN.” button or the

“▼HOUR” button to set a day of the week of the program. When pressing the “▲MIN.” button, the

program is set at the day of the week. The selected day of the week will light. When pressing the “▼HOUR”

button, the selected day of the week is not set. The unset day of the week will go off. At this time, the sign

is moved to the next day of the week automatically.

When pressing the “DAY SELECT” button, the display will be shown the next day of the week without

resetting.

2. Press the “SET” button to complete the set of a day of the week of the program and it will go back to the

select of the program number.

NOTE: If no day of week is set, when pressing the “SET” button, yo can hear the beep sound and cannot

move to the next step.

2. Activate Weekly Timer Operation

1. During operation (in a SW/ON position), press the “AUTO” button to enter the weekly timer operation mode.

The “AUTO” sign will be shown on the display.

NOTE: If no program is set, you can hear the beep sound and cannot enter the weekly timer operation mode.

2. Press the “

▲MIN.” button or the “▼HOUR” button to change the set temperature.

NOTE: If the next program starts, the temperature will be changed to the temperature of the next program.

3. During operation, press the “TIMER” button to enter the weekly timer set mode (Select of the program

number).

NOTE: If the “TIMER” button is pressed during the setting of the weekly timer set mode, the weekly timer set

mode is released.

Change of setting is applied as soon as the AUTO operation starts.

NOTE: If ON/OFF switch is pressed during the weekly timer operation mode, the weekly timer operation

mode is canceled.

ENGLISH

MANUAL COMBUSTION

IMPORTANT: This feature is for testing purpose only!

This heater also can be kept burning at desired combustion mode (High, Medium or low) manually, regardless of

room temperature.

1. Press the “

▲MIN.” button and “▼HOUR” button at the same time for more than three (3) seconds when ON /

OFF switch is “ON”.

2. P1, P2 or P3 will be displayed on the Digital indicator;

P1 = Low mode

P2 = Medium mode

P3 = High mode

Then select desired combustion mode by pressing “

▲MIN.” or “▼HOUR” button. “

▲MIN.” button changes

combustion mode to higher, “▼HOUR” button changes combustion mode to lower.

3. To clear, press the “

▲MIN.” button and “▼HOUR” button at the same time for more than (3) seconds until

normal temperature display returns.

AUTOMATIC CLEANING MODE

When the heater has been burning continuously for two hours at its highest setting, the burner will automatically

start an auto clean procedure. The display will show the auto cleaning code cl:05 running back to cl:01. The

procedure takes 5 minutes to clean the burner automatically while the heater will burn at its lowest setting. When

the burner is clean again, the heater will automatically switch back to the highest setting again.

POWER FAILURE RECOVERY SYSTEM

If at any time a power failure occurs during operation, heater will turn off. When the power returns, the unit will

automatically restart with the following conditions. Please reset each setting when the settings are erased as

indicated below.

WHEN HEATER IS IN OPERATION

TIME LENGTH OF

POWER FAILURE

0LESS THAN 3

SECONDS

MORE THAN 3 SECONDS

IN BACKUP MEMORY OUT OF BACKUP MEMORY

OPERATION Restart the combustion

with the same condition

before the power failure.

Start the combustion from the

beginning.

Start the combustion from the

beginning.

Set temperature will change to

13˚C (56˚F) for safety.

Set temperature and room

temperature will blank that at

least more than 30 min. power

failure has occurred.

To stop the blinking the

set temperature and room

temperature, press any button

once.

POWER SAVER

OPERATION

Keep the same condition

before the power failure.

Keep the same condition before

the power failure.

Keep the same condition before

the power failure.

AUTO

OPERATION

Keep the same condition

before the power failure.

Keep the same condition before

the power failure.

The setting will be erased.

(refer to SECTION E)

CHILD LOCK

OPERATION

Keep the same condition

before the power failure.

The setting will be erased.

(refer to SECTION E)

The setting will be erased.

(refer to SECTION E)

If at any time a power failure occurs when heater is not in operation, the unit will basically start the operation while

keeping the same condition before the power failure. However, when the power failure continued more than 3

seconds, the following settings will be erased. Please reset each setting.

WHEN HEATER IS NOT IN OPERATION

IN BACKUP MEMORY Child lock operation

OUT OF BACKUP MEMORY Clock and Day setting

Child lock operation

Table of contents

Other Toyotomi Heater manuals

Toyotomi

Toyotomi Zibro RS-2222 User manual

Toyotomi

Toyotomi 9078Q21 User manual

Toyotomi

Toyotomi zibro LC-30 User manual

Toyotomi

Toyotomi Radiant 10 Type N User manual

Toyotomi

Toyotomi zibro LC-35 User manual

Toyotomi

Toyotomi Laser Clean LC-32F User manual

Toyotomi

Toyotomi zibro RS - 24 User manual

Toyotomi

Toyotomi RC-41F Type C User manual

Toyotomi

Toyotomi FF-V30T User manual

Toyotomi

Toyotomi Toyoset LC-3010 User manual

Toyotomi

Toyotomi Zibro LC-135 User manual

Toyotomi

Toyotomi Radiant 40 Type D User manual

Toyotomi

Toyotomi Toyoset NS-2800 User manual

Toyotomi

Toyotomi Zibro LC-32 User manual

Toyotomi

Toyotomi EPA-100EF User manual

Toyotomi

Toyotomi RC-41 Type A User manual

Toyotomi

Toyotomi Zibro RS-29 User manual

Toyotomi

Toyotomi zibro RS-4022 User manual

Toyotomi

Toyotomi Laser 300 Owner's manual

Toyotomi

Toyotomi Zibro RS-29 User manual

Toyotomi

Toyotomi Radiant 101 Type D User manual

Toyotomi

Toyotomi zibro LC-DX320 User manual

Toyotomi

Toyotomi Radiant 101 Type A User manual

Toyotomi

Toyotomi Radiant 40 Type A User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide